Revised January 2005 MM74HC00 Quad 2-Input NAND Gate General Description Features The MM74HC00 NAND gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard CMOS integrated circuits. All gates have buffered outputs. All devices have high noise immunity and the ability to drive 10 LS-TTL loads. The 74HC logic family is functionally as well as pin-out compatible with the standard 74LS logic family. All inputs are protected from damage due to static discharge by internal diode clamps to VCC and ground. ■ Typical propagation delay: 8 ns ■ Wide power supply range: 2–6V ■ Low quiescent current: 20 µA maximum (74HC Series) ■ Low input current: 1 µA maximum ■ Fanout of 10 LS-TTL loads Ordering Code: Order Number Package Package Description Number MM74HC00M M14A MM74HC00MX_NL M14A 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Pb-Free 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow MM74HC00SJ M14D Pb-Free 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide MM74HC00MTC MTC14 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide MM74HC00MTCX_NL MTC14 Pb-Free 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide MM74HC00N N14A 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide MM74HC00N_NL N14A Pb-Free 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Pb-Free package per JEDEC J-STD-020B. Connection Diagram Logic Diagram Pin Assignments for DIP, SOIC, SOP and TSSOP Top View © 2005 Fairchild Semiconductor Corporation DS005292 www.fairchildsemi.com MM74HC00 Quad 2-Input NAND Gate September 1983 MM74HC00 Absolute Maximum Ratings(Note 1) Recommended Operating Conditions (Note 2) −0.5 to +7.0V Supply Voltage (VCC) DC Input Voltage (VIN) −1.5 to VCC+1.5V DC Output Voltage (VOUT) −0.5 to VCC+0.5V Clamp Diode Current (IIK, IOK) ±20 mA DC Output Current, per pin (IOUT) ±25 mA DC VCC or GND Current, per pin (ICC) ±50 mA Max Units 2 6 V DC Input or Output Voltage 0 VCC V −40 +85 °C (VIN, VOUT) Operating Temperature Range (TA) Input Rise or Fall Times −65°C to +150°C Storage Temperature Range (TSTG) Min Supply Voltage (VCC) (tr, tf) VCC = 2V Power Dissipation (PD) (Note 3) 600 mW S.O. Package only 500 mW Symbol VIH VIL VOH Parameter Conditions ns VCC = 6.0V 400 ns Note 2: Unless otherwise specified all voltages are referenced to ground. 260°C DC Electrical Characteristics ns 500 Note 1: Absolute Maximum Ratings are those values beyond which damage to the device may occur. Lead Temperature (TL) (Soldering 10 seconds) 1000 VCC = 4.5V Note 3: Power Dissipation temperature derating — plastic “N” package: − 12 mW/°C from 65°C to 85°C. (Note 4) TA = 25°C VCC Typ TA = −40 to 85°C TA = −55 to 125°C Guaranteed Limits Units Minimum HIGH Level 2.0V 1.5 1.5 1.5 V Input Voltage 4.5V 3.15 3.15 3.15 V 6.0V 4.2 4.2 4.2 V Maximum LOW Level 2.0V 0.5 0.5 0.5 V Input Voltage 4.5V 1.35 1.35 1.35 V 6.0V 1.8 1.8 1.8 V Minimum HIGH Level VIN = VIH or VIL Output Voltage |IOUT| ≤ 20 µA 2.0V 2.0 1.9 1.9 1.9 V 4.5V 4.5 4.4 4.4 4.4 V 6.0V 6.0 5.9 5.9 5.9 V |IOUT| ≤ 4.0 mA 4.5V 4.2 3.98 3.84 3.7 V |IOUT| ≤ 5.2 mA 6.0V 5.7 5.48 5.34 5.2 V VIN = VIH or VIL VOL Maximum LOW Level VIN = VIH Output Voltage |IOUT| ≤ 20 µA 2.0V 0 0.1 0.1 0.1 V 4.5V 0 0.1 0.1 0.1 V 6.0V 0 0.1 0.1 0.1 V V VIN = VIH IIN |IOUT| ≤ 4.0 mA 4.5V 0.2 0.26 0.33 0.4 |IOUT| ≤ 5.2 mA 6.0V 0.2 0.26 0.33 0.4 V VIN = VCC or GND 6.0V ±0.1 ±1.0 ±1.0 µA Maximum Quiescent VIN = VCC or GND 6.0V 2.0 20 40 µA Supply Current IOUT = 0 µA Maximum Input Current ICC Note 4: For a power supply of 5V ±10% the worst case output voltages (VOH, and VOL) occur for HC at 4.5V. Thus the 4.5V values should be used when designing with this supply. Worst case VIH and VIL occur at VCC = 5.5V and 4.5V respectively. (The VIH value at 5.5V is 3.85V.) The worst case leakage current (IIN, ICC, and IOZ) occur for CMOS at the higher voltage and so the 6.0V values should be used. www.fairchildsemi.com 2 VCC = 5V, TA = 25°C, CL = 15 pF, tr = tf = 6 ns Symbol tPHL, tPLH Parameter Conditions Typ Maximum Propagation 8 Guaranteed Limit Units 15 ns Delay AC Electrical Characteristics VCC = 2.0V to 6.0V, CL = 50 pF, tr = tf = 6 ns (unless otherwise specified) Symbol Parameter Conditions tPHL, tPLH Maximum Propagation Delay tTLH, tTHL Maximum Output Rise and Fall Time VCC Power Dissipation TA = −40 to 85°C TA = −55 to 125°C Guaranteed Limits Units 2.0V 45 90 113 134 4.5V 9 18 23 27 ns 6.0V 8 15 19 23 ns 2.0V 30 75 95 110 ns 4.5V 8 15 19 22 ns 7 13 16 19 6.0V CPD TA = 25°C Typ (per gate) 20 ns ns pF Capacitance (Note 5) CIN Maximum Input 5 10 10 10 pF Capacitance Note 5: CPD determines the no load dynamic power consumption, PD = CPD VCC2 f + ICC VCC, and the no load dynamic current consumption, IS = CPD VCC f + ICC. 3 www.fairchildsemi.com MM74HC00 AC Electrical Characteristics MM74HC00 Physical Dimensions inches (millimeters) unless otherwise noted 14-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-012, 0.150" Narrow Package Number M14A www.fairchildsemi.com 4 MM74HC00 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Pb-Free 14-Lead Small Outline Package (SOP), EIAJ TYPE II, 5.3mm Wide Package Number M14D 5 www.fairchildsemi.com MM74HC00 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide Package Number MTC14 www.fairchildsemi.com 6 MM74HC00 Quad 2-Input NAND Gate Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 14-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide Package Number N14A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 7 www.fairchildsemi.com