ONSEMI BAW56WT1

Order this document
by BAW56WT1/D
SEMICONDUCTOR TECHNICAL DATA
Motorola Preferred Device
CATHODE
1
3
ANODE
2
3
MAXIMUM RATINGS (TA = 25°C)
Symbol
Max
Unit
Reverse Voltage
VR
70
Vdc
Forward Current
IF
200
mAdc
IFM(surge)
500
mAdc
Symbol
Max
Unit
Total Device Dissipation FR– 5 Board(1)
TA = 25°C
Derate above 25°C
PD
200
mW
1.6
mW/°C
Thermal Resistance, Junction to Ambient
RqJA
0.625
°C/W
PD
300
mW
2.4
mW/°C
RqJA
417
°C/W
TJ, Tstg
– 55 to +150
°C
Rating
Peak Forward Surge Current
1
2
CASE 419–02, STYLE 4
SC–70/SOT–323
THERMAL CHARACTERISTICS
Characteristic
Total Device Dissipation
Alumina Substrate(2) TA = 25°C
Derate above 25°C
Thermal Resistance, Junction to Ambient
Junction and Storage Temperature
DEVICE MARKING
A1
ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise noted)
Characteristic
Symbol
Min
Max
Unit
V(BR)
70
—
Vdc
—
—
—
30
2.5
50
—
2.0
—
—
—
—
715
855
1000
1250
—
6.0
OFF CHARACTERISTICS
Reverse Breakdown Voltage
(I(BR) = 100 µAdc)
Reverse Voltage Leakage Current
(VR = 25 Vdc, TJ = 150°C)
(VR = 70 Vdc)
(VR = 70 Vdc, TJ = 150°C)
IR
Diode Capacitance
(VR = 0, f = 1.0 MHz)
CD
Forward Voltage
(IF = 1.0 mAdc)
(IF = 10 mAdc)
(IF = 60 mAdc)
(IF = 150 mAdc)
VF
Reverse Recovery Time
(IF = IR = 10 mAdc, RL = 100 Ω, IR(REC) = 1.0 mAdc) (Figure 1)
trr
µAdc
pF
mVdc
ns
0.062 in.
0.024 in. 99.5% alumina.
1. FR– 5 = 1.0
0.75
2. Alumina = 0.4
0.3
Thermal Clad is a trademark of the Bergquist Company
Preferred devices are Motorola recommended choices for future use and best overall value.
Motorola Small–Signal Transistors, FETs and Diodes Device Data
 Motorola, Inc. 1997
1
BAW56WT1
820 Ω
+10 V
2.0 k
100 µH
tr
0.1 µF
tp
IF
IF
t
trr
10%
t
0.1 µF
90%
DUT
50 Ω INPUT
SAMPLING
OSCILLOSCOPE
50 Ω OUTPUT
PULSE
GENERATOR
iR(REC) = 1.0 mA
IR
VR
OUTPUT PULSE
(IF = IR = 10 mA; MEASURED
at iR(REC) = 1.0 mA)
INPUT SIGNAL
Notes: 1. A 2.0 kΩ variable resistor adjusted for a Forward Current (IF) of 10 mA.
Notes: 2. Input pulse is adjusted so IR(peak) is equal to 10 mA.
Notes: 3. tp » trr
Figure 1. Recovery Time Equivalent Test Circuit
10
100
IR , REVERSE CURRENT (µA)
IF, FORWARD CURRENT (mA)
TA = 150°C
10
TA = 85°C
TA = 25°C
1.0
TA = 125°C
1.0
TA = 85°C
0.1
TA = 55°C
0.01
TA = – 40°C
TA = 25°C
0.001
0.1
0.2
0.4
0.6
0.8
1.0
VF, FORWARD VOLTAGE (VOLTS)
0
1.2
10
Figure 2. Forward Voltage
20
30
40
VR, REVERSE VOLTAGE (VOLTS)
50
Figure 3. Leakage Current
CD, DIODE CAPACITANCE (pF)
1.75
1.5
1.25
1.0
0.75
0
2
4
6
8
VR, REVERSE VOLTAGE (VOLTS)
Figure 4. Capacitance
2
Motorola Small–Signal Transistors, FETs and Diodes Device Data
BAW56WT1
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the semiconductor packages must
be the correct size to insure proper solder connection
interface between the board and the package. With the
correct pad geometry, the packages will self align when
subjected to a solder reflow process.
