Cypress CY7C1474BV25 72-mbit (2 m x 36/4 m x 18/1 m x 72) pipelined sram with nobl architecture Datasheet

CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
72-Mbit (2 M × 36/4 M × 18/1 M × 72)
Pipelined SRAM with NoBL™ Architecture
72-Mbit (2 M × 36/4 M × 18/1 M × 72) Pipelined SRAM with NoBL™ Architecture
Features
Functional Description
■
Pin-compatible and functionally equivalent to ZBT™
■
Supports 250 MHz bus operations with zero wait states
❐ Available speed grades are 250, 200, and 167 MHz
■
Internally self-timed output buffer control to eliminate the need
to use asynchronous OE
■
Fully registered (inputs and outputs) for pipelined operation
■
Byte Write capability
■
Single 2.5 V power supply
■
2.5 V IO supply (VDDQ)
■
Fast clock-to-output times
❐ 3.0 ns (for 250-MHz device)
■
Clock Enable (CEN) pin to suspend operation
■
Synchronous self-timed writes
■
CY7C1470BV25,
CY7C1472BV25
available
in
JEDEC-standard Pb-free 100-pin TQFP, Pb-free and
non-Pb-free 165-ball FBGA package. CY7C1474BV25
available in Pb-free and non-Pb-free 209-ball FBGA package
■
IEEE 1149.1 JTAG Boundary Scan compatible
■
Burst capability—linear or interleaved burst order
■
“ZZ” Sleep Mode option and Stop Clock option
The CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25
are 2.5 V, 2 M × 36/4 M × 18/1 M × 72 synchronous pipelined
burst SRAMs with No Bus Latency™ (NoBL logic,
respectively. They are designed to support unlimited true
back-to-back read or write operations with no wait states. The
CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25 are
equipped with the advanced (NoBL) logic required to enable
consecutive read or write operations with data being transferred
on every clock cycle. This feature dramatically improves the
throughput of data in systems that require frequent read or write
transitions. The CY7C1470BV25, CY7C1472BV25, and
CY7C1474BV25 are pin-compatible and functionally equivalent
to ZBT devices.
All synchronous inputs pass through input registers controlled by
the rising edge of the clock. All data outputs pass through output
registers controlled by the rising edge of the clock. The clock
input is qualified by the Clock Enable (CEN) signal, which when
deasserted suspends operation and extends the previous clock
cycle. Write operations are controlled by the Byte Write Selects
(BWa–BWd
for
CY7C1470BV25,
BWa–BWb
for
CY7C1472BV25, and BWa–BWh for CY7C1474BV25) and a
Write Enable (WE) input. All writes are conducted with on-chip
synchronous self-timed write circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. To avoid bus contention,
the output drivers are synchronously tri-stated during the data
portion of a write sequence.
Selection Guide
Description
Maximum Access Time
Maximum Operating Current
Maximum CMOS Standby Current
Cypress Semiconductor Corporation
Document Number: 001-15032 Rev. *I
•
250 MHz
200 MHz
167 MHz
Unit
3.0
450
120
3.0
450
120
3.4
400
120
ns
mA
mA
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised May 17, 2011
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Logic Block Diagram – CY7C1470BV25 (2 M × 36)
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
S
E
N
S
E
ADV/LD
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
BW a
BW b
BW c
BW d
WRITE
DRIVERS
MEMORY
ARRAY
A
M
P
S
WE
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
E
INPUT
REGISTER 1
OE
CE1
CE2
CE3
ZZ
S
T
E
E
R
I
N
G
INPUT
REGISTER 0
E
O
U
T
P
U
T
D
A
T
A
B
U
F
F
E
R
S
DQ s
DQ Pa
DQ Pb
DQ Pc
DQ Pd
E
E
READ LOGIC
SLEEP
CONTROL
Logic Block Diagram – CY7C1472BV25 (4 M × 18)
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
S
E
N
S
E
ADV/LD
BW a
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
A
M
P
S
BW b
WE
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
O
U
T
P
U
T
D
A
T
A
B
U
F
F
E
R
S
S
T
E
E
R
I
N
G
E
INPUT
REGISTER 1
OE
CE1
CE2
CE3
ZZ
Document Number: 001-15032 Rev. *I
E
DQ s
DQ Pa
DQ Pb
E
INPUT
REGISTER 0
E
READ LOGIC
Sleep
Control
Page 2 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Logic Block Diagram – CY7C1474BV25 (1 M × 72)
A0, A1, A
ADDRESS
REGISTER 0
A1
A1'
D1
Q1
A0
A0'
BURST
D0
Q0
LOGIC
MODE
CLK
CEN
ADV/LD
C
C
WRITE ADDRESS
REGISTER 1
WRITE ADDRESS
REGISTER 2
S
E
N
S
E
ADV/LD
BW a
BW b
BW c
BW d
BW e
BW f
BW g
BW h
WRITE REGISTRY
AND DATA COHERENCY
CONTROL LOGIC
WRITE
DRIVERS
MEMORY
ARRAY
A
M
P
S
O
U
T
P
U
T
R
E
G
I
S
T
E
R
S
O
U
T
P
U
T
D
A
T
A
B
U
F
F
E
R
S
S
T
E
E
R
I
N
G
E
E
DQ s
DQ Pa
DQ Pb
DQ Pc
DQ Pd
DQ Pe
DQ Pf
DQ Pg
DQ Ph
WE
INPUT
REGISTER 1
OE
CE1
CE2
CE3
ZZ
Document Number: 001-15032 Rev. *I
E
INPUT
REGISTER 0
E
READ LOGIC
Sleep
Control
Page 3 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Contents
Pin Configurations ........................................................... 5
Pin Definitions .................................................................. 7
Functional Overview ........................................................ 8
Single Read Accesses ................................................ 8
Burst Read Accesses .................................................. 8
Single Write Accesses ................................................. 8
Burst Write Accesses .................................................. 9
Sleep Mode ................................................................. 9
Linear Burst Address Table (MODE = GND) .................. 9
Interleaved Burst Address Table
(MODE = Floating or VDD) ............................................... 9
ZZ Mode Electrical Characteristics ................................. 9
Truth Table ...................................................................... 10
Partial Write Cycle Description ..................................... 11
IEEE 1149.1 Serial Boundary Scan (JTAG) .................. 12
Disabling the JTAG Feature ...................................... 12
TAP Controller State Diagram ....................................... 12
Test Access Port (TAP) ............................................. 12
TAP Controller Block Diagram ...................................... 12
Performing a TAP RESET ......................................... 12
TAP Registers ........................................................... 12
TAP Instruction Set ................................................... 13
TAP Timing ...................................................................... 14
TAP AC Switching Characteristics ............................... 15
2.5 V TAP AC Test Conditions ....................................... 16
2.5 V TAP AC Output Load Equivalent ......................... 16
TAP DC Electrical Characteristics and
Operating Conditions ..................................................... 16
Document Number: 001-15032 Rev. *I
Identification Register Definitions ................................ 16
Scan Register Sizes ....................................................... 16
Identification Codes ....................................................... 17
Boundary Scan Exit Order (2 M × 36) ........................... 17
Boundary Scan Exit Order (4 M × 18) ........................... 18
Boundary Scan Exit Order (1 M × 72) ........................... 18
Maximum Ratings ........................................................... 19
Operating Range ............................................................. 19
