IDT IDT54FCT861B High-performance cmos bus transceiver Datasheet


IDT54/74FCT861A/B
IDT54/74FCT863A/B
HIGH-PERFORMANCE
CMOS BUS
TRANSCEIVERS
Integrated Device Technology, Inc.
FEATURES:
DESCRIPTION:
• Equivalent to AMD’s Am29861-64 bipolar registers in
pinout/function, speed and output drive over full temperature and voltage supply extremes
• IDT54/74FCT861A/863A equivalent to FAST speed
• IDT54/74FCT861B/863B 25% faster than FAST
• High-speed symmetrical bidirectional transceivers
• IOL = 48mA (commercial) and 32mA (military)
• Clamp diodes on all inputs for ringing suppression
• CMOS power levels (1mW typ. static)
• TTL input and output level compatible
• CMOS output level compatible
• Substantially lower input current levels than AMD’s
bipolar Am29800 Series (5µA max.)
• Product available in Radiation Tolerant and Radiation
Enhanced versions
• Military product compliant to MIL-STD-883, Class B
The IDT54/74FCT800 series is built using an advanced
dual metal CMOS technology.
The IDT54/74FCT860 series bus transceivers provide
high-performance bus interface buffering for wide
data/address paths or buses carrying parity. The
IDT54/74FCT863 9-bit transceivers have NAND-ed output
enables for maximum control flexibility.
All of the IDT54/74FCT800 high-performance interface
family are designed for high-capacitance load drive capability
while providing low-capacitance bus loading at both inputs
and outputs. All inputs have clamp diodes and all outputs are
designed for low-capacitance bus loading in the high- impedance state.
FUNCTIONAL BLOCK DIAGRAMS
IDT54/74FCT861
IDT54/74FCT863
T0
T1 - T 9
OER
T0
T1 - T 8
OER 1
OER 2
R0
R1 - R 9
OET
R0
R1 - R 8
OET 1
OET 2
2610 drw 01
PRODUCT SELECTOR GUIDE
Device
Non-inverting
10-Bit
9-Bit
IDT54/74FCT861
IDT54/74FCT863
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
FAST is a trademark of National Semiconductor Co.
MILITARY AND COMMERCIAL TEMPERATURE RANGES
1994 Integrated Device Technology, Inc.
7.23
APRIL 1994
DSC-4620/3
1
IDT54/74FCT861A/B, IDT54/74FCT863A/B
HIGH-PERFORMANCE CMOS BUS TRANSCEIVERS
MILITARY AND COMMERCIAL TEMPERATURE RANGES
PIN CONFIGURATIONS
R1
R0
OER
NC
Vcc
T0
T1
IDT54/74FCT861 10-BIT TRANSCEIVERS
INDEX
1
24
2
23
3
22
P24-1,
D24-1,
E24-1
&
SO24-2
4
5
6
7
21
20
19
18
8
17
9
16
10
15
11
14
12
13
Vcc
T0
T1
T2
T3
T4
T5
T6
T7
T8
T9
OET
4
R2
R3
R4
NC
R5
R6
R7
3
2
28 27 26
5
25
1
6
24
7
L28-1
8
23
22
9
21
10
20
11
19
12 13 14 15 16 17 18
T2
T3
T4
NC
T5
T6
T7
R8
R9
GND
NC
OET
T9
T8
OER
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
GND
DIP/CERPACK/SOIC
TOP VIEW
LCC
TOP VIEW
R1
R0
OER
NC
Vcc
T0
T1
IDT54/74FCT863 9-BIT TRANSCEIVERS
INDEX
1
24
2
23
3
22
4
5
6
7
8
P24-1,
D24-1,
E24-1
&
SO24-2
21
20
19
18
17
9
16
10
15
11
14
12
13
Vcc
T0
T1
T2
T3
T4
T5
T6
T7
T8
OET 2
OET 1
4
R2
5
R3
R4
NC
R5
R6
R7
6
3
2
28 27 26
1
25
24
7
L28-1
8
23
22
9
21
10
20
11
19
12 13 14 15 16 17 18
R8
OER 2
GND
NC
OET 1
OET 2
T8
OER 1
R0
R1
R2
R3
R4
R5
R6
R7
R8
OER 2
GND
DIP/CERPACK/SOIC
TOP VIEW
T2
T3
T4
NC
T5
T6
T7
2610 drw 02
LCC
TOP VIEW
LOGIC SYMBOLS
IDT54/74FCT861
IDT54/74FCT863
OET 1
OET
OET 2
10
R
10
T
R
9
9
T
OER 1
OER
OER 2
7.23
2610 drw 03
2
IDT54/74FCT861A/B, IDT54/74FCT863A/B
HIGH-PERFORMANCE CMOS BUS TRANSCEIVERS
MILITARY AND COMMERCIAL TEMPERATURE RANGES
FUNCTION TABLE(1)
PIN DESCRIPTION
Name
I/O
Description
IDT54/74FCT861/863 (Non-inverting)
IDT54/74FCT861
Inputs
OER
I
When LOW in conjunction with OET HIGH
activates the RECEIVE mode.
