ON LM2904VDR2 Dual differential input operational amplifier Datasheet

LM358, LM258, LM2904,
LM2904A, LM2904V,
NCV2904
Single Supply Dual
Operational Amplifiers
Utilizing the circuit designs perfected for Quad Operational
Amplifiers, these dual operational amplifiers feature low power drain,
a common mode input voltage range extending to ground/VEE, and
single supply or split supply operation. The LM358 series is
equivalent to one–half of an LM324.
These amplifiers have several distinct advantages over standard
operational amplifier types in single supply applications. They can
operate at supply voltages as low as 3.0 V or as high as 32 V, with
quiescent currents about one–fifth of those associated with the
MC1741 (on a per amplifier basis). The common mode input range
includes the negative supply, thereby eliminating the necessity for
external biasing components in many applications. The output voltage
range also includes the negative power supply voltage.
• Short Circuit Protected Outputs
• True Differential Input Stage
• Single Supply Operation: 3.0 V to 32 V (LM258/LM358)
3.0 V to 26 V (LM2904, A, V)
• Low Input Bias Currents
• Internally Compensated
• Common Mode Range Extends to Negative Supply
• Single and Split Supply Operation
• ESD Clamps on the Inputs Increase Ruggedness of the Device
without Affecting Operation
http://onsemi.com
PDIP–8
N, AN, VN SUFFIX
CASE 626
8
1
SO–8
D, VD SUFFIX
CASE 751
8
1
Micro8
DMR2 SUFFIX
CASE 846A
8
1
PIN CONNECTIONS
Output A
Inputs A
VEE/Gnd
1
8
2
7
4
–
+ 5
–
+
3
6
VCC
Output B
Inputs B
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking
section on page 11 of this data sheet.
 Semiconductor Components Industries, LLC, 2002
August, 2002 – Rev. 11
1
Publication Order Number:
LM358/D
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
3.0 V to VCC(max)
VCC
VCC
1
1
2
2
1.5 V to VCC(max)
1.5 V to VEE(max)
VEE
VEE/Gnd
Single Supply
Split Supplies
Figure 1.
Output
Bias Circuitry
Common to Both
Amplifiers
VCC
Q15
Q16
Q22
Q14
Q13
40 k
Q19
5.0 pF
Q12
Q24
25
Q20
Q18
Inputs
Q2
Q5
Q4
Q11
Q9
Q21
Q17
Q3
Q23
Q6
Q26
Q25
Q7
Q8
Q10
Q1
2.4 k
2.0 k
VEE/Gnd
Figure 2. Representative Schematic Diagram
(One–Half of Circuit Shown)
http://onsemi.com
2
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.)
Rating
Power Supply Voltages
Single Supply
Split Supplies
Symbol
LM258
LM358
LM2904, LM2904A
LM2904V, NCV2904
VCC
VCC, VEE
32
±16
26
±13
Unit
Vdc
Input Differential Voltage Range (Note 1)
VIDR
±32
±26
Vdc
Input Common Mode Voltage Range (Note 2)
VICR
–0.3 to 32
–0.3 to 26
Vdc
Output Short Circuit Duration
tSC
Continuous
Junction Temperature
TJ
150
°C
Thermal Resistance, Junction–to–Air (Note 3)
RJA
238
°C/W
Storage Temperature Range
Tstg
–55 to +125
°C
ESD Tolerance – Human Body Model (Note 4)
–
2000
Operating Ambient Temperature Range
LM258
LM358
LM2904/LM2904A
LM2904V, NCV2904 (Note 5)
TA
V
°C
–25 to +85
0 to +70
–
–
–
–
–40 to +105
–40 to +125
1. Split Power Supplies.
2. For Supply Voltages less than 32 V for the LM258/358 and 26 V for the LM2904, A, V, the absolute maximum input voltage is equal to the
supply voltage.