Electrical Characteristics ............................................... 19
Capacitance .................................................................... 20
Thermal Resistance ........................................................ 20
AC Test Loads and Waveforms ..................................... 20
Switching Characteristics .............................................. 21
Switching Waveforms .................................................... 22
Ordering Information ...................................................... 24
Ordering Code Definitions ......................................... 24
Package Diagrams .......................................................... 25
Acronyms ........................................................................ 27
Document Conventions ................................................. 27
Units of Measure ....................................................... 27
Document History Page ................................................. 28
Sales, Solutions, and Legal Information ...................... 29
Worldwide Sales and Design Support ....................... 29
Products .................................................................... 29
PSoC Solutions ......................................................... 29
Page 4 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Pin Configurations
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
CY7C1472BV25
(4 M × 18)
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
Document Number: 001-15032 Rev. *I
A
NC
NC
VDDQ
VSS
NC
DQPa
DQa
DQa
VSS
VDDQ
DQa
DQa
VSS
NC
VDD
ZZ
DQa
DQa
VDDQ
VSS
DQa
DQa
NC
NC
VSS
VDDQ
NC
NC
NC
A
A
A
A
A
A
A
A
A
VSS
VDD
NC(288)
NC(144)
A
A
A
A
A
A
A
A
A
VSS
VDD
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC
DQPb
NC
DQb
NC
DQb
VDDQ VDDQ
VSS
VSS
NC
DQb
DQb
NC
DQb
DQb
DQb
DQb
VSS
VSS
VDDQ VDDQ
DQb
DQb
DQb
DQb
NC
VSS
VDD
NC
NC
VDD
VSS
ZZ
DQb
DQa
DQa
DQb
VDDQ VDDQ
VSS
VSS
DQa
DQb
DQa
DQb
DQa DQPb
DQa
NC
VSS
VSS
VDDQ VDDQ
NC
DQa
DQa
NC
DQPa
NC
MODE
A
A
A
A
A1
A0
CY7C1470BV25
(2 M × 36)
NC(288)
NC(144)
DQc
DQc
NC
VDD
NC
VSS
DQd
DQd
VDDQ
VSS
DQd
DQd
DQd
DQd
VSS
VDDQ
DQd
DQd
DQPd
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
VSS
DQc
DQc
DQc
DQc
VSS
VDDQ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
MODE
A
A
A
A
A1
A0
DQPc
DQc
DQc
VDDQ
A
A
A
A
CE1
CE2
NC
NC
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
A
A
A
A
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
A
A
CE1
CE2
BWd
BWc
BWb
BWa
CE3
VDD
VSS
CLK
WE
CEN
OE
ADV/LD
A
A
Figure 1. 100-pin TQFP Pinout
Page 5 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Pin Configurations (continued)
165-ball FBGA (15 × 17 × 1.4 mm) Pinout
CY7C1470BV25 (2 M × 36)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
G
H
J
K
L
M
N
P
NC/576M
A
CE1
BWc
BWb
CE3
ADV/LD
A
A
NC
BWa
VSS
CLK
CEN
WE
OE
A
A
NC
VSS
VSS
VSS
VDD
VDDQ
DQPb
DQb
R
NC/1G
A
CE2
DQPc
DQc
NC
DQc
VDDQ
VDDQ
BWd
VSS
VDD
VSS
VSS
VSS
VDDQ
NC
DQb
DQc
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQb
DQb
DQc
DQc
NC
DQd
DQc
VDDQ
VDD
VSS
VSS
VSS
VDD
DQb
DQb
DQc
NC
DQd
VDDQ
NC
VDDQ
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
DQb
NC
DQa
DQb
ZZ
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQd
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
DQa
DQd
DQPd
DQd
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQa
NC
DQa
DQPa
NC/144M
A
A
A
TDI
A1
TDO
A
A
A
MODE
A
A
A
TMS
A0
TCK
A
A
A
A
8
9
10
11
A
A
NC/288M
CY7C1472BV25 (4 M × 18)
1
2
NC/576M
A
3
4
5
6
CE3
CEN
ADV/LD
A
CE2
BWb
NC
NC
CE1
NC/1G
A
NC
NC
7
BWa
CLK
A
NC
VDDQ
VDDQ
VSS
VDD
VSS
VSS
VSS
VSS
OE
VSS
A
NC
DQb
WE
VSS
VSS
VDD
VDDQ
VDDQ
NC
NC
DQPa
DQa
NC
DQb
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
NC
DQa
NC
NC
NC
DQb
DQb
VDDQ
VDDQ
NC
VDDQ
VDD
VDD
VDD
VDD
VDDQ
VDDQ
NC
VDDQ
NC
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
DQb
NC
NC
NC
NC
DQa
DQa
DQa
ZZ
NC
DQb
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
NC
DQb
NC
VDDQ
VDD
VSS
VSS
VSS
VDD
VDDQ
DQa
NC
NC
NC
A
B
C
D
E
F
G
H
J
K
L
M
N
P
DQb
DQPb
NC
NC
VDDQ
VDDQ
VDD
VSS
VSS
NC
VSS
NC
VSS
NC
VDD
VSS
VDDQ
VDDQ
DQa
NC
NC/144M
A
A
A
TDI
A1
TDO
A
A
A
R
MODE
A
A
A
TMS
A0
TCK
A
A
A
Document Number: 001-15032 Rev. *I
NC/288M
A
Page 6 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Pin Definitions
Pin Name
IO Type
Pin Description
A0
A1
A
InputSynchronous
Address Inputs Used to Select One of the Address Locations. Sampled at the rising edge of the
CLK.
BWa
BWb
BWc
BWd
BWe
BWf
BWg
BWh
InputSynchronous
Byte Write Select Inputs, Active LOW. Qualified with WE to conduct writes to the SRAM. Sampled
on the rising edge of CLK. BWa controls DQa and DQPa, BWb controls DQb and DQPb, BWc controls
DQc and DQPc, BWd controls DQd and DQPd, BWe controls DQe and DQPe, BWf controls DQf and
DQPf, BWg controls DQg and DQPg, BWh controls DQh and DQPh.
WE
InputSynchronous
Write Enable Input, Active LOW. Sampled on the rising edge of CLK if CEN is active LOW. This
signal must be asserted LOW to initiate a write sequence.
ADV/LD
InputSynchronous
Advance/Load Input Used to Advance the On-Chip Address Counter or Load a New Address.
When HIGH (and CEN is asserted LOW) the internal burst counter is advanced. When LOW, a new
address can be loaded into the device for an access. After being deselected, ADV/LD must be driven
LOW to load a new address.
CLK
InputClock
Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN. CLK
is only recognized if CEN is active LOW.
CE1
InputSynchronous
Chip Enable 1 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE2 and CE3 to select/deselect the device.
CE2
InputSynchronous
Chip Enable 2 Input, Active HIGH. Sampled on the rising edge of CLK. Used in conjunction with
CE1 and CE3 to select/deselect the device.
CE3
InputSynchronous
Chip Enable 3 Input, Active LOW. Sampled on the rising edge of CLK. Used in conjunction with
CE1 and CE2 to select/deselect the device.
OE
InputAsynchronous
Output Enable, Active LOW. Combined with the synchronous logic block inside the device to control
the direction of the IO pins. When LOW, the IO pins can behave as outputs. When deasserted HIGH,
IO pins are tri-stated, and act as input data pins. OE is masked during the data portion of a write
sequence, during the first clock when emerging from a deselected state and when the device has
been deselected.
CEN
InputSynchronous
Clock Enable Input, Active LOW. When asserted LOW the clock signal is recognized by the SRAM.
When deasserted HIGH the clock signal is masked. Since deasserting CEN does not deselect the
device, CEN can be used to extend the previous cycle when required.
DQs
IOSynchronous
Bidirectional Data IO Lines. As inputs, they feed into an on-chip data register that is triggered by
the rising edge of CLK. As outputs, they deliver the data contained in the memory location specified
by A[18:0] during the previous clock rise of the read cycle. The direction of the pins is controlled by
OE and the internal control logic. When OE is asserted LOW, the pins can behave as outputs. When
HIGH, DQa–DQh are placed in a tri-state condition. The outputs are automatically tri-stated during
the data portion of a write sequence, during the first clock when emerging from a deselected state, and
when the device is deselected, regardless of the state of OE.
