ON CAT5269YI-50-T2 Dual digital potentiometer (pot) Datasheet

CAT5269
Dual Digital
Potentiometer (POT)
with 256 Taps
and 2‐wire Interface
http://onsemi.com
Description
The CAT5269 is two digital POTs integrated with control logic and
18 bytes of NVRAM memory. Each digital POT consists of a series of
resistive elements connected between two externally accessible end
points. The tap points between each resistive element are connected to
the wiper outputs with CMOS switches. A separate 8-bit control
register (WCR) independently controls the wiper tap switches for each
digital POT. Associated with each wiper control register are four 8-bit
non-volatile memory data registers (DR) used for storing up to four
wiper settings. Writing to the wiper control register or any of the
non-volatile data registers is via a 2-wire serial bus. On power-up, the
contents of the first data register (DR0) for each of the potentiometers
is automatically loaded into its respective wiper control registers.
The CAT5269 can be used as a potentiometer or as a two terminal,
variable resistor. It is intended for circuit level or system level
adjustments in a wide variety of applications. It is available in the
−40C to 85C industrial operating temperature range and offered in a
24-lead SOIC and TSSOP package.
Features














Four Linear Taper Digital Potentiometers
256 Resistor Taps per Potentiometer
End to End Resistance 50 kW or 100 kW
Potentiometer Control and Memory Access via 2-wire Interface
(I2C like)
Low Wiper Resistance, Typically 100 W
Nonvolatile Memory Storage for up to Four Wiper Settings for Each
Potentiometer
Automatic Recall of Saved Wiper Settings at Power Up
2.5 to 6.0 Volt Operation
Standby Current less than 1 mA
1,000,000 Nonvolatile WRITE Cycles
100 Year Nonvolatile Memory Data Retention
24-lead SOIC and TSSOP Packages
Industrial Temperature Range
These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS
Compliant
 Semiconductor Components Industries, LLC, 2013
July, 2013 − Rev. 7
1
TSSOP−24
Y SUFFIX
CASE 948AR
SOIC−24
W SUFFIX
CASE 751BK
PIN CONNECTIONS
NC
A3
1
A0
SCL
NC
NC
NC
NC
NC
NC
NC
VCC
CAT5269
NC
GND
RL0
RW1
RH0
RH1
RW0
RL1
A1
A2
SDA
WP
SOIC−24 (W)
TSSOP−24 (Y)
(Top View)
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
Publication Order Number:
CAT5269/D
CAT5269
MARKING DIAGRAMS
(SOIC−24)
(TSSOP−24)
L3B
CAT5269WT
−RRYMXXXX
RLB
CAT5269YT
3YMXXX
R = Resistance
1 = 2.5 KW
2 = 10 KW
4 = 50 KW
5 = 100 KW
L = Assembly Location
B = Product Revision (Fixed as “B”)
CAT5269Y = Device Code
T = Temperature Range (I = Industrial)
3 = Lead Finish − Matte-Tin
Y = Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
XXX = Last Three Digits of Assembly Lot Number
L = Assembly Location
3 = Lead Finish − Matte-Tin
B = Product Revision (Fixed as “B”)
CAT5269W = Device Code
T = Temperature Range (I = Industrial)
− = Dash
RR = Resistance
25 = 2.5 KW
10 = 10 KW
50 = 50 KW
00 = 100 KW
Y = Production Year (Last Digit)
M = Production Month (1−9, O, N, D)
XXXX = Last Four Digits of Assembly Lot Number
RH0
SCL
SDA
RH1
WIPER
CONTROL
REGISTERS
2−WIRE BUS
INTERFACE
RW0
RW1
WP
A0
A1
A2
A3
NONVOLATILE
DATA
REGISTERS
CONTROL
LOGIC
RL0
Figure 1. Functional Diagram
http://onsemi.com
2
RL1
CAT5269
PIN DESCRIPTIONS
SCL: Serial Clock
The CAT5269 serial clock input pin is used to clock all data
transfers into or out of the device.
