Product Specification 6.1 Gb/s Short-Wavelength SFP+ Transceiver FTLF8526P3BNL PRODUCT FEATURES Up to 6.1 Gb/s bi-directional data links Hot-pluggable SFP+ footprint Built-in digital diagnostic functions 850nm Oxide VCSEL laser transmitter Duplex LC connector RoHS compliant and Lead Free 300m on high-bandwidth 50/125um (OM3) MMF Metal enclosure, for lower EMI Single 3.3V power supply < 0.5W power dissipation Extended operating temperature range: -40°C to 85°C APPLICATIONS Wireless – CPRI, OBSAI, LTE .. Finisar’s FTLF8526P3BNL SFP+ transceivers are designed for use in wireless application of links up to 6.1 Gb/s data rate over multimode fiber. The product is RoHS compliant and lead-free per Directive 2002/95/ECd PRODUCT SELECTION FTLF8526P3BNL © Finisar Corporation Aug 24, 2011 Rev. B Page 1 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 Pin Descriptions 4. Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VEET TFAULT TDIS SDA SCA MOD_ABS RS0 LOS RS1 VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Transmitter Disable. Laser output disabled on high or open. 2-wire Serial Interface Data Line (MOD-DEF2) 2-wire Serial Interface Clock (MOD-DEF1) Module Absent, connected to VEET or VEER NC Loss of Signal indication. Logic 0 indicates normal operation. NC Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 4 4 4 5 1 1 1 1 1 Notes: 1. Circuit ground is internally isolated from chassis ground. 2. TFAULT is an open collector/drain output, which should be pulled up with a 4.7k – 10k Ohms resistor on the host board if intended for use. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high output indicates a transmitter fault caused by either the TX bias current or the TX output power exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V. 3. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 4. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_ABS pulls line low to indicate module is plugged in. 5. LOS is open collector output. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal. © Finisar Corporation Aug 24, 2011 Rev. B Page 2 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 Diagram of Host Board Connector Block Pin Numbers and Names 4. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity (Non-condensing) © Finisar Corporation Aug 24, 2011 Rev. B Symbol Vcc TS TA RH Min -0.5 -40 -40 0 Typ Max 4.0 85 85 85 Unit V °C °C % Page 3 Ref. FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 III. Electrical Characteristics (TA, VCC = 3.15 to 3.46 Volts) Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Receiver Single ended data output swing Data Output Rise/Fall Time @ 6.1 Gb/s LOS Fault LOS Normal Power Supply Rejection Deterministic Jitter @ 6.1 Gb/s Total Jitter @ 6.1 Gb/s Symbol Vcc Icc Rin Vin,pp VD VEN Vout,pp tr/ tf VLOS fault VLOS norm PSR RX DJ RX TJ Min 3.15 Typ Max 3.45 180 Unit V mA Ref. 800 Vcc Vee+ 0.8 Ω mV V V 1 90 2 Vee 185 425 80 VccHOST Vee+0.8 mV ps V V mVpp ps ps 3 4 5 5 6 100 2 Vee 100 70 116 2 Notes: 1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC. 2. Or open circuit. 3. Into 100 ohms differential termination. 4. Unfiltered, 20 – 80 % 5. LOS is an open collector output. Should be pulled up with 4.7k – 10kohms on the host board. Normal operation is logic 0; loss of signal is logic 1. Maximum pull-up voltage is 5.5V. 6. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. © Finisar Corporation Aug 24, 2011 Rev. B Page 4 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 VI. Optical Characteristics (TA, VCC = 3.15 to 3.46 Volts) Parameter Transmitter Output Opt. Pwr: 50 or 62.5 MMF Optical Wavelength Spectral Width Optical Modulation Amplitude Optical Rise/Fall Time Relative Intensity Noise Receiver Receiver OMA Sensitivity Average Receiver Power Optical Center Wavelength Optical Return Loss LOS De-Assert LOS Assert LOS Hysteresis Symbol Min POUT λ σ OMA tr/ tf RIN -8.2 840 RxSENS RxMAX λC LOSD LOSA Typ Max 860 0.65 302 90 -128 76 0 770 12 860 -18 -30 0.5 Unit dBm nm nm μW ps dB/Hz μW dBm nm dB dBm dBm dB Notes: 1. Class 1 Laser Safety per FDA/CDRH, and EN (IEC) 60825 laser safety standards. 