0.025
0.65
0.025
0.65
0.075
1.9
0.035
0.9
0.028
0.7
inches
mm
SC-70/SOT-323 POWER DISSIPATION
The power dissipation of the SC-70/SOT-323 is a function
of the collector pad size. This can vary from the minimum
pad size for soldering to the pad size given for maximum
power dissipation. Power dissipation for a surface mount
device is determined by TJ(max), the maximum rated junction
temperature of the die, RθJA, the thermal resistance from the
device junction to ambient; and the operating temperature,
TA. Using the values provided on the data sheet, PD can be
calculated as follows.
PD =
TJ(max) – TA
RθJA
The values for the equation are found in the maximum
ratings table on the data sheet. Substituting these values into
the equation for an ambient temperature TA of 25°C, one can
calculate the power dissipation of the device which in this
case is 200 milliwatts.
PD =
150°C – 25°C
0.625°C/W
= 200 milliwatts
The 0.625°C/W assumes the use of the recommended
footprint on a glass epoxy printed circuit board to achieve a
power dissipation of 200 milliwatts. Another alternative would
be to use a ceramic substrate or an aluminum core board
such as Thermal Clad. Using a board material such as
Thermal Clad, a power dissipation of 300 milliwatts can be
achieved using the same footprint.
SOLDERING PRECAUTIONS
The melting temperature of solder is higher than the rated
temperature of the device. When the entire device is heated
to a high temperature, failure to complete soldering within a
short time could result in device failure. Therefore, the
following items should always be observed in order to
minimize the thermal stress to which the devices are
subjected.
• Always preheat the device.
• The delta temperature between the preheat and
soldering should be 100°C or less.*
• When preheating and soldering, the temperature of the
leads and the case must not exceed the maximum
temperature ratings as shown on the data sheet. When
using infrared heating with the reflow soldering method,
the difference should be a maximum of 10°C.
• The soldering temperature and time should not exceed
260°C for more than 10 seconds.
• When shifting from preheating to soldering, the
maximum temperature gradient should be 5°C or less.
• After soldering has been completed, the device should
be allowed to cool naturally for at least three minutes.
Gradual cooling should be used as the use of forced
cooling will increase the temperature gradient and result
in latent failure due to mechanical stress.
• Mechanical stress or shock should not be applied during
cooling
* Soldering a device without preheating can cause excessive
thermal shock and stress which can result in damage to the
device.
Motorola Small–Signal Transistors, FETs and Diodes Device Data
3
BAW56WT1
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the surface mounted package
should be the same as the pad size on the printed circuit
board, i.e., a 1:1 registration.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 5 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
STEP 1
PREHEAT
ZONE 1
“RAMP”
200°C
STEP 2
STEP 3
VENT
HEATING
“SOAK” ZONES 2 & 5
“RAMP”
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177 –189°C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 6 STEP 7
VENT COOLING
STEP 5
STEP 4
HEATING
HEATING
ZONES 3 & 6 ZONES 4 & 7
“SPIKE”
“SOAK”
205° TO 219°C
PEAK AT
SOLDER JOINT
170°C
160°C
150°C
150°C
140°C
100°C
100°C
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
50°C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
Figure 5. Typical Solder Heating Profile
4
Motorola Small–Signal Transistors, FETs and Diodes Device Data
BAW56WT1
PACKAGE DIMENSIONS
A
L
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3
B
S
1
2
D
V
G
C
0.05 (0.002)
H
R N
J
K
CASE 419-02
ISSUE H
SC–70/SOT–323
Motorola Small–Signal Transistors, FETs and Diodes Device Data
DIM
A
B
C
D
G
H
J
K
L
N
R
S
V
INCHES
MIN
MAX
0.071
0.087
0.045
0.053
0.035
0.049
0.012
0.016
0.047
0.055
0.000
0.004
0.004
0.010
0.017 REF
0.026 BSC
0.028 REF
0.031
0.039
0.079
0.087
0.012
0.016
MILLIMETERS
MIN
MAX
1.80
2.20
1.15
1.35
0.90
1.25
0.30
0.40
1.20
1.40
0.00
0.10
0.10
0.25
0.425 REF
0.650 BSC
0.700 REF
0.80
1.00
2.00
2.20
0.30
0.40
STYLE 4:
PIN 1. CATHODE
2. CATHODE
3. ANODE
5
BAW56WT1
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
6
◊
Motorola Small–Signal Transistors, FETs and Diodes BAW56WT1/D
Device Data