SDA: Serial Data
The CAT5269 bidirectional serial data pin is used to transfer
data into and out of the device. The SDA pin is an open drain
output and can be wire-Ored with the other open drain or
open collector I/Os.
A0, A1, A2, A3: Device Address Inputs
These inputs set the device address when addressing
multiple devices. A total of sixteen devices can be addressed
on a single bus. A match in the slave address must be made
with the address input in order to initiate communication
with the CAT5269.
RH, RL: Resistor End Points
The two sets of RH and RL pins are equivalent to the terminal
connections on a mechanical potentiometer.
RW: Wiper
The RW pins are equivalent to the wiper terminal of a
mechanical potentiometer.
WP: Write Protect Input
The WP pin when tied low prevents non-volatile writes to
the data register (change of wiper control register is allowed)
and when tied high or left floating normal read/write
operations are allowed. See Write Protection on page 8 for
more details.
Table 1. PIN DESCRIPTIONS
Pin #
Name
Function
1
NC
No Connect
2
A0
Device Address, LSB
3
NC
No Connect
4
NC
No Connect
5
NC
No Connect
6
NC
No Connect
7
VCC
Supply Voltage
8
RL0
Low Reference Terminal for
Potentiometer 0
9
RH0
High Reference Terminal for
Potentiometer 0
10
RW0
Wiper Terminal for Potentiometer 0
11
A2
Device Address
12
WP
Write Protection
13
SDA
Serial Data Input/Output
14
A1
Device Address
15
RL1
Low Reference Terminal for
Potentiometer 1
16
RH1
High Reference Terminal for
Potentiometer 1
17
RW1
Wiper Terminal for Potentiometer 1
18
GND
Ground
19
NC
No Connect
20
NC
No Connect
21
NC
No Connect
22
NC
No Connect
23
SCL
Bus Serial Clock
24
A3
Device Address
DEVICE OPERATION
The CAT5269 is two resistor arrays integrated with a
2-wire serial interface, two 8-bit wiper control registers and
eight 8-bit, non-volatile memory data registers. Each
resistor array contains 255 separate resistive elements
connected in series. The physical ends of each array are
equivalent to the fixed terminals of a mechanical
potentiometer (RH and RL). The tap positions between and
at the ends of the series resistors are connected to the output
wiper terminals (RW) by a CMOS transistor switch. Only
one tap point for each potentiometer is connected to its wiper
terminal at a time and is determined by the value of the wiper
control register. Data can be read or written to the wiper
control registers or the non-volatile memory data registers
via the 2-wire bus. Additional instructions allow data to be
transferred between the wiper control registers and each
respective potentiometer’s non-volatile data registers. Also,
the device can be instructed to operate in an “increment/
decrement” mode.
http://onsemi.com
3
CAT5269
Table 2. ABSOLUTE MAXIMUM RATINGS
Parameters
Ratings
Units
Temperature Under Bias
−55 to +125
C
Storage Temperature
−65 to +150
C
−2.0 to +VCC + 2.0
V
Voltage on Any Pin with Respect to VSS (Note 1)
VCC with Respect to Ground
−2.0 to +7.0
V
Package Power Dissipation Capability (TA = 25C)
1.0
W
Lead Soldering Temperature (10 s)
300
C
Wiper Current
6
mA
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 3. RECOMMENDED OPERATING CONDITIONS
Parameters
Ratings
Units
VCC
+2.5 to +6.0
V
Industrial Temperature
−40 to +85
C
Table 4. POTENTIOMETER CHARACTERISTICS (Over recommended operating conditions unless otherwise stated.)
