Order this document by MOC8106/D SEMICONDUCTOR TECHNICAL DATA [CTR = 50–150%] GlobalOptoisolator "!" ! $ #% "! ! " [CTR = 100–300%] [CTR = 250–600%] The MOC8106, MOC8107 and MOC8108 devices consist of a gallium arsenide LED optically coupled to a silicon phototransistor in a dual–in–line package. • Closely Matched Current Transfer Ratio (CTR) Minimizes Unit–to–Unit Variation • Narrow (CTR) Windows that translate to a Narrow and Predictable Open Loop Gain Window • Very Low Coupled Capacitance along with No Chip to Pin 6 Base Connection for Minimum Noise Susceptibility • To order devices that are tested and marked per VDE 0884 requirements, the suffix “V” must be included at end of part number. VDE 0884 is a test option. STYLE 3 PLASTIC 6 1 STANDARD THRU HOLE CASE 730A–04 Applications • Switchmode Power Supplies (Feedback Control) • AC Line/Digital Logic Isolation • Interfacing and coupling systems of different potentials and impedances SCHEMATIC MAXIMUM RATINGS (TA = 25°C unless otherwise noted) Rating Symbol Value Unit IF 60 mA IF(pk) 1 A Reverse Voltage VR 6 Volts LED Power Dissipation @ TA = 25°C Derate above 25°C PD 120 1.41 mW mW/°C Collector–Emitter Voltage VCEO 70 Volts Emitter–Collector Voltage VECO 7 Volts Collector Current — Continuous IC 150 mA Detector Power Dissipation @ TA = 25°C Derate above 25°C PD 150 1.76 mW mW/°C VISO 7500 Vac(pk) Total Device Power Dissipation @ TA = 25°C Derate above 25°C PD 250 2.94 mW mW/°C Ambient Operating Temperature Range(2) TA – 55 to +100 °C Tstg – 55 to +150 °C TL 260 °C Forward Current — Peak (PW = 100 µs, 120 pps) OUTPUT TRANSISTOR 3 PIN 1. 2. 3. 4. 5. 6. 6 5 2 INPUT LED Forward Current — Continuous NC 1 NC 4 ANODE CATHODE NO CONNECTION EMITTER COLLECTOR NO CONNECTION TOTAL DEVICE Input–Output Isolation Voltage(1) (f = 60 Hz, t = 1 sec.) Storage Temperature Range(2) Lead Soldering Temperature (1/16″ from case, 10 sec. duration) 1. Input–Output Isolation Voltage, VISO, is an internal device dielectric breakdown rating. 1. For this test, Pins 1 and 2 are common, and Pins 4 and 5 are common. 2. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions. GlobalOptoisolator is a trademark of Motorola, Inc. REV 3 Optoelectronics Device Data Motorola Motorola, Inc. 1997 1 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)(1) Symbol Min Typ(1) Max Unit Forward Voltage (IF = 10 mA) VF 1.0 1.15 1.5 Volts Reverse Leakage Current (VR = 5.0 V) IR — 0.05 10 µA Capacitance C — 18 — pF (VCE = 10 V, TA = 25°C) ICEO1 — 1.0 50 nA (VCE = 10 V, TA = 100°C) ICEO2 — 1.0 — µA Collector–Emitter Breakdown Voltage (IC = 1.0 mA) V(BR)CEO 70 100 — Volts Emitter–Collector Breakdown Voltage (IE = 100 µA) V(BR)ECO 7.0 7.8 — Volts CCE — 7.0 — pF IC (CTR)(2) 5.0 (50) 10 (100) 25 (250) — — — 15 (150) 30 (300) 60 (600) mA (%) VCE(sat) — 0.15 0.4 Volts Turn–On Time (IC = 2.0 mA, VCC = 10 V, RL = 100 Ω)(3) ton — 7.5 — µs Turn–Off Time (IC = 2.0 mA, VCC = 10 V, RL = 100 Ω)(3) Characteristic INPUT LED OUTPUT TRANSISTOR Collector–Emitter Dark Current Collector–Emitter Capacitance (f = 1.0 MHz, VCE = 0) COUPLED Output Collector Current (IF = 10 mA, VCE = 10 V) MOC8106 MOC8107 MOC8108 Collector–Emitter Saturation Voltage (IC = 500 µA, IF = 5.0 mA) toff — 5.7 — µs Rise Time (IC = 2.0 mA, VCC = 10 V, RL = 100 Ω)(3) tr — 3.2 — µs Fall Time (IC = 2.0 mA, VCC = 10 V, RL = 100 Ω)(3) tf — 4.7 — µs Isolation Voltage (f = 60 Hz, t = 1.0 sec.)(4) VISO 7500 — — Vac(pk) Isolation Resistance (VI–O = 500 V)(4) RISO 1011 — — Ω Isolation Capacitance (VI–O = 0, f = 1.0 MHz)(4) CISO — 0.2 — pF 1. 2. 3. 