2. Unfiltered, 20-80%. Complies with FC 1x and 2x eye mask when filtered. © Finisar Corporation Aug 24, 2011 Rev. B Page 5 Ref. 1 2 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 VI. General Specifications Parameter Data Rate Bit Error Rate Fiber Length on 50/125μm highbandwidth (OM3) MMF Symbol BR BER L Min Typ 6.1 Max Units Gb/sec 10-12 300 m Max 85 85 Units °C °C Ref. 1 Notes: 1. PRBS 27-1. VI. Environmental Specifications Parameter Case Operating Temperature Storage Temperature VII. Symbol Top Tsto Min -40 -40 Typ Ref. Regulatory Compliance Finisar transceivers are Class Finisar laser transceiver complies with Laser Class 1 per latest edition of EN60825-1 and IEC 60825-1 for fiber optic systems. © Finisar Corporation Aug 24, 2011 Rev. B Page 6 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 VIII. Digital Diagnostic Functions Finisar FTLF8526P3BNL SFP+ transceivers support the 2-wire serial communication protocol as defined in the SFP MSAe. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN-2030: “Digital Diagnostics Monitoring Interface for SFP Optical Transceivers”. The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentationb,e and Finisar Application Note AN2030. Please note that evaluation board FDB-1027 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface. © Finisar Corporation Aug 24, 2011 Rev. B Page 7 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 IX. Digital Diagnostic Specifications FTLF8526P3BNL transceivers can be used in host systems that require either internally or externally calibrated digital diagnostics. Parameter Symbol Accuracy DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Dynamic Range for Rated Accuracy DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Max Reporting Range DDTemperature Internally measured transceiver temperature DDVoltage Internally measured transceiver supply voltage DDBias Measured TX bias current DDTx-Power Measured TX output power DDRx-Power Measured RX received average optical power Min Typ Max Units 3 ºC 100 mV 10 3 3 % dB dB -5 85 ºC 3.0 3.6 V 0 -9 -11 20 -2 -1 mA dBm dBm -40 125 ºC 2.8 4.0 V 0 -10 -12 20 -2 0 mA dBm dBm Notes: 1. Accuracy of Measured Tx Bias Current is 10% of the actual Bias Current from the laser driver to the laser. © Finisar Corporation Aug 24, 2011 Rev. B Page 8 Ref. 1 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 X. Mechanical Specifications Finisar’s FTLF8526P3BNL SFP+ transceivers are compatible with the SFF-8432a specification for improved pluggable form factor. FTLF8526P3BNL © Finisar Corporation Aug 24, 2011 Rev. B Page 9 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 XI. PCB Layout and Bezel Recommendations © Finisar Corporation Aug 24, 2011 Rev. B Page 10 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 © Finisar Corporation Aug 24, 2011 Rev. B Page 11 FTLF8526P3BNL Pluggable SFP+ Product Specification – August 2011 XII. References a. “Improved Pluggable Form Factor”, SFF Document Number SFF-8432, Revision 5.0, July 16, 2007. b. “Digital Monitoring Interface for Optical Transceivers”, SFF Document Number SFF-8472, Revision 11.0. c. “SFF-8431 Specifications for Enhanced Small Form Factor Pulggable Modules, SFP+”, SFF Document Number SFF-8431, Revision 4.1, July 6, 2009. d. Directive 2002/95/EC of the European Council Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment.” January 27, 2003. e. Small Form Factor Pluggable (SFP) Transceiver Multi-source Agreement (MSA), September 14, 2000. XIII. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 [email protected] www.finisar.com © Finisar Corporation Aug 24, 2011 Rev. B Page 12