Limits
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
RPOT
Potentiometer Resistance (100 kW)
100
kW
RPOT
Potentiometer Resistance (50 kW)
50
kW
Potentiometer Resistance Tolerance
RPOT Matching
Power Rating
25C, each pot
20
%
1
%
50
mW
3
mA
IW
Wiper Current
RW
Wiper Resistance
IW = 3 mA @ VCC = 3 V
200
300
W
RW
Wiper Resistance
IW = 3 mA @ VCC = 5 V
100
150
W
VTERM
Voltage on any RH or RL Pin
VSS = 0 V
Resolution
VSS
VCC
0.4
V
%
Absolute Linearity (Note 4)
Rw(n)(actual)−R(n)(expected)
(Note 7)
1
LSB
(Note 6)
Relative Linearity (Note 5)
Rw(n+1)−[Rw(n)+LSB]
(Note 7)
0.2
LSB
(Note 6)
TCRPOT
Temperature Coefficient of RPOT
(Note 3)
TCRATIO
Ratiometric Temp. Coefficient
(Note 3)
CH/CL/CW
Potentiometer Capacitances
(Note 3)
10/10/25
pF
RPOT = 50 kW (Note 3)
0.4
MHz
fc
Frequency Response
ppm/C
300
20
ppm/C
1. The minimum DC input voltage is –0.5 V. During transitions, inputs may undershoot to –2.0 V for periods of less than 20 ns. Maximum DC
voltage on output pins is VCC +0.5 V, which may overshoot to VCC +2.0 V for periods of less than 20 ns.
2. Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1 V to VCC +1 V.
3. This parameter is tested initially and after a design or process change that affects the parameter.
4. Absolute linearity is utilized to determine actual wiper voltage versus expected voltage as determined by wiper position when used as a
potentiometer.
5. Relative linearity is utilized to determine the actual change in voltage between two successive tap positions when used as a potentiometer.
It is a measure of the error in step size.
6. LSB = RTOT / 255 or (RH − RL) / 255, single pot
7. n = 0, 1, 2, ..., 255
http://onsemi.com
4
CAT5269
Table 5. D.C. OPERATING CHARACTERISTICS (VCC = +2.5 V to +6.0 V, unless otherwise specified.)
Symbol
Parameter
Test Conditions
Min
Max
Units
ICC1
Power Supply Current
fSCL = 400 kHz, SDA = Open
VCC = 6 V, Inputs = GND
1
mA
ICC2
Power Supply Current
Non-volatile WRITE
fSCK = 400 kHz, SDA Open
VCC = 6 V, Input = GND
5
mA
ISB
Standby Current (VCC = 5 V)
VIN = GND or VCC, SDA = Open
5
mA
ILI
Input Leakage Current
VIN = GND to VCC
10
mA
ILO
Output Leakage Current
VOUT = GND to VCC
10
mA
VIL
Input Low Voltage
−1
VCC x 0.3
V
VIH
Input High Voltage
VCC x 0.7
VCC + 1.0
V
0.4
V
VOL1
Output Low Voltage (VCC = 3 V)
IOL = 3 mA
Table 6. CAPACITANCE (TA = 25C, f = 1.0 MHz, VCC = 5 V)
Symbol
Conditions
Max
Units
CI/O (Note 8)
Input/Output Capacitance (SDA)
Test
VI/O = 0 V
8
pF
CIN (Note 8)
Input Capacitance (A0, A1, A2, A3, SCL, WP)
VIN = 0 V
6
pF
Table 7. A.C. CHARACTERISTICS
2.5 V − 6.0 V
Max
Units
Clock Frequency
400
kHz
Noise Suppression Time Constant at SCL, SDA Inputs
200
ns
1
ms
Symbol
fSCL
TI (Note 8)
tAA
tBUF (Note 8)
Min
Parameter
SLC Low to SDA Data Out and ACK Out
Time the bus must be free before a new transmission can start
1.2
ms
Start Condition Hold Time
0.6
ms
tLOW
Clock Low Period
1.2
ms
tHIGH
Clock High Period
0.6
ms
tHD:STA
tSU:STA
Start Condition Setup Time (for a Repeated Start Condition)
0.6
ms
tHD:DAT
Data in Hold Time
0
ns
tSU:DAT
Data in Setup Time
50
ns
tR (Note 8)
SDA and SCL Rise Time
0.3
ms
tF (Note 8)