3. RJA for Case 846A.
4. ESD data available upon request.
5. NCV2904 is qualified for automotive use.
http://onsemi.com
3
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM258
Characteristic
Min
Symbol
Input Offset Voltage
VCC = 5.0 V to 30 V (26 V for LM2904, V),
VIC = 0 V to VCC –1.7 V, VO 1.4 V, RS = 0 Ω
TA = 25°C
TA = Thigh (Note 6)
TA = Tlow (Note 6)
VIO
Average Temperature Coefficient of Input Offset
Voltage
TA = Thigh to Tlow (Note 6)
Typ
LM358
Max
Min
Typ
Max
Unit
mV
–
–
–
2.0
–
–
5.0
7.0
7.0
–
–
–
2.0
–
–
7.0
9.0
9.0
∆VIO/∆T
–
7.0
–
–
7.0
–
µV/°C
IIO
–
–
–
–
3.0
–
–45
–50
30
100
–150
–300
–
–
–
–
5.0
–
–45
–50
50
150
–250
–500
nA
∆IIO/∆T
–
10
–
–
10
–
pA/°C
Input Common Mode Voltage Range (Note 7),
VCC = 30 V
(26 V for LM2904, V)
VCC = 30 V (26 V for LM2904, V),
TA = Thigh to Tlow
VICR
0
–
28.3
0
–
28.3
V
0
–
28
0
–
28
Differential Input Voltage Range
VIDR
–
–
VCC
–
–
VCC
Large Signal Open Loop Voltage Gain
RL = 2.0 kΩ, VCC = 15 V, For Large VO Swing,
TA = Thigh to Tlow (Note 6)
AVOL
50
25
100
–
–
–
25
15
100
–
–
–
CS
–
–120
–
–
–120
–
dB
Common Mode Rejection
RS ≤ 10 kΩ
CMR
70
85
–
65
70
–
dB
Power Supply Rejection
PSR
65
100
–
65
100
–
dB
Output Voltage–High Limit
TA = Thigh to Tlow (Note 6)
VCC = 5.0 V, RL = 2.0 kΩ, TA = 25°C
VCC = 30 V (26 V for LM2904, V), RL = 2.0 kΩ
VCC = 30 V (26 V for LM2904, V), RL = 10 kΩ
VOH
Output Voltage–Low Limit
VCC = 5.0 V, RL = 10 kΩ,
TA = Thigh to Tlow (Note 6)
Input Offset Current
TA = Thigh to Tlow (Note 6)
Input Bias Current
TA = Thigh to Tlow (Note 6)
Average Temperature Coefficient of Input Offset
Current
TA = Thigh to Tlow (Note 6)
Channel Separation
1.0 kHz ≤ f ≤ 20 kHz, Input Referenced
IIB
V
V/mV
V
3.3
26
27
3.5
–
28
–
–
–
3.3
26
27
3.5
–
28
–
–
–
VOL
–
5.0
20
–
5.0
20
mV
Output Source Current
VID = +1.0 V, VCC = 15 V
IO+
20
40
–
20
40
–
mA
Output Sink Current
VID = –1.0 V, VCC = 15 V
VID = –1.0 V, VO = 200 mV
IO–
10
12
20
50
–
–
10
12
20
50
–
–
mA
µA
Output Short Circuit to Ground (Note 8)
ISC
–
40
60
–
40
60
mA
Power Supply Current (Total Device)
TA = Thigh to Tlow (Note 6)
VCC = 30 V (26 V for LM2904, V), VO = 0 V, RL = ∞
VCC = 5 V, VO = 0 V, RL = ∞
ICC
mA
–
–
1.5
0.7
3.0
1.2
–
–
1.5
0.7
3.0
1.2
6. LM258: Tlow = –25°C, Thigh = +85°C
LM358: Tlow = 0°C, Thigh = +70°C
LM2904V & NCV2904: Tlow = –40°C, Thigh = +125°C
LM2904/LM2904A: Tlow = –40°C, Thigh = +105°C
NCV2904 is qualified for automotive use.
7. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common mode voltage range is VCC –1.7 V.
8. Short circuits from the output to VCC can cause excessive heating and eventual destruction. Destructive dissipation can result from
simultaneous shorts on all amplifiers.
http://onsemi.com
4
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = Gnd, TA = 25°C, unless otherwise noted.)