OET
I
When LOW in conjunction with OER HIGH
activates the TRANSMIT mode.
RI
I/O
10-bit RECEIVE input/output.
TI
I/O
10-bit TRANSMIT input/output.
OET OER
IDT54/74FCT863
OERI
I
When LOW in conjunction with OETI HIGH
activates the RECEIVE mode.
OETI
I
When LOW in conjunction with OERI HIGH
activates the TRANSMIT mode.
RI
I/O
9-bit RECEIVE input/output.
TI
I/O
9-bit TRANSMIT input/output.
Outputs
RI
TI
RI
TI
Function
L
H
L
N/A
N/A
L
Transmitting
L
H
H
N/A
N/A
H
Transmitting
H
L
N/A
L
L
N/A
Receiving
H
L
N/A
H
H
N/A
Receiving
H
H
X
X
Z
Z
High Z
NOTE:
2610 tbl 02
1. H = HIGH, L = LOW, Z = High Impedance, X = Don’t Care, N/A = Not
Applicable.
2610 tbl 01
ABSOLUTE MAXIMUM RATINGS(1)
CAPACITANCE (TA = +25°C, f = 1.0MHz)
Symbol
Rating
VTERM(2) Terminal Voltage
with Respect
to GND
VTERM(3) Terminal Voltage
with Respect
to GND
TA
Operating
Temperature
TBIAS
Temperature
Under Bias
TSTG
Storage
Temperature
PT
Power Dissipation
DC Output Current
IOUT
Symbol
Commercial
Military
Unit
–0.5 to +7.0 –0.5 to +7.0
V
–0.5 to VCC
–0.5 to VCC
V
0 to +70
–55 to +125
°C
–55 to +125
–65 to +135
°C
–55 to +125
–65 to +150
°C
0.5
120
0.5
120
W
mA
Parameter(1)
Conditions Typ.
CIN
Input Capacitance
VIN = 0V
CI/O
I/O Capacitance
VOUT = 0V
Max.
Unit
6
10
pF
8
12
pF
NOTE:
2610 tbl 04
1. This parameter is guaranteed by characterization but not tested.
NOTES:
2610 tbl 03
1. Stresses greater than those listed under ABSOLUTE MAXIMUM
RATINGS may cause permanent damage to the device. This is a stress
rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability. No terminal voltage
may exceed VCC by +0.5V unless otherwise noted.
2. Inputs and VCC terminals only.
3. Outputs and I/O terminals only.
7.23
3
IDT54/74FCT861A/B, IDT54/74FCT863A/B
HIGH-PERFORMANCE CMOS BUS TRANSCEIVERS
MILITARY AND COMMERCIAL TEMPERATURE RANGES
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified: VLC = 0.2V, VHC = VCC – 0.2V
Commercial: TA = 0°C to +70°C, VCC = 5.0V ± 5%; Military: TA = –55°C to +125°C, VCC = 5.0V ± 10%
Symbol
Test Conditions(1)
Min.
Typ.(2)
Max.
Unit
VIH
Input HIGH Level
Guaranteed Logic HIGH Level
2.0
—
—
V
VIL
Input LOW Level
Guaranteed Logic LOW Level
—
—
0.8
V
Input HIGH Current
VCC = Max.