SDA and SCL Fall Time
300
ns
tSU:STO
tDH
Stop Condition Setup Time
0.6
ms
Data Out Hold Time
100
ns
8. This parameter is tested initially and after a design or process change that affects the parameter.
http://onsemi.com
5
CAT5269
Table 8. POWER UP TIMING (Notes 9, 10)
Parameter
Symbol
Max
Units
tPUR
Power-up to Read Operation
1
ms
tPUW
Power-up to Write Operation
1
ms
Max
Units
Wiper Response Time After Power Supply Stable
10
ms
Wiper Response Time After Instruction Issued
10
ms
Max
Units
5
ms
Table 9. WIPER TIMING
Symbol
tWRPO
tWRL
Parameter
Table 10. WRITE CYCLE LIMITS (Note 11)
Symbol
tWR
Parameter
Write Cycle Time
Table 11. RELIABILITY CHARACTERISTICS
Symbol
NEND (Note 9)
Parameter
Reference Test Method
Min
Max
Units
Endurance
MIL−STD−883, Test Method 1033
1,000,000
Cycles/Byte
TDR (Note 9)
Data Retention
MIL−STD−883, Test Method 1008
100
Years
VZAP (Note 9)
ESD Susceptibility
MIL−STD−883, Test Method 3015
2000
V
ILTH (Note 9)
Latch-up
JEDEC Standard 17
100
mA
9. This parameter is tested initially and after a design or process change that affects the parameter.
10. tPUR and tPUW are delays required from the time VCC is stable until the specified operation can be initiated.
11. The write cycle is the time from a valid stop condition of a write sequence to the end of the internal program/erase cycle. During the write
cycle, the bus interface circuits are disabled, SDA is allowed to remain high, and the device does not respond to its slave address.
tF
tHIGH
tR
tLOW
tLOW
SCL
tSU:STA
tHD:STA
tHD:DAT
tSU:DAT
tSU:STO
SDA IN
tAA
tDH
SDA OUT
Figure 2. Bus Timing
http://onsemi.com
6
tBUF
CAT5269
SERIAL BUS PROTOCOL
The following defines the features of the 2-wire bus
protocol:
1. Data transfer may be initiated only when the bus is
not busy.
2. During a data transfer, the data line must remain
stable whenever the clock line is high. Any
changes in the data line while the clock is high
will be interpreted as a START or STOP condition.
Therefore, the CAT5269 will be considered a slave device
in all applications.
The device controlling the transfer is a master, typically a
processor or controller, and the device being controlled is the
slave. The master will always initiate data transfers and
provide the clock for both transmit and receive operations.
STOP Condition
START Condition
The START Condition precedes all commands to the
device, and is defined as a HIGH to LOW transition of SDA
when SCL is HIGH. The CAT5269 monitors the SDA and
SCL lines and will not respond until this condition is met.
A LOW to HIGH transition of SDA when SCL is HIGH
determines the STOP condition. All operations must end
with a STOP condition.
DEVICE ADDRESSING
Acknowledge
The bus Master begins a transmission by sending a
START condition. The Master then sends the address of the
particular slave device it is requesting. The four most
significant bits of the 8-bit slave address are fixed as 0101
for the CAT5269 (see Figure 6). The next four significant
bits (A3, A2, A1, A0) are the device address bits and define
which device the Master is accessing. Up to sixteen devices
may be individually addressed by the system. Typically,
+5 V and ground are hard-wired to these pins to establish the
device’s address.
After the Master sends a START condition and the slave
address byte, the CAT5269 monitors the bus and responds
with an acknowledge (on the SDA line) when its address
matches the transmitted slave address.
After a successful data transfer, each receiving device is
required to generate an acknowledge. The Acknowledging
device pulls down the SDA line during the ninth clock cycle,
signaling that it received the 8 bits of data.