LM2904
Characteristic
Symbol
Input Offset Voltage
VCC = 5.0 V to 30 V (26 V for LM2904, V),
VIC = 0 V to VCC –1.7 V, VO 1.4 V, RS = 0 Ω
TA = 25°C
TA = Thigh (Note 9)
TA = Tlow (Note 9)
VIO
Average Temperature Coefficient of Input Offset
Voltage
TA = Thigh to Tlow (Note 9)
Input Offset Current
TA = Thigh to Tlow (Note 9)
Input Bias Current
TA = Thigh to Tlow (Note 9)
Min
Typ
LM2904A
Max
Min
Typ
LM2904V, NCV2904
Max
Min
Typ
Max
Unit
mV
–
–
–
2.0
–
–
7.0
10
10
–
–
–
2.0
–
–
7.0
10
10
–
–
–
–
–
–
7.0
13
10
∆VIO/∆T
–
7.0
–
–
7.0
–
–
7.0
–
µV/°C
IIO
–
–
–
–
5.0
45
–45
–50
50
200
–250
–500
–
–
–
–
5.0
45
–45
–50
50
200
–100
–250
–
–
–
–
5.0
45
–45
–50
50
200
–250
–500
nA
IIB
Average Temperature Coefficient of Input Offset
Current
TA = Thigh to Tlow (Note 9)
∆IIO/∆T
–
10
–
–
10
–
–
10
–
pA/°C
Input Common Mode Voltage Range (Note 10),
VCC = 30 V (26 V for LM2904, V)
VCC = 30 V (26 V for LM2904, V),
TA = Thigh to Tlow
VICR
0
–
24.3
0
–
24.3
0
–
24.3
V
0
–
24
0
–
24
0
–
24
–
–
VCC
–
–
VCC
–
–
VCC
Differential Input Voltage Range
VIDR
Large Signal Open Loop Voltage Gain
RL = 2.0 kΩ, VCC = 15 V, For Large VO Swing,
TA = Thigh to Tlow (Note 9)
AVOL
V
V/mV
25
15
100
–
–
–
25
15
100
–
–
–
25
15
100
–
–
–
CS
–
–120
–
–
–120
–
–
–120
–
dB
Common Mode Rejection
RS ≤ 10 kΩ
CMR
50
70
–
50
70
–
50
70
–
dB
Power Supply Rejection
PSR
50
100
–
50
100
–
50
100
–
dB
Output Voltage–High Limit
TA = Thigh to Tlow (Note 9)
VCC = 5.0 V, RL = 2.0 kΩ, TA = 25°C
VCC = 30 V (26 V for LM2904, V), RL = 2.0 kΩ
VCC = 30 V (26 V for LM2904, V), RL = 10 kΩ
VOH
Output Voltage–Low Limit
VCC = 5.0 V, RL = 10 kΩ,
TA = Thigh to Tlow (Note 9)
Channel Separation
1.0 kHz ≤ f ≤ 20 kHz, Input Referenced
V
3.3
22
23
3.5
–
24
–
–
–
3.3
22
23
3.5
–
24
–
–
–
3.3
22
23
3.5
–
24
–
–
–
VOL
–
5.0
20
–
5.0
20
–
5.0
20
mV
Output Source Current
VID = +1.0 V, VCC = 15 V
IO+
20
40
–
20
40
–
20
40
–
mA
Output Sink Current
VID = –1.0 V, VCC = 15 V
VID = –1.0 V, VO = 200 mV
IO–
10
–
20
–
–
–
10
–
20
–
–
–
10
–
20
–
–
–
mA
µA
–
40
60
–
40
60
–
40
60
mA
Output Short Circuit to Ground (Note 11)
ISC
Power Supply Current (Total Device)
TA = Thigh to Tlow (Note 9)
VCC = 30 V (26 V for LM2904, V), VO = 0 V,
RL = ∞
VCC = 5 V, VO = 0 V, RL = ∞
ICC
mA
–
1.5
3.0
–
1.5
3.0
–
1.5
3.0
–
0.7
1.2
–
0.7
1.2
–
0.7
1.2
9. LM258: Tlow = –25°C, Thigh = +85°C
LM358: Tlow = 0°C, Thigh = +70°C
LM2904V & NCV2904: Tlow = –40°C, Thigh = +125°C
LM2904/LM2904A: Tlow = –40°C, Thigh = +105°C
NCV2904 is qualified for automotive use.