DQPX
IOSynchronous
Bidirectional Data Parity IO Lines. Functionally, these signals are identical to DQ[71:0]. During write
sequences, DQPa is controlled by BWa, DQPb is controlled by BWb, DQPc is controlled by BWc, and
DQPd is controlled by BWd, DQPe is controlled by BWe, DQPf is controlled by BWf, DQPg is controlled
by BWg, DQPh is controlled by BWh.
MODE
Input Strap Pin
Mode Input. Selects the burst order of the device. Tied HIGH selects the interleaved burst order.
Pulled LOW selects the linear burst order. MODE must not change states during operation. When
left floating MODE defaults HIGH, to an interleaved burst order.
TDO
TDI
JTAG Serial
Output
Synchronous
Serial Data Out to the JTAG Circuit. Delivers data on the negative edge of TCK.
JTAG Serial Input Serial Data In to the JTAG Circuit. Sampled on the rising edge of TCK.
Synchronous
Document Number: 001-15032 Rev. *I
Page 7 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Pin Definitions (continued)
Pin Name
TMS
IO Type
Test Mode Select TMS Pin Controls the Test Access Port State Machine. Sampled on the rising edge of TCK.
Synchronous
TCK
JTAG Clock
VDD
Power Supply
VDDQ
Pin Description
Clock Input to the JTAG Circuitry.
Power Supply Inputs to the Core of the Device.
IO Power Supply Power Supply for the IO Circuitry.
VSS
Ground
NC
–
No Connects. This pin is not connected to the die.
NC(144M,
288M,
576M, 1G)
–
These Pins are Not Connected. They are used for expansion to the 144M, 288M, 576M, and 1G
densities.
InputAsynchronous
ZZ “Sleep” Input. This active HIGH input places the device in a non-time critical “sleep” condition
with data integrity preserved. For normal operation, this pin has must be LOW or left floating.
ZZ pin has an internal pull down.
Functional Overview
register and onto the data bus within 2.6 ns (250-MHz device)
provided OE is active LOW. After the first clock of the read
access the output buffers are controlled by OE and the internal
control logic. OE must be driven LOW to drive out the requested
data. During the second clock, a subsequent operation (read,
write, or deselect) can be initiated. Deselecting the device is also
pipelined. Therefore, when the SRAM is deselected at clock rise
by one of the chip enable signals, its output tri-states following
the next clock rise.
ZZ
Ground for the Device. Must be connected to ground of the system.
The CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25
are synchronous-pipelined Burst NoBL SRAMs designed
specifically to eliminate wait states during read or write
transitions. All synchronous inputs pass through input registers
controlled by the rising edge of the clock. The clock signal is
qualified with the Clock Enable input signal (CEN). If CEN is
HIGH, the clock signal is not recognized and all internal states
are maintained. All synchronous operations are qualified with
CEN. All data outputs pass through output registers controlled by
the rising edge of the clock. Maximum access delay from the
clock rise (tCO) is 3.0 ns (250-MHz device).
Accesses can be initiated by asserting all three Chip Enables
(CE1, CE2, CE3) active at the rising edge of the clock. If CEN is
active LOW and ADV/LD is asserted LOW, the address
presented to the device is latched. The access can either be a
read or write operation, depending on the status of the Write
Enable (WE). BW[x] can be used to conduct Byte Write
operations.
Write operations are qualified by the Write Enable (WE). All
writes are simplified with on-chip synchronous self-timed write
circuitry.
Three synchronous Chip Enables (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) simplify depth expansion. All
operations (reads, writes, and deselects) are pipelined. ADV/LD
must be driven LOW after the device is deselected to load a new
address for the next operation.
Single Read Accesses
A read access is initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, (3) the input signal WE is
deasserted HIGH, and (4) ADV/LD is asserted LOW. The
address presented to the address inputs is latched into the
Address Register and presented to the memory core and control
logic. The control logic determines that a read access is in
progress and allows the requested data to propagate to the input
of the output register. At the rising edge of the next clock the
requested data is allowed to propagate through the output
Document Number: 001-15032 Rev. *I
Burst Read Accesses
The CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25
have an on-chip burst counter that enables the user to supply a
single address and conduct up to four reads without reasserting
the address inputs. ADV/LD must be driven LOW to load a new
address into the SRAM, as described in the Single Read
Accesses section. The sequence of the burst counter is
determined by the MODE input signal. A LOW input on MODE
selects a linear burst mode, a HIGH selects an interleaved burst
sequence. Both burst counters use A0 and A1 in the burst
sequence, and wraps around when incremented sufficiently. A
HIGH input on ADV/LD increments the internal burst counter
regardless of the state of chip enables inputs or WE. WE is
latched at the beginning of a burst cycle. Therefore, the type of
access (read or write) is maintained throughout the burst
sequence.
Single Write Accesses
Write accesses are initiated when the following conditions are
satisfied at clock rise: (1) CEN is asserted LOW, (2) CE1, CE2,
and CE3 are ALL asserted active, and (3) the signal WE is
asserted LOW. The address presented to the address inputs is
loaded into the Address Register. The write signals are latched
into the Control Logic block.
On the subsequent clock rise the data lines are automatically
tri-stated regardless of the state of the OE input signal. This
allows the external logic to present the data on DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1470BV25, DQa,b/DQPa,b for
CY7C1472BV25, and DQa,b,c,d,e,f,g,h/DQPa,b,c,d,e,f,g,h for
CY7C1474BV25). In addition, the address for the subsequent
Page 8 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
access (read, write, or deselect) is latched into the Address
Register (provided the appropriate control signals are asserted).
On the next clock rise the data presented to DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1470BV25, DQa,b/DQPa,b for
CY7C1472BV25,
DQa,b,c,d,e,f,g,h/DQPa,b,c,d,e,f,g,h
for
CY7C1474BV25) (or a subset for Byte Write operations, see
Partial Write Cycle Description on page 11 for details) inputs is
latched into the device and the Write is complete.
The data written during the Write operation is controlled by BW
(BWa,b,c,d for CY7C1470BV25, BWa,b for CY7C1472BV25, and
BWa,b,c,d,e,f,g,h
for
CY7C1474BV25)
signals.
The
CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25
provides Byte Write capability that is described in Partial Write
Cycle Description on page 11. Asserting the WE input with the
selected BW input selectively writes to only the desired bytes.
Bytes not selected during a Byte Write operation remain
unaltered. A synchronous self-timed write mechanism has been
provided to simplify the write operations. Byte Write capability
has been included to greatly simplify read, modify, or write
sequences, which can be reduced to simple Byte Write
operations.
Because the CY7C1470BV25, CY7C1472BV25, and
CY7C1474BV25 are common IO devices, data must not be
driven into the device while the outputs are active. OE can be
deasserted HIGH before presenting data to the DQ and DQP
(DQa,b,c,d/DQPa,b,c,d for CY7C1470BV25, DQa,b/DQPa,b for
CY7C1472BV25, and DQa,b,c,d,e,f,g,h/DQPa,b,c,d,e,f,g,h for
CY7C1474BV25) inputs. Doing so tri-states the output drivers.
As a safety precaution, DQ and DQP (DQa,b,c,d/DQPa,b,c,d for
CY7C1470BV25, DQa,b/DQPa,b for CY7C1472BV25, and
DQa,b,c,d,e,f,g,h/DQPa,b,c,d,e,f,g,h for CY7C1474BV25) are
automatically tri-stated during the data portion of a write cycle,
regardless of the state of OE.
Burst Write Accesses
The CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25
has an on-chip burst counter that enables the user to supply a
single address and conduct up to four write operations without
reasserting the address inputs. ADV/LD must be driven LOW to
load the initial address, as described in Single Write Accesses
on page 8. When ADV/LD is driven HIGH on the subsequent
clock rise, the Chip Enables (CE1, CE2, and CE3) and WE inputs
are ignored and the burst counter is incremented. The correct
BW (BWa,b,c,d for CY7C1470BV25, BWa,b for CY7C1472BV25,
and BWa,b,c,d,e,f,g,h for CY7C1474BV25) inputs must be driven
in each cycle of the burst write to write the correct bytes of data.