The CAT5269 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation, it
responds with an acknowledge after receiving each 8−bit
byte.
When the CAT5269 is in a READ mode it transmits 8 bits
of data, releases the SDA line, and monitors the line for an
acknowledge. Once it receives this acknowledge, the
CAT5269 will continue to transmit data. If no acknowledge
is sent by the Master, the device terminates data transmission
and waits for a STOP condition.
WRITE OPERATIONS
Acknowledge Polling
In the Write mode, the Master device sends the START
condition and the slave address information to the Slave
device. After the Slave generates an acknowledge, the
Master sends the instruction byte that defines the requested
operation of CAT5269. The instruction byte consist of a
four-bit opcode followed by two register selection bits and
two pot selection bits. After receiving another acknowledge
from the Slave, the Master device transmits the data to be
written into the selected register. The CAT5269
acknowledges once more and the Master generates the
STOP condition, at which time if a nonvolatile data register
is being selected, the device begins an internal programming
cycle to non-volatile memory. While this internal cycle is in
progress, the device will not respond to any request from the
Master device.
The disabling of the inputs can be used to take advantage
of the typical write cycle time. Once the stop condition is
issued to indicate the end of the host’s write operation, the
CAT5269 initiates the internal write cycle. ACK polling can
be initiated immediately. This involves issuing the start
condition followed by the slave address. If the CAT5269 is
still busy with the write operation, no ACK will be returned.
If the CAT5269 has completed the write operation, an ACK
will be returned and the host can then proceed with the next
instruction operation.
http://onsemi.com
7
CAT5269
WRITE PROTECTION
The Write Protection feature allows the user to protect
against inadvertent programming of the non-volatile data
registers. If the WP pin is tied to LOW, the data registers are
protected and become read only. Similarly, the WP pin going
low after start will interrupt a nonvolatile write to data
registers, while the WP pin going low after an internal write
cycle has stated will have no effect on any write operation
(see also CAT5409 or CAT5259). The CAT5269 will accept
both slave addresses and instructions, but the data registers
are protected from programming by the device’s failure to
send an acknowledge after data is received.
SCL
SDA
8TH BIT
ACK
BYTE n
tWR
STOP
CONDITION
START
CONDITION
Figure 3. Write Cycle Timing
SDA
SCL
START CONDITION
STOP CONDITION
Figure 4. Start/Stop Condition
SCL FROM
MASTER
1
8
9
DATA OUTPUT
FROM TRANSMITTER
DATA OUTPUT
FROM RECEIVER
ACKNOWLEDGE
START
Figure 5. Acknowledge Condition
CAT5269
0
1
0
1
A3
A2
Figure 6. Slave Address Bits
* A0, A1, A2 and A3 correspond to pin A0, A1, A2 and A3 of the device.
** A0, A1, A2 and A3 must compare to its corresponding hard wired input pins.
http://onsemi.com
8
A1
A0
ADDRESS
CAT5269
INSTRUCTION AND REGISTER DESCRIPTION
Slave Address Byte
Instruction Byte
The first byte sent to the CAT5269 from the
master/processor is called the Slave Address Byte. The most
significant four bits of the slave address are a device type
identifier. These bits for the CAT5269 are fixed at 0101[B]
(refer to Figure 8).
The next four bits, A3 − A0, are the internal slave address
and must match the physical device address which is defined
by the state of the A3 − A0 input pins for the CAT5269 to
successfully continue the command sequence. Only the
device which slave address matches the incoming device
address sent by the master executes the instruction. The A3
− A0 inputs can be actively driven by CMOS input signals
or tied to VCC or VSS.
The next byte sent to the CAT5269 contains the
instruction and register pointer information. The four most
significant bits used provide the instruction opcode I3 − I0.
The R1 and R0 bits point to one of the four data registers of
each associated potentiometer. The least two significant bits
point to one of four Wiper Control Registers. The format is
shown in Figure 9.