10. The input common mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3 V. The upper end of
the common mode voltage range is VCC –1.7 V.
11. Short circuits from the output to VCC can cause excessive heating and eventual destruction. Destructive dissipation can result from
simultaneous shorts on all amplifiers.
http://onsemi.com
5
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
CIRCUIT DESCRIPTION
The LM358 series is made using two internally
compensated, two–stage operational amplifiers. The first
stage of each consists of differential input devices Q20 and
Q18 with input buffer transistors Q21 and Q17 and the
differential to single ended converter Q3 and Q4. The first
stage performs not only the first stage gain function but also
performs the level shifting and transconductance reduction
functions. By reducing the transconductance, a smaller
compensation capacitor (only 5.0 pF) can be employed, thus
saving chip area. The transconductance reduction is
accomplished by splitting the collectors of Q20 and Q18.
Another feature of this input stage is that the input common
mode range can include the negative supply or ground, in
single supply operation, without saturating either the input
devices or the differential to single–ended converter. The
second stage consists of a standard current source load
amplifier stage.
Each amplifier is biased from an internal–voltage
regulator which has a low temperature coefficient thus
giving each amplifier good temperature characteristics as
well as excellent power supply rejection.
1.0 V/DIV
VCC = 15 Vdc
RL = 2.0 kΩ
TA = 25°C
5.0 µs/DIV
Figure 3. Large Signal Voltage
Follower Response
AVOL, OPEN LOOP VOLTAGE GAIN (dB)
20
VI , INPUT VOLTAGE (V)
18
16
14
12
10
Negative
8.0
Positive
6.0
4.0
2.0
0
0
2.0
4.0
6.0 8.0
10
12
14 16
VCC/VEE, POWER SUPPLY VOLTAGES (V)
18
20
120
VCC = 15 V
VEE = Gnd
TA = 25°C
100
80
60
40
20
0
-20
1.0
10
100
1.0 k
10 k
100 k
1.0 M
f, FREQUENCY (Hz)
Figure 4. Input Voltage Range
Figure 5. Large–Signal Open Loop Voltage Gain
http://onsemi.com
6
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
550
RL = 2.0 kΩ
VCC = 15 V
VEE = Gnd
Gain = -100
RI = 1.0 kΩ
RF = 100 kΩ
12
10
8.0
VO , OUTPUT VOLTAGE (mV)
VOR , OUTPUT VOLTAGE RANGE (Vpp )
14
6.0
4.0
2.0
500
VCC = 30 V
VEE = Gnd
TA = 25°C
CL = 50 pF
Input
450
400
Output
350
300
250
200
0
1.0
10
100
f, FREQUENCY (kHz)
0
1000
0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
t, TIME (ms)
Figure 6. Large–Signal Frequency Response
Figure 7. Small Signal Voltage Follower
Pulse Response (Noninverting)
TA = 25°C
RL = 2.1
1.8
I IB , INPUT BIAS CURRENT (nA)
I CC , POWER SUPPLY CURRENT (mA)
2.4
1.5
1.2
0.9
0.6
0.3
0
0
5.0
10
15
20
25
VCC, POWER SUPPLY VOLTAGE (V)
30
90
80
70
35
0
Figure 8. Power Supply Current versus
Power Supply Voltage
2.0
4.0
6.0 8.0
10
12
14 16
VCC, POWER SUPPLY VOLTAGE (V)
Figure 9. Input Bias Current versus
Supply Voltage
http://onsemi.com
7
18
20
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
50 k
R1
VCC
VCC
R2
5.0 k
-
1/2
MC1403
2.5 V
Vref
VO
LM358
10 k
+
VO = 2.5 V (1 +
R1
)
R2
1
CR