Sleep Mode
The ZZ input pin is an asynchronous input. Asserting ZZ places
the SRAM in a power conservation “sleep” mode. Two clock
cycles are required to enter into or exit from this “sleep” mode.
While in this mode, data integrity is guaranteed. Accesses
pending when entering the “sleep” mode are not considered valid
nor is the completion of the operation guaranteed. The device
must be deselected before entering the “sleep” mode. CE1, CE2,
and CE3, must remain inactive for the duration of tZZREC after the
ZZ input returns LOW.
Linear Burst Address Table (MODE = GND)
First
Address
Second
Address
Third
Address
Fourth
Address
A1, A0
A1, A0
A1, A0
A1, A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
Interleaved Burst Address Table
(MODE = Floating or VDD)
First
Address
A1, A0
00
01
10
11
Second
Address
A1, A0
01
00
11
10
Third
Address
A1, A0
10
11
00
01
Fourth
Address
A1, A0
11
10
01
00
ZZ Mode Electrical Characteristics
Parameter
Description
Test Conditions
Min
Max
Unit
IDDZZ
Sleep mode standby current
ZZ  VDD 0.2 V
–
120
mA
tZZS
Device operation to ZZ
ZZVDD  0.2 V
–
2tCYC
ns
tZZREC
ZZ recovery time
ZZ  0.2 V
2tCYC
–
ns
tZZI
ZZ active to sleep current
This parameter is sampled
–
2tCYC
ns
tRZZI
ZZ Inactive to exit sleep current
This parameter is sampled
0
–
ns
Document Number: 001-15032 Rev. *I
Page 9 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Truth Table
The truth table for CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25 follows. [1, 2, 3, 4, 5, 6, 7]
Address
Used
CE
ZZ
ADV/LD
WE
BWx
OE
CEN
CLK
DQ
Deselect Cycle
None
H
L
L
X
X
X
L
L-H
Tri-State
Continue Deselect Cycle
None
X
L
H
X
X
X
L
L-H
Tri-State
Read Cycle (Begin Burst)
External
L
L
L
H
X
L
L
L-H
Data Out (Q)
Next
X
L
H
X
X
L
L
L-H
Data Out (Q)
External
L
L
L
H
X
H
L
L-H
Tri-State
Next
X
L
H
X
X
H
L
L-H
Tri-State
External
L
L
L
L
L
X
L
L-H
Data In (D)
Write Cycle (Continue Burst)
Next
X
L
H
X
L
X
L
L-H
Data In (D)
NOP/Write Abort (Begin Burst)
None
L
L
L
L
H
X
L
L-H
Tri-State
Write Abort (Continue Burst)
Next
X
L
H
X
H
X
L
L-H
Tri-State
Current
X
L
X
X
X
X
H
L-H
–
None
X
H
X
X
X
X
X
X
Tri-State
Operation
Read Cycle (Continue Burst)
NOP/Dummy Read (Begin Burst)
Dummy Read (Continue Burst)
Write Cycle (Begin Burst)
Ignore Clock Edge (Stall)
Sleep Mode
Notes
1. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for ALL Chip Enables active. BWx = L signifies at least one Byte Write Select is active, BWx = Valid
signifies that the desired Byte Write Selects are asserted, see Partial Write Cycle Description on page 11 for details.
2. Write is defined by WE and BW[a:d]. See Partial Write Cycle Description on page 11 for details.
3. When a write cycle is detected, all IOs are tri-stated, even during Byte Writes.
4. The DQ and DQP pins are controlled by the current cycle and the OE signal.
5. CEN = H inserts wait states.
6. Device powers up deselected with the IOs in a tri-state condition, regardless of OE.
7. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles.During a Read cycle DQs and DQP[a:d] = tri-state when OE is
inactive or when the device is deselected, and DQs = data when OE is active.
Document Number: 001-15032 Rev. *I
Page 10 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Partial Write Cycle Description
The partial write cycle description for CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25 follows.[8, 9, 10, 11]
Function (CY7C1470BV25)
WE
BWd
BWc
BWb
BWa
Read
H
X
X
X
X
Write – No bytes written
L
H
H
H
H
Write Byte a – (DQa and DQPa)
L
H
H
H
L
Write Byte b – (DQb and DQPb)
L
H
H
L
H
Write Bytes b, a
L
H
H
L
L
Write Byte c – (DQc and DQPc)
L
H
L
H
H
Write Bytes c, a
L
H
L
H
L
Write Bytes c, b
L
H
LL
L
H
Write Bytes c, b, a
L
H
L
L
L
Write Byte d – (DQd and DQPd)
L
L
H
H
H
Write Bytes d, a
L
L
H
H
L
Write Bytes d, b
L
L
H
L
H
Write Bytes d, b, a
L
L
H
L
L
Write Bytes d, c
L
L
L
H
H
Write Bytes d, c, a
L
L
L
H
L
Write Bytes d, c, b
L
L
L
L
H
Write All Bytes
L
L
L
L
L
Function (CY7C1472BV25)
WE
BWb
BWa
Read
H
x
x
Write – No Bytes Written
L
H
H
Write Byte a – (DQa and DQPa)
L
H
L
Write Byte b – (DQb and DQPb)
L
L
H
Write Both Bytes
L
L
L
Function (CY7C1474BV25)
WE
BWx
Read
H
x
Write – No Bytes Written
L
H
Write Byte X(DQx and DQPx)
L
L
Write All Bytes
L
All BW = L
Notes
8. X = “Don't Care”, H = Logic HIGH, L = Logic LOW, CE stands for ALL Chip Enables active. BWx = L signifies at least one Byte Write Select is active, BWx = Valid
signifies that the desired Byte Write Selects are asserted, see Partial Write Cycle Description for details.
9. Write is defined by WE and BW[a:d]. See Partial Write Cycle Description for details.
10. When a write cycle is detected, all IOs are tri-stated, even during Byte Writes.
11. Table lists only a partial listing of the Byte Write combinations. Any combination of BW[a:d] is valid. Appropriate write is based on which Byte Write is active.
Document Number: 001-15032 Rev. *I
Page 11 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
IEEE 1149.1 Serial Boundary Scan (JTAG)
The CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25
incorporates a serial boundary scan test access port (TAP). This
port operates in accordance with IEEE Standard 1149.1-1990
but does not have the set of functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because their inclusion places an added delay in the
critical speed path of the SRAM. Note that the TAP controller
functions in a manner that does not conflict with the operation of
other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 2.5 V IO logic levels.
The CY7C1470BV25, CY7C1472BV25, and CY7C1474BV25
contains a TAP controller, instruction register, boundary scan
register, bypass register, and ID register.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are
internally pulled up and may be unconnected. They may
alternately be connected to VDD through a pull up resistor. TDO
must be left unconnected. During power up, the device comes
up in a reset state, which does not interfere with the operation of
the device.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this ball unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
Test Data-In (TDI)
The TDI ball is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. For information about
loading the instruction register, see the TAP Controller State
Diagram. TDI is internally pulled up and can be unconnected if
the TAP is unused in an application. TDI is connected to the most
significant bit (MSB) of any register. (See TAP Controller Block
Diagram.)
Test Data-Out (TDO)
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current state
of the TAP state machine. The output changes on the falling edge
of TCK. TDO is connected to the least significant bit (LSB) of any
register. (See TAP Controller State Diagram.)