SDA LINE
Register
Address
Pot1 WCR
Address
op code
Variable
Fixed
Data Register Selected
R1
R0
DR0
0
0
DR1
0
1
INSTRUCTION
BYTE
SLAVE
ADDRESS
S
T
BUS ACTIVITY: A
MASTER R
T
Table 12. DATA REGISTER SELECTION
S
T
DR1 WCRDATA O
P
P
S
A
C
K
A
C
K
A
C
K
Figure 7. Write Timing
Device Type
Identifier
ID3
Slave Address
ID2
ID1
1
0
0
ID0
A3
A2
A1
A0
1
(MSB)
(LSB)
Figure 8. Identification Byte Format
Instruction
Opcode
I3
I2
Data Register
Selection
I1
I0
R1
R0
(MSB)
WCR/Pot Selection
P1
P0
(LSB)
Figure 9. Instruction Byte Format
WIPER CONTROL AND DATA REGISTERS
Wiper Control Register (WCR)
modified one step at a time by the Increment/decrement
instruction (see Instruction section for more details).
Finally, it is loaded with the content of its data register zero
(DR0) upon power-up.
The Wiper Control Register is a volatile register that loses
its contents when the CAT5269 is powered-down. Although
the register is automatically loaded with the value in DR0
upon power-up, this may be different from the value present
at power-down.
The CAT5269 contains two 8-bit Wiper Control
Registers, one for each potentiometer. The Wiper Control
Register output is decoded to select one of 256 switches
along its resistor array. The contents of the WCR can be
altered in four ways: it may be written by the host via Write
Wiper Control Register instruction; it may be written by
transferring the contents of one of four associated Data
Registers via the XFR Data Register instruction; it can be
http://onsemi.com
9
CAT5269
Data Registers (DR)
Instructions
Each potentiometer has four 8-bit non-volatile Data
Registers. These can be read or written directly by the host.
Data can also be transferred between any of the four Data
Registers and the associated Wiper Control Register. Any
data changes in one of the Data Registers is a non-volatile
operation and will take a maximum of 10 ms.
If the application does not require storage of multiple
settings for the potentiometer, the Data Registers can be used
as standard memory locations for system parameters or user
preference data.
Four of the nine instructions are three bytes in length.
These instructions are:
 Read Wiper Control Register – read the current
wiper position of the selected potentiometer in the
WCR
 Write Wiper Control Register – change current
wiper position in the WCR of the selected
potentiometer
 Read Data Register – read the contents of the
selected Data Register
 Write Data Register – write a new value to the
selected Data Register
Table 13. INSTRUCTION SET
Instruction Set
I3
I2
I1
I0
R1
R0
WCR1/
P1
WCR0/
P0
Read Wiper Control
Register
1
0
0
1
0
0
1/0
1/0
Read the contents of the Wiper Control Register
pointed to by P1−P0
Write Wiper Control
Register
1
0
1
0
0
0
1/0
1/0
Write new value to the Wiper Control Register
pointed to by P1−P0
Read Data Register
1
0
1
1
1/0
1/0
1/0
1/0
Read the contents of the Data Register pointed
to by P1−P0 and R1−R0
Write Data Register
1
1
0
0
1/0
1/0
1/0
1/0
Write new value to the Data Register pointed to
by P1−P0 and R1−R0
XFR Data Register to
Wiper Control
Register
1
1
0
1
1/0
1/0
1/0
1/0
Transfer the contents of the Data Register
pointed to by P1−P0 and R1−R0 to its
associated Wiper Control Register
XFR Wiper Control
Register to Data
Register
1
1
1
0
1/0
1/0
1/0
1/0
Transfer the contents of the Wiper Control
Register pointed to by P1−P0 to the Data
Register pointed to by R1−R0
Gang XFR Data
Registers to Wiper
Control Registers
0
0
0
1
1/0
1/0
0
0
Transfer the contents of the Data Registers
pointed to by R1−R0 of both pots to their
respective Wiper Control Registers
Gang XFR Wiper
Control Registers to
Data Register
1
0
0
0
1/0
1/0
0
0
Transfer the contents of both Wiper Control
Registers to their respective data Registers
pointed to by R1−R0 of both pots
Increment/Decrement
Wiper Control Register
0
0
1
0
0
0
1/0
1/0
Enable Increment/decrement of the Control
Latch pointed to by P1−P0
Instruction
NOTE:
Operation
1/0 = data is one or zero
The basic sequence of the three byte instructions is
illustrated in Figure 11. These three-byte instructions
exchange data between the WCR and one of the Data
Registers. The WCR controls the position of the wiper. The
response of the wiper to this action will be delayed by tWR.