4. Always design to the specified minimum/maximum electrical limits (where applicable). Current Transfer Ratio (CTR) = IC/IF x 100%. For test circuit setup and waveforms, refer to Figure 7. For this test, Pins 1 and 2 are common, and Pins 4 and 5 are common. 2 VF, FORWARD VOLTAGE (VOLTS) PULSE ONLY PULSE OR DC 1.8 1.6 1.4 TA = –55°C 1.2 25°C 100°C 1 1 10 100 IF, LED FORWARD CURRENT (mA) 1000 Figure 1. LED Forward Voltage versus Forward Current 2 I C , OUTPUT COLLECTOR CURRENT (NORMALIZED) TYPICAL CHARACTERISTICS NORMALIZED TO: IF = 10 mA 1 0.1 0.01 0.5 1 2 5 10 20 IF, LED INPUT CURRENT (mA) 50 Figure 2. Output Current versus Input Current Motorola Optoelectronics Device Data IC, OUTPUT COLLECTOR CURRENT (mA) 35 IF = 10 mA 30 MOC8108 25 20 MOC8107 15 10 MOC8106 5 0 0 1 2 3 4 5 6 7 8 9 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) 10 7 5 NORMALIZED TO TA = 25°C 2 1 0.7 0.5 0.2 0.1 –60 –40 –20 0 20 40 60 80 TA, AMBIENT TEMPERATURE (°C) 100 Figure 4. Output Current versus Ambient Temperature 20 100 CLED 18 NORMALIZED TO: VCE = 10 V TA = 25°C f = 1 MHz 16 C, CAPACITANCE (pF) ICEO, COLLECTOR–EMITTER DARK CURRENT (NORMALIZED) Figure 3. Collector Current versus Collector–Emitter Voltage IC , OUTPUT COLLECTOR CURRENT (NORMALIZED) 10 10 VCE = 30 V 1 14 12 10 8 CCE 6 4 10 V 2 0.1 0 20 40 60 80 TA, AMBIENT TEMPERATURE (°C) 100 0 0.05 0.1 Figure 5. Dark Current versus Ambient Temperature 0.2 0.5 1 2 5 V, VOLTAGE (VOLTS) INPUT 50 WAVEFORMS INPUT PULSE VCC = 10 V IC 20 Figure 6. Capacitance versus Voltage TEST CIRCUIT IF 10 RL = 100 Ω 10% OUTPUT OUTPUT PULSE 90% tr ton tf toff IF = As required to produce IC = 2 mA Figure 7. Switching Time Test Circuit and Waveforms Motorola Optoelectronics Device Data 3 PACKAGE DIMENSIONS –A– 6 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4 –B– 1 3 F 4 PL C N –T– L K SEATING PLANE J 6 PL 0.13 (0.005) G M E 6 PL D 6 PL 0.13 (0.005) M T A B M M T B M A M DIM A B C D E F G J K L M N M INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.300 BSC 0_ 15 _ 0.015 0.100 STYLE 3: PIN 1. 2. 3. 4. 5. 6. MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 7.62 BSC 0_ 15 _ 0.38 2.54 ANODE CATHODE NC EMITTER COLLECTOR NC CASE 730A–04 ISSUE G –A– 6 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 4 –B– 1 S 3 F 4 PL DIM A B C D E F G H J K L S L H C –T– G J K 6 PL E 6 PL 0.13 (0.005) D 6 PL 0.13 (0.005) M T A M B M SEATING PLANE T B M A INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.020 0.025 0.008 0.012 0.006 0.035 0.320 BSC 0.332 0.390 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.51 0.63 0.20 0.30 0.16 0.88 8.13 BSC 8.43 9.90 M M CASE 730C–04 ISSUE D 4 Motorola Optoelectronics Device Data NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. –A– 6 4 –B– 1 3 L N F 4 PL C –T– SEATING PLANE G J K DIM A B C D E F G J K L N INCHES MIN MAX 0.320 0.350 0.240 0.260 0.115 0.200 0.016 0.020 0.040 0.070 0.010 0.014 0.100 BSC 0.008 0.012 0.100 0.150 0.400 0.425 0.015 0.040 MILLIMETERS MIN MAX 8.13 8.89 6.10 6.60 2.93 5.08 0.41 0.50 1.02 1.77 0.25 0.36 2.54 BSC 0.21 0.30 2.54 3.81 10.16 10.80 0.38 1.02 D 6 PL E 6 PL 0.13 (0.005) M T A M B M CASE 730D–05 ISSUE D Motorola Optoelectronics Device Data 5 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Mfax is a trademark of Motorola, Inc. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315 Mfax: [email protected] – TOUCHTONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, – US & Canada ONLY 1–800–774–1848 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 INTERNET: http://www.mot.com/SPS/ 6 ◊ MOC8106/D Motorola Optoelectronics Device Data