TAP Controller Block Diagram
TAP Controller State Diagram
1
TEST-LOGIC
RESET
0
RUN-TEST/
IDLE
0
Bypass Register
2 1 0
0
1
SELECT
DR-SCA N
1
SELECT
IR-SCAN
0
1
1
CAPTURE-DR
TDO
x . . . . . 2 1 0
SHIFT-IR
1
Selection
Circuitry
Identification Register
0
0
Instruction Register
31 30 29 . . . 2 1 0
CAPTURE-IR
0
0
Boundary Scan Register
1
EXIT1-DR
1
EXIT1-IR
0
1
0
PAUSE-DR
0
TCK
PAUSE-IR
1
0
TM S
TAP CONTROLLER
1
EXIT2-DR
0
EXIT2-IR
1
1
UPDATE-DR
1
TDI
Selection
Circuitry
0
SHIFT-DR
0
1
0
UPDATE-IR
1
0
Performing a TAP RESET
A RESET is performed by forcing TMS HIGH (VDD) for five rising
edges of TCK. This RESET does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
During power up, the TAP is reset internally to ensure that TDO
comes up in a High Z state.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Document Number: 001-15032 Rev. *I
TAP Registers
Registers are connected between the TDI and TDO balls to scan
the data in and out of the SRAM test circuitry. Only one register
can be selected at a time through the instruction register. Data is
serially loaded into the TDI ball on the rising edge of TCK. Data
is output on the TDO ball on the falling edge of TCK.
Page 12 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the TAP Controller Block Diagram on
page 12. During power up, the instruction register is loaded with
the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
When the TAP controller is in the Capture-IR state, the two least
significant bits are loaded with a binary ‘01’ pattern to enable fault
isolation of the board-level serial test data path.
Bypass Register
Instructions are loaded into the TAP controller during the Shift-IR
state when the instruction register is placed between TDI and
TDO. During this state, instructions are shifted through the
instruction register through the TDI and TDO balls. To execute
the instruction after it is shifted in, the TAP controller must be
moved into the Update-IR state.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is executed
whenever the instruction register is loaded with all 0s. EXTEST
is not implemented in this SRAM TAP controller, and therefore
this device is not compliant to 1149.1. The TAP controller does
recognize an all-0 instruction.
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This shifts the data through the SRAM with
minimal delay. The bypass register is set LOW (VSS) when the
BYPASS instruction is executed.
When an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is one difference between the
two instructions. Unlike the SAMPLE/PRELOAD instruction,
EXTEST places the SRAM outputs in a High Z state.
Boundary Scan Register
The IDCODE instruction loads a vendor-specific, 32-bit code into
the instruction register. It also places the instruction register
between the TDI and TDO balls and shifts the IDCODE out of the
device when the TAP controller enters the Shift-DR state.
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM.
The boundary scan register is loaded with the contents of the
RAM IO ring when the TAP controller is in the Capture-DR state
and is then placed between the TDI and TDO balls when the
controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used to
capture the contents of the IO ring.
The Boundary Scan Order tables show the order in which the bits
are connected. Each bit corresponds to one of the bumps on the
SRAM package. The MSB of the register is connected to TDI and
the LSB is connected to TDO.
Identification (ID) Register
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired into
the SRAM and can be shifted out when the TAP controller is in
the Shift-DR state. The ID register has a vendor code and other
information described in Identification Register Definitions on
page 16.
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in Identification
Codes on page 17. Three of these instructions are listed as
RESERVED and must not be used. The other five instructions
are described in this section in detail.
The TAP controller used in this SRAM is not fully compliant to the
1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented.
The TAP controller cannot be used to load address data or
control signals into the SRAM and cannot preload the IO buffers.
The SRAM does not implement the 1149.1 commands EXTEST
or INTEST or the PRELOAD portion of SAMPLE/PRELOAD;
rather, it performs a capture of the IO ring when these
instructions are executed.
Document Number: 001-15032 Rev. *I
IDCODE
The IDCODE instruction is loaded into the instruction register
during power up or whenever the TAP controller is in a test logic
reset state.
SAMPLE Z
The SAMPLE Z instruction connects the boundary scan register
between the TDI and TDO pins when the TAP controller is in a
Shift-DR state. It also places all SRAM outputs into a High Z
state.
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. The
PRELOAD portion of this instruction is not implemented, so the
device TAP controller is not fully 1149.1 compliant.
When the SAMPLE/PRELOAD instruction is loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and bidirectional balls is
captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 20 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because there
is a large difference in the clock frequencies, it is possible that
during the Capture-DR state, an input or output may undergo a
transition. The TAP may then try to capture a signal while in
transition (metastable state). This does not harm the device, but
there is no guarantee as to the value that is captured.
Repeatable results may not be possible.
To guarantee that the boundary scan register captures the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture setup plus hold
time (tCS plus tCH).
The SRAM clock input might not be captured correctly if there is
no way in a design to stop (or slow) the clock during a
SAMPLE/PRELOAD instruction. If this is an issue, it is still
Page 13 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
possible to capture all other signals and simply ignore the value
of the CLK captured in the boundary scan register.
BYPASS
When the BYPASS instruction is loaded in the instruction register
and the TAP is placed in a Shift-DR state, the bypass register is
placed between the TDI and TDO balls. The advantage of the
BYPASS instruction is that it shortens the boundary scan path
when multiple devices are connected together on a board.
After the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the boundary
scan register between the TDI and TDO balls.
Note that since the PRELOAD part of the command is not
implemented, putting the TAP to the Update-DR state while
performing a SAMPLE/PRELOAD instruction has the same
effect as the Pause-DR command.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
TAP Timing
1
2
Test Clock
(TCK )
3
t TH
t TM SS
t TM SH
t TDIS
t TDIH
t
TL
4
5
6
t CY C
Test M ode Select
(TM S)
Test Data-In
(TDI)
t TDOV
t TDOX
Test Data-Out
(TDO)
DON’T CA RE
Document Number: 001-15032 Rev. *I
UNDEFINED
Page 14 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
TAP AC Switching Characteristics
Over the Operating Range [12, 13]
Parameter
Description
Min
Max
Unit
Clock
tTCYC
TCK Clock Cycle Time
50
–
ns
tTF
TCK Clock Frequency
–
20
MHz
tTH
TCK Clock HIGH time
20
–
ns
tTL
TCK Clock LOW time
20
–
ns
Output Times
tTDOV
TCK Clock LOW to TDO Valid
–
10
ns
tTDOX
TCK Clock LOW to TDO Invalid
0
–
ns
tTMSS
TMS Setup to TCK Clock Rise
5
–
ns
tTDIS
TDI Setup to TCK Clock Rise
5
–
ns
tCS
Capture Setup to TCK Rise
5
–
ns
tTMSH
TMS Hold after TCK Clock Rise
5
–
ns
tTDIH
TDI Hold after Clock Rise
5
–
ns
tCH
Capture Hold after Clock Rise
5
–
ns
Setup Times
Hold Times
Notes
12. tCS and tCH refer to the setup and hold time requirements of latching data from the boundary scan register.
13. Test conditions are specified using the load in TAP AC Test Conditions. tR/tF = 1 ns.
Document Number: 001-15032 Rev. *I
Page 15 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
2.5 V TAP AC Test Conditions
2.5 V TAP AC Output Load Equivalent
Input pulse levels................................................VSS to 2.5 V
1.25V
Input rise and fall time .....................................................1 ns
Input timing reference levels........................................ 1.25 V
50Ω
Output reference levels ............................................... 1.25 V
TDO
Test load termination supply voltage ........................... 1.25 V
Z O= 50Ω
20pF
TAP DC Electrical Characteristics and Operating Conditions
(0 °C < TA < +70 °C; VDD = 2.5 V ± 0.125 V unless otherwise noted)[14]
Parameter
Description
Test Conditions
Min
Max
Unit
VOH1
Output HIGH Voltage
IOH = –1.0 mA, VDDQ = 2.5 V
1.7
–
V
VOH2
Output HIGH Voltage
IOH = –100 A, VDDQ = 2.5 V
2.1
–
V
VOL1
Output LOW Voltage
IOL = 1.0 mA, VDDQ = 2.5 V
–
0.4
V
VOL2
Output LOW Voltage
IOL = 100 A, VDDQ = 2.5 V
–
0.2
V
VIH
Input HIGH Voltage
VDDQ = 2.5 V
1.7
VDD + 0.3
V
VIL
Input LOW Voltage
VDDQ = 2.5 V
–0.3
0.7
V
IX
Input Load Current
GND  VI  VDDQ
–5
5
A
Identification Register Definitions
Instruction Field
Revision Number (31:29)
Device Depth (28:24)
Architecture/Memory Type (23:18)
Bus Width/Density (17:12)
Cypress JEDEC ID Code (11:1)
ID Register Presence Indicator (0)
CY7C1470BV25
(2 M × 36)
CY7C1472BV25
(4 M × 18)
CY7C1474BV25
(1 M × 72)
Description
000
000
000
01011
01011
01011
001000
001000
001000
Defines
memory
architecture
Defines width and density
100100
010100
110100
00000110100
00000110100
00000110100
1
1
1
Describes the version number
Reserved for internal use
Allows unique
SRAM vendor
type
identification
and
of
Indicates the presence of an ID
register
Scan Register Sizes
Register Name
Bit Size (× 36)
Bit Size (× 18)
Bit Size (× 72)