A transfer from the WCR (current wiper position), to a Data
Register is a write to non-volatile memory and takes a
minimum of tWR to complete. The transfer can occur
between one of the two potentiometers and one of its
associated registers; or the transfer can occur between both
potentiometers and one associated register.
Four instructions require a two-byte sequence to
complete, as illustrated in Figure 10. These instructions
transfer data between the host/processor and the CAT5269;
either between the host and one of the data registers or
directly between the host and the Wiper Control Register.
http://onsemi.com
10
CAT5269
Increment/Decrement Command
These instructions are:
 XFR Data Register to Wiper Control Register −
This transfers the contents of one specified Data
Register to the associated Wiper Control Register.
 XFR Wiper Control Register to Data Register −
This transfers the contents of the specified Wiper
Control Register to the specified associated Data
Register.
 Gang XFR Data Register to Wiper Control
Register − This transfers the contents of all specified
Data Registers to the associated Wiper Control
Registers.
 Gang XFR Wiper Counter Register to Data
Register − This transfers the contents of all Wiper
Control Registers to the specified associated Data
Registers.
SDA
0
1
0
The final command is Increment/Decrement (Figures 12
and 13). The Increment/Decrement command is different
from the other commands. Once the command is issued and
the CAT5269 has responded with an acknowledge, the
master can clock the selected wiper up and/or down in one
segment steps; thereby providing a fine tuning capability to
the host. For each SCL clock pulse (tHIGH) while SDA is
HIGH, the selected wiper will move one resistor segment
towards the RH terminal. Similarly, for each SCL clock
pulse while SDA is LOW, the selected wiper will move one
resistor segment towards the RL terminal.
See Instructions format for more detail.
1
S ID3 ID2 ID1 ID0 A3 A2 A1 A0
T
A
Internal
Device ID
R
Address
T
A
C
K
I3
I2
A
C
K
Register Pot/WCR
Address Address
I1 I0 R1 R0 P1 P0
Instruction
Opcode
S
T
O
P
Figure 10. Two-byte Instruction Sequence
SDA
0
1
0
1
S ID3 ID2 ID1 ID0 A3 A2 A1 A0 A
T
C
A
K
Internal
Device ID
R
Address
T
I3
I2
I1 I0 R1 R0 P1 P0 A
C
K
Instruction
Data Pot/WCR
Opcode
Register Address
Address
D7 D6 D5 D4 D3 D2 D1 D0
WCR[7:0]
or
Data Register D[7:0]
A S
C T
K O
P
Figure 11. Three-byte Instruction Sequence
0
SDA
S
T
A
R
T
1
0
1
ID3 ID2 ID1 ID0 A3
Device ID
A2 A1 A0
Internal
Address
A
C
K
I3
I2
I1
Instruction
Opcode
I0
R1 R0 P1 P0
A
C
Data Pot/WCR K
Register Address
Address
I
N
C
1
Figure 12. Increment/Decrement Instruction Sequence
INC/DEC
Command
Issued
tWRL
SCL
SDA
RW
Voltage Out
Figure 13. Increment/Decrement Timing Limits