1/2
R
C
R2
-
a R1
1/2
+
b R1
R1
Vref
eo
LM358
LM358
+
LM358
Vin
-
R
VinH =
H=
-
R
C
VinL
1/2
+
Vref
R1
LM358
+
Vref
R3
-
+
For: fo
Q
TBP
TN
Where: TBP = Center Frequency Gain
TN = Passband Notch Gain
Figure 14. Bi–Quad Filter
8
1
V
2 CC
C1 = 10 C
= 1.0 kHz
= 10
=1
=1
Notch Output
LM358
http://onsemi.com
Vref =
C1
1/2
Vref
R1 = QR
R3 = TN R2
-
LM358
Vref
Bandpass
Output
1
fo = 2 π RC
R2 = R1
TBP
100 k
1/2
+
Vref
R1
(VOH - VOL)
R1 + R2
100 k
-
LM358
VinH
R1
(V - V ) + Vref
R1 + R2 OH ref
C
R
1/2
R2
VOL
Figure 13. Comparator with Hysteresis
R
R2
VO
R1
(V - V )+ Vref
VinL =
R1 + R2 OL ref
Figure 12. High Impedance Differential Amplifier
C1
VO
+
eo = C (1 + a + b) (e2 - e1)
Vin
Hysteresis
VOH
1/2
1
CR
1/2
e2
For: fo = 1.0 kHz
R = 16 kΩ
C = 0.01 µF
C
R
-
-
R
1
2 π RC
Figure 11. Wien Bridge Oscillator
LM358
R1
fo =
1
V
2 CC
Figure 10. Voltage Reference
+
VO
LM358
+
Vref =
e1
VCC
-
1/2
R
C
R1
R2
R3
= 160 kΩ
= 0.001 µF
= 1.6 MΩ
= 1.6 MΩ
= 1.6 MΩ
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
VCC
Vin
C
R1
R3
C
-
1/2
LM358
+
R2
Vref
Given:
VO
CO
CO = 10 C
1
Vref = 2 VCC
fo = center frequency
A(fo) = gain at center frequency
Choose value fo, C
Vref =
Vref
1
V
2 CC
Triangle Wave
Output
+
300 k
R3
1/2
LM358
-
75 k
R1
+
1/2
100 k
LM358
-
Vref
C
Then:
R2
Square
Wave
Output
R1 + RC
4 CRf R1
Q
π fo C
R1 =
R3
2 A(fo)
R2 =
R1 R3
4Q2 R1 -R3
For less than 10% error from operational amplifier.
Qo fo
< 0.1
BW
Where fo and BW are expressed in Hz.
Rf
f =
R3 =
if, R3 =
R2 R1
R2 + R1
If source impedance varies, filter may be preceded with voltage
follower buffer to stabilize filter parameters.
Figure 16. Multiple Feedback Bandpass Filter
Figure 15. Function Generator
http://onsemi.com
9
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
ORDERING INFORMATION
Device
Package
Operating Temperature Range
Shipping
LM358D
SO–8
98 Units/Rail
LM358DR2
SO–8
2500 Tape & Reel
LM358DMR2
Micro8
LM358N
PDIP–8
50 Units/Rail
LM258D
SO–8
98 Units/Rail
LM258DR2
SO–8
0° to +70°C
4000 Tape & Reel
2500 Tape & Reel
–25°
25° to +85°C
LM258DMR2
Micro8
LM258N
PDIP–8
4000 Tape & Reel
50 Units/Rail
LM2904D
SO–8
98 Units/Rail
LM2904DR2
SO–8
2500 Tape & Reel
LM2904DMR2
Micro8
2500 Tape & Reel
–40°
40° to +105°C
LM2904N
PDIP–8
LM2904ADMR2
Micro8
4000 Tape & Reel
LM2904AN
PDIP–8
50 Units/Rail
LM2904VD
SO–8
98 Units/Rail
LM2904VDR2
SO–8
2500 Tape & Reel
LM2904VDMR2
Micro8
LM2904VN
PDIP–8
50 Units/Rail
SO–8
2500 Tape & Reel
NCV2904DR2*
–40° to +125°C
*NCV2904 is qualified for automotive use.
http://onsemi.com
10
50 Units/Rail
4000 Tape & Reel
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
MARKING DIAGRAMS
PDIP–8
AN SUFFIX
CASE 626
PDIP–8
N SUFFIX
CASE 626
8
8
LMx58N
AWL
YYWW
8
LM2904N
AWL
YYWW
1
PDIP–8
VN SUFFIX
CASE 626
8
LM2904AN
AWL
YYWW
1
LM2904VN
AWL
YYWW
1
1
SO–8
VD SUFFIX
CASE 751
SO–8
D SUFFIX
CASE 751
8
8
LMx58
ALYW
8
2904
ALYW
1
2904V
ALYW
1
*
1
Micro8
DMR2 SUFFIX
CASE 846A
8
8
x58
AYW
1
8
2904
AYW
8
904A
AYW
1
1
x
A
WL, L
YY, Y
WW, W
904V
AYW
1
= 2 or 3
= Assembly Location
= Wafer Lot
= Year
= Work Week
*This marking diagram also applies to NCV2904DR2.
