MAPDCC0004
Low Cost Two-Way SMT Power
Divider, 1700 - 1900 MHz
Features
Small Size and Low Profile
Industry Standard SOIC-8 SMT Plastic Package
Superior Repeatability
Excellent Amplitude Balance: 0.05 dB Typical
Excellent Insertion Loss: 0.3 dB Typical
Low Cost
DCS-1800 Frequency Coverage
Lead-Free SOIC-8 Package
100% Matte Tin Plating over Copper
Halogen-Free “Green” Mold Compound
260°C Reflow Compatible
RoHS* Compliant Version of DS52-0005
Rev. V3
Functional Block Diagram
Description
M/A-COM’s MAPDCC0004 is an IC-based
monolithic power divider in a low cost SOIC-8 plastic
package. This 2-way power splitter is ideally suited
for applications where small size, low profile and low
cost, without sacrificing performance are required.
Typical applications include base station, portables
and PCMCIA cards for DCS-1800 European applications. Available in tape and reel.
The MAPDCC0004 is fabricated using a passiveintegrated circuit process. The process features fullchip passivation for increased performance and
reliability.
Pin Configuration
Ordering Information
Function
1
GND
2
RF-IN
Part Number
Package
MAPDCC0004
Bulk Packaging
3
GND
MAPDCC0004TR
1000 piece reel
4
GND
MAPDCC0004-TB
Sample Test Board
5
RF-1 (out)
6
GND
7
GND
8
RF-2 (out)
Note: Reference Application Note M513 for reel size
information.
1
Pin No.
* Restrictions on Hazardous Substances, European Union Directive 2002/95/EC.
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0004
Low Cost Two-Way SMT Power
Divider, 1700 - 1900 MHz
Rev. V3
Electrical Specifications1: TA = 25°C
1.
Parameter
Test Conditions
Frequency
Units
Min
Typ
Max
Insertion Loss
Above 3.0 dB
1700 - 1900
dB
—
0.3
0.5
Isolation
—
1700 - 1900
dB
15
20
—
VSWR
—
1700 - 1900
Ratio
—
1.3:1
1.5:1
Amplitude Balance
—
1700 - 1900
dB
—
0.1
0.15
Phase Balance
—
1700 - 1900
Deg
—
2
4
All specifications apply with a 50-ohm source and load impedance.
Absolute Maximum Ratings 2,3
Parameter
Input Power
2.
3.
4.
Absolute Maximum
4
Recommended PCB Configuration
1W CW
Operating Temperature
-40°C to +85°C
Storage Temperature
-65°C to +150°C
Exceeding any one or combination of these limits may cause
permanent damage to this device.
M/A-COM does not recommend sustained operation near
these survivability limits.
With internal load dissipation of 0.125W maximum
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
GMIC Circuits are sensitive to electrostatic
discharge (ESD) and can be damaged by static
electricity. Proper ESD control techniques should
be used when handling these devices.
2
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0004
Low Cost Two-Way SMT Power
Divider, 1700 - 1900 MHz
Rev. V3
Typical Performance Curves
Isolation vs. Frequency
0.5
30
0.4
25
Isolation (dB)
Insertion Loss (dB)
Insertion Loss vs. Frequency
(above theoretical split loss)
0.3
0.2
0.1
0.0
1700
20
15
10
5
0
1740
1780
1820
1860
1700
1900
1740
Frequency (MHz)
1860
1900
1860
1900
Output VSWR vs. Frequency
1.5
1.5
1.4
1.4
1.3
1.3
VSWR
VSWR
1820
F requency (M H z)
Input VSWR vs. Frequency
1.2
1.2
1.1
1.1
1.0
1700
1780
1740
1780
1820
Frequency (MHz)
1860
1900
1.0
1700
1740
1780
1820
Frequency (MHz)
3
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0004
Low Cost Two-Way SMT Power
Divider, 1700 - 1900 MHz
Rev. V3
Lead-Free, SOIC-8†
†
Reference Application Note M538 for lead-free solder reflow
recommendations.
4
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support
MAPDCC0004
Low Cost Two-Way SMT Power
Divider, 1700 - 1900 MHz
Rev. V3
M/A-COM Technology Solutions Inc. All rights reserved.
Information in this document is provided in connection with M/A-COM Technology Solutions Inc ("MACOM")
products. These materials are provided by MACOM as a service to its customers and may be used for
informational purposes only. Except as provided in MACOM's Terms and Conditions of Sale for such products or
in any separate agreement related to this document, MACOM assumes no liability whatsoever. MACOM
assumes no responsibility for errors or omissions in these materials. MACOM may make changes to
specifications and product descriptions at any time, without notice. MACOM makes no commitment to update
the information and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future
changes to its specifications and product descriptions. No license, express or implied, by estoppels or otherwise,
to any intellectual property rights is granted by this document.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, RELATING TO SALE AND/OR USE OF MACOM PRODUCTS INCLUDING LIABILITY OR
WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, CONSEQUENTIAL OR
INCIDENTAL DAMAGES, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR
OTHER INTELLECTUAL PROPERTY RIGHT. MACOM FURTHER DOES NOT WARRANT THE ACCURACY
OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN
THESE MATERIALS. MACOM SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS,
WHICH MAY RESULT FROM THE USE OF THESE MATERIALS.
MACOM products are not intended for use in medical, lifesaving or life sustaining applications. MACOM
customers using or selling MACOM products for use in such applications do so at their own risk and agree to
fully indemnify MACOM for any damages resulting from such improper use or sale.
5
M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice.
Visit www.macom.com for additional data sheets and product information.
For further information and support please visit:
https://www.macom.com/support