µA
IIH
IIL
IIH
IIL
Parameter
VI = VCC
—
—
5
(Except I/O pins)
VI = 2.7V
—
—
5(4)
Input LOW Current
VI = 0.5V
—
—
–5(4)
(Except I/O pins)
VI = GND
—
—
–5
VI = VCC
—
—
15
(I/O pins Only)
VI = 2.7V
—
—
15(4)
Input LOW Current
VI = 0.5V
—
—
–15(4)
(I/O pins Only)
VI = GND
—
—
–15
Input HIGH Current
VCC = Max.
µA
VIK
Clamp Diode Voltage
VCC = Min., IN = –18mA
—
–0.7
–1.2
V
IOS
Short Circuit Current
VCC = Max.(3), VO = GND
–75
–120
—
mA
VOH
Output HIGH Voltage
VCC = 3V, VIN = VLC or VHC, IOH = –32µA
VHC
VCC
—
V
VCC = Min.
IOH = –300µA
VHC
VCC
—
VIN = VIH or VIL
IOH = –15mA MIL.
2.4
4.3
—
IOH = –24mA COM’L.
VOL
Output LOW Voltage
2.4
4.3
—
VCC = 3V, VIN = VLC or VHC, IOL = 300µA
—
GND
VLC
VCC = Min.
IOL = 300µA
—
GND
VLC(4)
VIN = VIH or VIL
IOL = 32mA MIL.(5)
—
0.3
0.5
IOL = 48mA COM’L.(5)
—
0.3
0.5
V
NOTES:
2610 tbl 05
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the short circuit test should not exceed one second.
4. This parameter is guaranteed but not tested.
5. These are maximum IOL values per output, for 10 outputs turned on simultaneously. Total maximum IOL (all outputs) is 480mA for commercial and 320mA
for military. Derate IOL for number of outputs exceeding 10 turned on simultaneously.
7.23
4
IDT54/74FCT861A/B, IDT54/74FCT863A/B
HIGH-PERFORMANCE CMOS BUS TRANSCEIVERS
MILITARY AND COMMERCIAL TEMPERATURE RANGES
POWER SUPPLY CHARACTERISTICS
VLC = 0.2V; VHC = VCC – 0.2V
Symbol
Parameter
Test Conditions(1)
Min.
Typ.(2)
Max.
Unit
ICC
Quiescent Power
Supply Current
VCC = Max.
VIN ≥ VHC ; VIN ≤ V LC
—
0.2
1.5
mA
∆ICC
Quiescent Power Supply
Current TTL Inputs HIGH
VCC = Max.
VIN = 3.4V(3)
—
0.5
2.0
mA
ICCD
Dynamic Power Supply Current(4)
VCC = Max., Outputs Open
OER or OET = GND
One Input Toggling
50% Duty Cycle
VIN ≥ VHC
VIN ≤ VLC
—
0.15
0.25
mA/
MHz
IC
Total Power Supply Current(6)
VCC = Max., Outputs Open
fi = 10MHz
50% Duty Cycle
VIN ≥ VHC
VIN ≤ VLC
(FCT)
—
1.7
4.0
mA
OER or OET = GND
One Bit Toggling
VIN = 3.4V
VIN = GND
—
2.0
5.0
VCC = Max., Outputs Open
fi = 2.5MHz
50% Duty Cycle
VIN ≥ VHC
VIN ≤ VLC
(FCT)
—
3.2
6.5(5)
OER or OET = GND
VIN = 3.4V
VIN = GND
—
5.2
14.5(5)
Eight Bits Toggling
NOTES:
1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V); all other inputs at VCC or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply calculations.
5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested.
6. IC = IQUIESCENT +IINPUTS + IDYNAMIC
IC = ICC + ∆ICCDHNT + ICCD(fCP/2 + fiNi)
ICC = Quiescent Current
∆ICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL)
fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices)
fi = Input Frequency
Ni = Number of Inputs at fi
All currents are in milliamps and all frequencies are in megahertz.
7.23
2610 tbl 06
5
IDT54/74FCT861A/B, IDT54/74FCT863A/B
HIGH-PERFORMANCE CMOS BUS TRANSCEIVERS
MILITARY AND COMMERCIAL TEMPERATURE RANGES
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
FCT861A/863A
Com'l.