http://onsemi.com
11
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
PACKAGE DIMENSIONS
PDIP–8
N, AN, VN SUFFIX
CASE 626–05
ISSUE L
8
NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
5
–B–
1
4
DIM
A
B
C
D
F
G
H
J
K
L
M
N
F
–A–
NOTE 2
L
C
J
–T–
MILLIMETERS
MIN
MAX
9.40
10.16
6.10
6.60
3.94
4.45
0.38
0.51
1.02
1.78
2.54 BSC
0.76
1.27
0.20
0.30
2.92
3.43
7.62 BSC
--10
0.76
1.01
INCHES
MIN
MAX
0.370
0.400
0.240
0.260
0.155
0.175
0.015
0.020
0.040
0.070
0.100 BSC
0.030
0.050
0.008
0.012
0.115
0.135
0.300 BSC
--10
0.030
0.040
N
SEATING
PLANE
D
M
K
G
H
0.13 (0.005)
M
T A
M
B
M
SO–8
D, VD SUFFIX
CASE 751–07
ISSUE AA
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE MOLD
PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER
SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN
EXCESS OF THE D DIMENSION AT MAXIMUM
MATERIAL CONDITION.
6. 751-01 THRU 751-06 ARE OBSOLETE. NEW
STANDAARD IS 751-07
–X–
A
8
5
0.25 (0.010)
S
B
1
M
Y
M
4
K
–Y–
G
C
N
X 45 SEATING
PLANE
–Z–
0.10 (0.004)
H
M
D
0.25 (0.010)
M
Z Y
S
X
S
http://onsemi.com
12
J
DIM
A
B
C
D
G
H
J
K
M
N
S
MILLIMETERS
MIN
MAX
4.80
5.00
3.80
4.00
1.35
1.75
0.33
0.51
1.27 BSC
0.10
0.25
0.19
0.25
0.40
1.27
0
8
0.25
0.50
5.80
6.20
INCHES
MIN
MAX
0.189
0.197
0.150
0.157
0.053
0.069
0.013
0.020
0.050 BSC
0.004
0.010
0.007
0.010
0.016
0.050
0
8
0.010
0.020
0.228
0.244
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
PACKAGE DIMENSIONS
Micro8
DMR2 SUFFIX
CASE 846A–02
ISSUE F
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. 846A-01 OBSOLETE, NEW STANDARD 846A-02.
–A–
–B–
K
PIN 1 ID
G
D 8 PL
0.08 (0.003)
–T–
M
T B
S
A
S
SEATING
PLANE
0.038 (0.0015)
C
H
L
J
http://onsemi.com
13
DIM
A
B
C
D
G
H
J
K
L
MILLIMETERS
MIN
MAX
2.90
3.10
2.90
3.10
--1.10
0.25
0.40
0.65 BSC
0.05
0.15
0.13
0.23
4.75
5.05
0.40
0.70
INCHES
MIN
MAX
0.114
0.122
0.114
0.122
--0.043
0.010
0.016
0.026 BSC
0.002
0.006
0.005
0.009
0.187
0.199
0.016
0.028
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
Notes
http://onsemi.com
14
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
Notes
http://onsemi.com
15
LM358, LM258, LM2904, LM2904A, LM2904V, NCV2904
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make
changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death
may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada
Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada
Email: [email protected]
JAPAN: ON Semiconductor, Japan Customer Focus Center
2–9–1 Kamimeguro, Meguro–ku, Tokyo, Japan 153–0051
Phone: 81–3–5773–3850
Email: [email protected]
ON Semiconductor Website: http://onsemi.com
For additional information, please contact your local
Sales Representative.
N. American Technical Support: 800–282–9855 Toll Free USA/Canada
http://onsemi.com
16
LM358/D