Heat Shrink Tubings HS100 Series Features: • • • • • • Semi-rigid, adhesive lined, polyolefin tubing 3:1 shrink ratio Splash-resistant, moisture-resistant covering Rugged protection against abrasion, vibration and flexing Excellent strain relief and insulation of weak points Operation temperature range : -55°C to 125°C Dimension Table Size (Inches) Inside Diameter Recovered Wall Thickness As Supplied Maximum After Recovery Total Wall After Heating Meltable Wall After Heating 1/8 3.2 ±0.4 1 0.95 0.35 3/16 4.8 ±0.4 1.6 1.1 0.5 1/4 6.4 ±0.4 2.2 1.2 0.6 3/8 9.5 ±0.4 3.2 1.4 0.65 1/2 12.7 ±0.8 4.2 1.5 0.75 3/4 19.1 ±0.1 6.3 2 0.9 Dimensions : Millimetres Product Properties Property (Units) Test Method Requirement Tensile Strength (psi) ASTM D638 1,500 min. Elongation (%) ASTM D638 300 min. Cold Impact (-55°C) ASTM D746 no cracking AMS-DTL-23053 no cracking ASTM D882 25,000 max. AMS-DTL-23053 ±5 Dielectric Strength (Volts / mm) ASTM D876 1,500 min. Volume Resistivity (Ω-cm) ASTM D876 1 × 1014 UL224 no corrosion ASTM D570 2 max. - Good UL224 Pass Physical Heat Shock (250°C, 4 hrs) Secant Modulus (psi) Longitudinal Change (%) Electrical Chemical Corrosion Water Absorption (%) Fluid Resistance (23°C, 24 hrs) Flammability www.element14.com www.farnell.com www.newark.com www.cpc.co.uk Page <1> 05/04/12 V1.1 Heat Shrink Tubings HS100 Series Part Number Table Description Part Number Heat Shrink, 3:1, 3.2 mm, BLK, 10 m HS114 Heat Shrink, 3:1, 4.8 mm, BLK, 10 m HS115 Heat Shrink, 3:1, 6.4 mm, BLK, 10 m HS116 Heat Shrink, 3:1, 7.9 mm, BLK, 10 m HS117 Heat Shrink, 3:1, 9.5 mm, BLK, 10 m HS118 Heat Shrink, 3:1, 12.7 mm, BLK, 10 m HS119 Heat Shrink, 3:1, 15 mm, BLK, 10 m HS120 Heat Shrink, 3:1, 19.1 mm, BLK, 10 m HS121 Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Pro-POWER is the registered trademark of the Group. © Premier Farnell plc 2012. www.element14.com www.farnell.com www.newark.com www.cpc.co.uk Page <2> 05/04/12 V1.1