Symbol
tPLH
tPHL
tPZH
tPZL
tPHZ
tPLZ
Parameter
Propagation Delay
RI to TI or TI to RI
FCT861/863
Output Enable Time
OET to TI or OER to RI
Output Disable Time
OET to TI or OER to RI
Condition(1)
CL = 50pF
RL = 500Ω
CL = 300pF(3)
RL = 500Ω
CL = 50pF
RL = 500Ω
CL = 300pF(3)
RL = 500Ω
CL = 5pF(3)
RL = 500Ω
CL = 50pF
RL = 500Ω
FCT861B/863B
Mil.
Com'l.
Mil.
Min.(2)
1.5
Max.
8.0
Min.(2)
1.5
Max.
9.0
Min.(2)
1.5
Max.
6.0
Min. (2)
1.5
Max.
6.5
1.5
15.0
1.5
17.0
1.5
13.0
1.5
14.0
1.5
12.0
1.5
13.0
1.5
8.0
1.5
9.0
1.5
20.0
1.5
22.0
1.5
15.0
1.5
16.0
1.5
9.0
1.5
9.0
1.5
6.0
1.5
7.0
1.5
10.0
1.5
10.0
1.5
7.0
1.5
8.0
NOTES:
1. See test circuits and waveforms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
3. This condition guaranteed but not tested.
Unit
ns
ns
ns
2610 tbl 07
7.23
6
IDT54/74FCT861A/B, IDT54/74FCT863A/B
HIGH-PERFORMANCE CMOS BUS TRANSCEIVERS
MILITARY AND COMMERCIAL TEMPERATURE RANGES
TEST CIRCUITS AND WAVEFORMS
TEST CIRCUITS FOR ALL OUTPUTS
SWITCH POSITION
V CC
7.0V
500Ω
VOUT
VIN
Pulse
Generator
D.U.T.
50pF
RT
SET-UP, HOLD AND RELEASE TIMES
TIMING
INPUT
ASYNCHRONOUS CONTROL
PRESET
CLEAR
ETC.
SYNCHRONOUS CONTROL
PRESET
CLEAR
CLOCK ENABLE
ETC.
tH
tSU
tREM
tSU
Switch
Open Drain
Disable Low
Enable Low
Closed
All Other Tests
Open
DEFINITIONS:
2610 tbl 08
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse
Generator.
500Ω
CL
DATA
INPUT
Test
PULSE WIDTH
3V
1.5V
0V
3V
1.5V
0V
LOW-HIGH-LOW
PULSE
1.5V
tW
3V
1.5V
0V
HIGH-LOW-HIGH
PULSE
1.5V
3V
1.5V
0V
tH
PROPAGATION DELAY
ENABLE AND DISABLE TIMES
ENABLE
SAME PHASE
INPUT TRANSITION
tPLH
tPHL
OUTPUT
tPLH
OPPOSITE PHASE
INPUT TRANSITION
tPHL
3V
1.5V
0V
VOH
1.5V
VOL
DISABLE
3V
1.5V
0V
CONTROL
INPUT
tPLZ
tPZL
OUTPUT
NORMALLY
LOW
3V
1.5V
0V
SWITCH
CLOSED
3.5V
1.5V
tPZH
OUTPUT
NORMALLY
HIGH
SWITCH
OPEN
3.5V
0.3V
VOL
tPHZ
0.3V
1.5V
0V
VOH
0V
2610 drw 03
NOTES:
1. Diagram shown for input Control Enable-LOW and input Control DisableHIGH
2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns
7.23
7
IDT54/74FCT861A/B, IDT54/74FCT863A/B
HIGH-PERFORMANCE CMOS BUS TRANSCEIVERS
MILITARY AND COMMERCIAL TEMPERATURE RANGES
ORDERING INFORMATION
IDT
XX
Temperature
Range
FCT XXXX
Device
Type
X
X
Package
Process
7.23
Blank
B
Commercial
MIL-STD-883, Class B
P
D
E
L
SO
Plastic DIP
CERDIP
CERPACK
Leadless Chip Carrier
Small Outline IC
861A
863A
861B
863B
10-Bit Non-inverting Transceiver
9-Bit Non-inverting Transceiver
54
74
-55°C to +125°C
0° to +70°C
2610 drw 04
8
Similar pages