Instruction
3
3
3
Bypass
1
1
1
ID
32
32
32
Boundary Scan Order–165-ball FBGA
71
52
–
Boundary Scan Order–209-ball BGA
–
–
110
Note
14. All voltages refer to VSS (GND).
Document Number: 001-15032 Rev. *I
Page 16 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Identification Codes
Instruction
Code
Description
EXTEST
000
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM outputs to High Z state. This instruction is not 1149.1-compliant.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and TDO. This
operation does not affect SRAM operations.
SAMPLE Z
010
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High Z state.
RESERVED
011
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
100
Captures IO ring contents. Places the boundary scan register between TDI and TDO.
Does not affect SRAM operation. This instruction does not implement 1149.1 preload function and
is therefore not 1149.1-compliant.
RESERVED
101
Do Not Use: This instruction is reserved for future use.
RESERVED
110
Do Not Use: This instruction is reserved for future use.
BYPASS
111
Places the bypass register between TDI and TDO. This operation does not affect SRAM operations.
Boundary Scan Exit Order (2 M × 36)
Bit #
165-ball ID
Bit #
165-ball ID
Bit #
165-ball ID
Bit #
165-ball ID
1
C1
21
R3
41
J11
61
B7
2
D1
22
P2
42
K10
62
B6
3
E1
23
R4
43
J10
63
A6
4
D2
24
P6
44
H11
64
B5
5
E2
25
R6
45
G11
65
A5
6
F1
26
R8
46
F11
66
A4
7
G1
27
P3
47
E11
67
B4
8
F2
28
P4
48
D10
68
B3
9
G2
29
P8
49
D11
69
A3
10
J1
30
P9
50
C11
70
A2
11
K1
31
P10
51
G10
71
B2
12
L1
32
R9
52
F10
13
J2
33
R10
53
E10
14
M1
34
R11
54
A9
15
N1
35
N11
55
B9
16
K2
36
M11
56
A10
17
L2
37
L11
57
B10
18
M2
38
M10
58
A8
19
R1
39
L10
59
B8
20
R2
40
K11
60
A7
Document Number: 001-15032 Rev. *I
Page 17 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Boundary Scan Exit Order (4 M × 18)
Bit #
165-ball ID
Bit #
165-ball ID
Bit #
165-ball ID
Bit #
165-ball ID
1
D2
14
R4
2
E2
15
P6
27
L10
40
B10
28
K10
41
A8
3
F2
16
R6
4
G2
17
R8
29
J10
42
B8
30
H11
43
A7
5
J1
18
6
K1
19
P3
31
G11
44
B7
P4
32
F11
45
B6
7
L1
8
M1
20
P8
33
E11
46
A6
21
P9
34
D11
47
B5
9
N1
22
P10
35
C11
48
A4
10
R1
23
R9
36
A11
49
B3
11
R2
24
R10
37
A9
50
A3
12
R3
25
R11
38
B9
51
A2
13
P2
26
M10
39
A10
52
B2
Boundary Scan Exit Order (1 M × 72)
Bit #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
209-ball ID
A1
A2
B1
B2
C1
C2
D1
D2
E1
E2
F1
F2
G1
G2
H1
H2
J1
J2
L1
L2
M1
M2
Bit #
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
209-ball ID
T1
T2
U1
U2
V1
V2
W1
W2
T6
V3
V4
U4
W5
V6
W6
V5
U5
U6
W7
V7
U7
V8
Bit #
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
209-ball ID
U10
T11
T10
R11
R10
P11
P10
N11
N10
M11
M10
L11
L10
P6
J11
J10
H11
H10
G11
G10
F11
F10
Bit #
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
209-ball ID
B11
B10
A11
A10
A7
A5
A9
U8
A6
D6
K6
B6
K3
A8
B4
B3
C3
C4
C8
C9
B9
B8
23
24
25
26
27
28
N1
N2
P1
P2
R2
R1
51
52
53
54
55
56
V9
W11
W10
V11
V10
U11
79
80
81
82
83
84
E10
E11
D11
D10
C11
C10
107
108
109
110
A4
C6
B7
A3
Document Number: 001-15032 Rev. *I
Page 18 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Maximum Ratings
Current into Outputs (LOW)......................................... 20 mA
Exceeding maximum ratings may impair the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................ –65 °C to +150 °C
Static Discharge Voltage......................................... > 2001 V
(MIL-STD-883, Method 3015)
Latch up Current.................................................... > 200 mA
Operating Range
Ambient Temperature with
Power Applied .......................................... –55 °C to +125 °C
Supply Voltage on VDD Relative to GND ......–0.5 V to +3.6 V
Range
Supply Voltage on VDDQ Relative to GND ..... –0.5 V to +VDD
Commercial
DC to Outputs in Tri-State..................–0.5 V to VDDQ + 0.5 V
Industrial
Ambient
Temperature
VDD
VDDQ
0 °C to +70 °C 2.5 V – 5% / +5% 2.5 V – 5% to
VDD
–40 °C to +85 °C
DC Input Voltage ................................. –0.5 V to VDD + 0.5 V
Electrical Characteristics
Over the Operating Range[15, 16]
Parameter
Description
Test Conditions
VDD
Power Supply Voltage
VDDQ
IO Supply Voltage
For 2.5 V IO
VOH
Output HIGH Voltage
For 2.5 V IO, IOH =1.0 mA
VOL
Output LOW Voltage
For 2.5 V IO, IOL =1.0 mA
Min
Max
Unit
2.375
2.625
V
2.375
VDD
V
2.0
–
V
–
0.4
V
Input HIGH
Voltage[15]
For 2.5 V IO
1.7
VDD + 0.3 V
V
VIL
Input LOW
Voltage[15]
For 2.5 V IO
–0.3
0.7
V
IX
Input Leakage Current
except ZZ and MODE
GND  VI  VDDQ
–5
5
A
Input Current of MODE
Input = VSS
–30
–
A
Input = VDD
–
5
A
Input = VSS
–5
–
A
Input = VDD
–
30
A
Output Leakage Current GND  VI  VDDQ, Output Disabled
–5
5
A
VDD Operating Supply
4.0-ns cycle, 250 MHz
–
450
mA
5.0-ns cycle, 200 MHz
–
450
mA
6.0-ns cycle, 167 MHz
–
400
mA
Automatic CE
Power Down
Current—TTL Inputs
Max. VDD, Device Deselected, 4.0-ns cycle, 250MHz
VIN  VIH or VIN  VIL,
5.0-ns cycle, 200 MHz
f = fMAX = 1/tCYC
6.0-ns cycle, 167 MHz
–
200
mA
–
200
mA
–
200
mA
Automatic CE
Power Down
Current—CMOS Inputs
Max. VDD, Device Deselected, All speed grades
VIN  0.3 V or
VIN > VDDQ 0.3 V, f = 0
–
120
mA
VIH
Input Current of ZZ
IOZ
IDD
[17]
ISB1
ISB2
VDD = Max, IOUT = 0 mA,
f = fMAX = 1/tCYC
Notes
15. Overshoot: VIH(AC) < VDD +1.5 V (pulse width less than tCYC/2). Undershoot: VIL(AC) > –2 V (pulse width less than tCYC/2).
16. TPower-up: assumes a linear ramp from 0 V to VDD (min.) within 200 ms. During this time VIH < VDD and VDDQ < VDD.
17. The operation current is calculated with 50% read cycle and 50% write cycle.
Document Number: 001-15032 Rev. *I
Page 19 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Electrical Characteristics (continued)
Over the Operating Range[15, 16] (continued)
Parameter
ISB3
ISB4
Description
Test Conditions
Min
Max
Unit
Automatic CE
Power Down
Current—CMOS Inputs
Max. VDD, Device Deselected, 4.0-ns cycle, 250 MHz
VIN  0.3 V or
5.0-ns cycle, 200 MHz
VIN > VDDQ 0.3 V,
f = fMAX = 1/tCYC
6.0-ns cycle, 167 MHz
–
200
mA
–
200
mA
–
200
mA
Automatic CE
Power Down
Current—TTL Inputs
Max. VDD, Device Deselected, All speed grades
VIN  VIH or VIN  VIL, f = 0
–
135
mA
Capacitance
Tested initially and after any design or process changes that may affect these parameters.
Parameter
Description
Test Conditions
CADDRESS
Address Input Capacitance
CDATA
Data Input Capacitance
CCTRL
Control Input Capacitance
CCLK
Clock Input Capacitance
CIO
Input/Output Capacitance
100-pin TQFP 165-ball FBGA 209-ball FBGA Unit
Max
Max
Max
TA = 25 °C, f = 1 MHz,
VDD = 2.5 V
VDDQ = 2.5 V
6
6
6
pF
5
5
5
pF
8
8
8
pF
6
6
6
pF
5
5
5
pF
Thermal Resistance
Tested initially and after any design or process changes that may affect these parameters.
Parameter
Description
JA
Thermal Resistance
(Junction to Ambient)
JC
Thermal Resistance
(Junction to Case)
Test Conditions
100-pin TQFP 165-ball FBGA 209-ball FBGA Unit
Package
Package
Package
Test conditions follow
standard test methods and
procedures for measuring
thermal impedance, per
EIA/JESD51.
24.63
16.3
15.2
C/W
2.28
2.1
1.7
C/W
AC Test Loads and Waveforms
2.5 V IO Test Load
R = 1667 
2.5 V
OUTPUT
OUTPUT
RL = 50 
Z0 = 50 
GND
5 pF
R = 1538 
VL = 1.25 V
(a)
Document Number: 001-15032 Rev. *I
ALL INPUT PULSES
VDDQ
INCLUDING
JIG AND
SCOPE
(b)
10%
90%
10%
90%
 1 ns
 1 ns
(c)
Page 20 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Switching Characteristics
Over the Operating Range[18, 19]
Parameter
tPower[20]
Description
VCC (typical) to the First Access Read or Write
250 MHz
200 MHz
167 MHz
Unit
Min
Max
Min
Max
Min
Max
1
–
1
–
1
–
ms
4.0
–
5.0
–
6.0
–
ns
–
250
–
200
–
167
MHz
Clock
tCYC
Clock Cycle Time
FMAX
Maximum Operating Frequency
tCH
Clock HIGH
2.0
–
2.0
–
2.2
–
ns
tCL
Clock LOW
2.0
–
2.0
–
2.2
–
ns
Output Times
tCO
Data Output Valid After CLK Rise
–
3.0
–
3.0
–
3.4
ns
tOEV
OE LOW to Output Valid
–
3.0
–
3.0
–
3.4
ns
tDOH
Data Output Hold After CLK Rise
1.3
–
1.3
–
1.5
–
ns
tCHZ
Clock to High Z[21, 22, 23]
–
3.0
–
3.0
–
3.4
ns
tCLZ
Z[21, 22, 23]
1.3
–
1.3
–
1.5
–
ns
–
3.0
–
3.0
–
3.4
ns
0
–
0
–
0
–
ns
tEOHZ
tEOLZ
Clock to Low
OE HIGH to Output High
OE LOW to Output Low
Z[21, 22, 23]
Z[21, 22, 23]
Setup Times
tAS
Address Setup Before CLK Rise
1.4
–
1.4
–
1.5
–
ns
tDS
Data Input Setup Before CLK Rise
1.4
–
1.4
–
1.5
–
ns
tCENS
CEN Setup Before CLK Rise
1.4
–
1.4
–
1.5
–
ns
tWES
WE, BWx Setup Before CLK Rise
1.4
–
1.4
–
1.5
–
ns
tALS
ADV/LD Setup Before CLK Rise
1.4
–
1.4
–
1.5
–
ns
tCES
Chip Select Setup
1.4
–
1.4
–
1.5
–
ns
tAH
Address Hold After CLK Rise
0.4
–
0.4
–
0.5
–
ns
tDH
Data Input Hold After CLK Rise
0.4
–
0.4
–
0.5
–
ns
tCENH
CEN Hold After CLK Rise
0.4
–
0.4
–
0.5
–
ns
tWEH
WE, BWx Hold After CLK Rise
0.4
–
0.4
–
0.5
–
ns
tALH
ADV/LD Hold after CLK Rise
0.4
–
0.4
–
0.5
–
ns
tCEH
Chip Select Hold After CLK Rise
0.4
–
0.4
–
0.5
–
ns
Hold Times
Notes
18. Timing reference is 1.25 V when VDDQ = 2.5 V.
19. Test conditions shown in (a) of AC Test Loads and Waveforms on page 20 unless otherwise noted.
20. This part has a voltage regulator internally; tpower is the time power is supplied above VDD minimum initially, before a read or write operation can be initiated.
21. tCHZ, tCLZ, tEOLZ, and tEOHZ are specified with AC test conditions shown in (b) of AC Test Loads and Waveforms on page 20. Transition is measured ±200 mV from
steady-state voltage.
22. At any supplied voltage and temperature, tEOHZ is less than tEOLZ and tCHZ is less than tCLZ to eliminate bus contention between SRAMs when sharing the same data
bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed to achieve
High Z before Low Z under the same system conditions.
23. This parameter is sampled and not 100% tested.
Document Number: 001-15032 Rev. *I
Page 21 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Switching Waveforms
Figure 2 shows read-write timing waveform.[24, 25, 26]
Figure 2. Read/Write Timing
1
2
3
t CYC
4
5
6
A3
A4
7
8
9
A5
A6
10
CLK
t CENS
t CENH
t CES
t CEH
t CH
t CL
CEN
CE
ADV/LD
WE
BW x
A1
ADDRESS
A2
A7
t CO
t AS
t DS
t AH
Data
t DH
D(A1)
t CLZ
D(A2)
D(A2+1)
t DOH
Q(A3)
t OEV
Q(A4)
t CHZ
Q(A4+1)
D(A5)
Q(A6)
In-Out (DQ)
t OEHZ
t DOH
t OELZ
OE
WRITE
D(A1)
WRITE
D(A2)
BURST
WRITE
D(A2+1)
READ
Q(A3)
DON’T CARE
READ
Q(A4)
BURST
READ
Q(A4+1)
WRITE
D(A5)
READ
Q(A6)
WRITE
D(A7)
DESELECT
UNDEFINED
Notes
24. For this waveform ZZ is tied LOW.
25. When CE is LOW, CE1 is LOW, CE2 is HIGH, and CE3 is LOW. When CE is HIGH,CE1 is HIGH, CE2 is LOW, or CE3 is HIGH.
26. Order of the Burst sequence is determined by the status of the MODE (0 = Linear, 1 = Interleaved).Burst operations are optional.
Document Number: 001-15032 Rev. *I
Page 22 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Switching Waveforms (continued)
[27, 28, 29]
Figure 3 shows NOP, STALL and DESELECT Cycles waveform.
Figure 3. NOP, STALL and DESELECT Cycles
1
2
A1
A2
3
4
5
A3
A4
6
7
8
9
10
CLK
CEN
CE
ADV/LD
WE
BWx
ADDRESS
A5
t CHZ
D(A1)
Data
Q(A2)
D(A4)
Q(A3)
Q(A5)
In-Out (DQ)
WRITE
D(A1)
READ
Q(A2)
STALL
READ
Q(A3)
WRITE
D(A4)
STALL
DON’T CARE
Figure 4 shows ZZ Mode timing waveform.
NOP
READ
Q(A5)
DESELECT
CONTINUE
DESELECT
UNDEFINED
[30, 31]
Figure 4. ZZ Mode Timing
CLK
t
ZZ
I
t
t
ZZ
ZZREC
ZZI
SUPPLY
I
t RZZI
DDZZ
A LL INPUTS
(except ZZ)
Outputs (Q)
DESELECT or READ Only
High-Z
DON’T CARE
Notes
27. For this waveform ZZ is tied LOW.
28. When CE is LOW, CE1 is LOW, CE2 is HIGH, and CE3 is LOW. When CE is HIGH,CE1 is HIGH, CE2 is LOW, or CE3 is HIGH.
29. The IGNORE CLOCK EDGE or STALL cycle (Clock 3) illustrated CEN being used to create a pause. A write is not performed during this cycle.
30. Device must be deselected when entering ZZ mode. See Truth Table on page 10 for all possible signal conditions to deselect the device.
31. IOs are in High Z when exiting ZZ sleep mode.
Document Number: 001-15032 Rev. *I
Page 23 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Ordering Information
Cypress offers other versions of this type of product in many different configurations and features. The below table contains only the
list of parts that are currently available. For a complete listing of all options, visit the Cypress website at www.cypress.com and refer
to the product summary page at http://www.cypress.com/products or contact your local sales representative. Cypress maintains a
worldwide network of offices, solution centers, manufacturer’s representatives and distributors. To find the office closest to you, visit
us at t http://www.cypress.com/go/datasheet/offices.
Speed
(MHz)
167
200
Ordering Code
Package
Diagram
Part and Package Type
Operating
Range
CY7C1470BV25-167AXC
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
Commercial
CY7C1470BV25-167BZXI
51-85165 165-ball Fine-Pitch Ball Grid Array (15 × 17 × 1.4 mm) Pb-free
CY7C1470BV25-200AXC
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
Commercial
51-85165 165-ball Fine-Pitch Ball Grid Array (15 × 17 × 1.4 mm) Pb-free
Commercial
51-85050 100-pin Thin Quad Flat Pack (14 × 20 × 1.4 mm) Pb-free
Commercial
Industrial
CY7C1472BV25-200AXC
CY7C1470BV25-200BZXC
CY7C1470BV25-200BZXI
250
CY7C1470BV25-250AXC
Industrial
Ordering Code Definitions
CY 7C 147X B V25 - XXX XX X X
X = T or blank
T = Tape and Reel; blank = Tube
Temperature Range: X = C or I
C = Commercial; I = Industrial
Package Type:
AX = 100-pin TQFP (Pb-free)
BZX = 165-ball FBGA (Pb-free)
Frequency Range: XXX = 167 MHz or 200 MHz or 250 MHz
VDD = 2.5 V
Process Technology
147X = 1470 or 1472 or 1474
1470 = PL, 2Mb x 36 (72Mb)
1472 = PL, 4Mb x 18 (72Mb)
1474 = PL, 1Mb x 72 (72Mb)
Marketing Code: 7C = SRAMs
Company ID: CY = Cypress
Document Number: 001-15032 Rev. *I
Page 24 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Package Diagrams
Figure 5. 100-pin TQFP (14 × 20 × 1.4 mm), 51-85050
51-85050 *D
Document Number: 001-15032 Rev. *I
Page 25 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Package Diagrams (continued)
Figure 6. 165-ball FBGA (15 × 17 × 1.4 mm), 51-85165
51-85165 *B
Document Number: 001-15032 Rev. *I
Page 26 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Acronyms
Document Conventions
Acronym
Description
Units of Measure
BGA
ball grid array
CMOS
complementary metal oxide semiconductor
°C
degree Celcius
FBGA
fine-pitch ball grid array
µA
micro Amperes
I/O
input/output
mA
milli Amperes
JTAG
Joint Test Action Group
mm
milli meter
LSB
least significant bit
ms
milli seconds
MSB
most significant bit
MHz
Mega Hertz
OE
output enable
ns
nano seconds
SRAM
static random access memory

Ohms
TAP
test access port
%
percent
TCK
test clock
pF
pico Farad
TDI
test data-in
V
Volts
TDO
test data-out
W
Watts
TMS
test mode select
TQFP
thin quad flat pack
TTL
transistor transistor logic
WE
write enable
Document Number: 001-15032 Rev. *I
Symbol
Unit of Measure
Page 27 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Document History Page
Document Title: CY7C1470BV25/CY7C1472BV25/CY7C1474BV25, 72-Mbit (2 M × 36/4 M × 18/1 M × 72) Pipelined SRAM with
NoBL™ Architecture
Document Number: 001-15032
REV.
ECN No. Issue Date Orig. of Change
Description of Change
**
1032642
See ECN
VKN/KKVTMP
*A
1562503
See ECN
VKN/AESA
New data sheet
Removed 1.8V IO offering from the data sheet
Added footnote 14 related to IDD
*B
1897447
See ECN
VKN/AESA
*C
2082487
See ECN
VKN
*D
2159486
See ECN
VKN/PYRS
*E
2898663 03/24/2010
NJY
Removed inactive parts from Ordering Information table; Updated package
diagram.
*F
2905460 04/06/2010
VKN
Removed inactive part numbers
CY7C1470BV25-167BZC,CY7C1470BV25-167BZI,
CY7C1470BV25-167BZXC,CY7C1470BV25-200BZC,
CY7C1472BV25-250BZC,CY7C1474BV25-167BGC,
CY7C1474BV25-167BGI,
CY7C1474BV25-200BGC,CY7C1474BV25-200BGI,
CY7C1474BV25-200BGXI,from the ordering information table.
*G
3061663 10/15/2010
NJY
Removed pruned parts CY7C1472BV25-200BZI, CY7C1472BV25-200BZIT
from ordering information table. Removed associated package. Added
Ordering Code Definitions, sales links, and TOC.
*H
3207526 03/28/2011
NJY
Updated Ordering Information.
Updated Package Diagrams.
Updated in new template.
*I
3257192 05/14/2011
NJY
Updated Ordering Information.
Added Acronyms and Units of Measure.
Document Number: 001-15032 Rev. *I
Converted from preliminary to final
Minor Change-Moved to the external web
Page 28 of 29
[+] Feedback
CY7C1470BV25
CY7C1472BV25, CY7C1474BV25
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
Products
Automotive
Clocks & Buffers
Interface
Lighting & Power Control
PSoC Solutions
cypress.com/go/automotive
cypress.com/go/clocks
psoc.cypress.com/solutions
cypress.com/go/interface
PSoC 1 | PSoC 3 | PSoC 5
cypress.com/go/powerpsoc
cypress.com/go/plc
Memory
Optical & Image Sensing
cypress.com/go/memory
cypress.com/go/image
PSoC
cypress.com/go/psoc
Touch Sensing
cypress.com/go/touch
USB Controllers
Wireless/RF
cypress.com/go/USB
cypress.com/go/wireless
© Cypress Semiconductor Corporation, 2007-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document Number: 001-15032 Rev. *I
Revised May 17, 2011
Page 29 of 29
NoBL and No Bus Latency are trademarks of Cypress Semiconductor Corporation. ZBT is a trademark of Integrated Device Technology, Inc. All products and company names mentioned in this
document may be the trademarks of their respective holders.
[+] Feedback