http://onsemi.com
11
I
N
C
2
I
N
C
n
D
E
C
1
D
E
C
n
S
T
O
P
CAT5269
INSTRUCTION FORMAT
Table 14. READ WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
P0
A
C
K
P0
A
C
K
P0
A
C
K
P0
A
C
K
INSTRUCTION
1
0
0
1
0
0
P1
0
A
C
K
S
T
O
P
0
A
C
K
S
T
O
P
0
A
C
K
S
T
O
P
0
A
C
K
S
T
O
P
DATA
7
6
5
4
3
2
1
Table 15. WRITE WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
0
1
0
0
0
P1
DATA
7
6
5
4
3
2
1
Table 16. READ DATA REGISTER (DR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
0
1
1
R1
R0
P1
DATA
7
6
5
4
3
2
1
Table 17. WRITE DATA REGISTER (DR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
1
0
0
R1
R0
P1
DATA
7
6
5
4
3
2
Table 18. GANG TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
A
C
K
S
T
O
P
0
A
C
K
S
T
O
P
P0
A
C
K
S
T
O
P
P0
A
C
K
S
T
O
P
INSTRUCTION
0
0
0
1
R1
R0
0
0
Table 19. GANG TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
0
0
0
R1
R0
0
Table 20. TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
1
1
0
R1
R0
P1
Table 21. TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
1
1
0
1
http://onsemi.com
12
R1
R0
P1
1
CAT5269
Table 22. INCREMENT (I)/DECREMENT (D) WIPER CONTROL REGISTER (WCR)
S
T
A
R
T
DEVICE ADDRESSES
0
NOTE:
1
0
1
A3
A2
A1
A0
A
C
K
INSTRUCTION
0
0
1
0
0
0
P1
P0
A
C
K
DATA
I/D
I/D
...
I/D
I/D
S
T
O
P
Any write or transfer to the Non-volatile Data Registers is followed by a high voltage cycle after a STOP has been issued.
Table 23. ORDERING INFORMATION
Orderable Part Number
Resistance (kW)
CAT5269WI−50−T1
50
CAT5269WI−00−T1
100
CAT5269YI−50−T2
50
CAT5269YI−00−T2
100
CAT5269WI50
50
CAT5269WI00
100
CAT5269YI50
50
CAT5269YI00
100
Lead Finish
Package
Shipping†
SOIC
(Pb-Free)
1000 / Tape & Reel
TSSOP
(Pb-Free)
2000 / Tape & Reel
SOIC
(Pb-Free)
31 Units / Tube
TSSOP
(Pb-Free)
62 Units / Tube
Matte-Tin
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
12. For detailed information and a breakdown of device nomenclature and numbering systems, please see the ON Semiconductor Device
Nomenclature document, TND310/D, available at www.onsemi.com.
13. All packages are RoHS-compliant (Pb-Free, Halogen-Free).
14. The standard lead finish is Matte-Tin.
http://onsemi.com
13
CAT5269
PACKAGE DIMENSIONS
SOIC−24, 300 mils
CASE 751BK
ISSUE O
E1
SYMBOL
MIN
A
2.35
2.65
A1
0.10
0.30
A2
2.05
2.55
b
0.31
0.51
c
0.20
0.33
D
15.20
15.40
E
10.11
10.51
E1
7.34
7.60
E
e
PIN#1 IDENTIFICATION
MAX
1.27 BSC
e
b
NOM
h
0.25
0.75
L
0.40
1.27
θ
0º
8º
θ1
5º
15º
TOP VIEW
h
D
A2
A
A1
SIDE VIEW
h
q1
q
q1
L
END VIEW
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MS-013.
http://onsemi.com
14
c
CAT5269
PACKAGE DIMENSIONS
TSSOP24, 4.4x7.8
CASE 948AR
ISSUE A
b
SYMBOL
MIN
NOM
A
E1 E
MAX
1.20
A1
0.05
0.15
A2
0.80
1.05
b
0.19
0.30
c
0.09
0.20
D
7.70
7.80
7.90
E
6.25
6.40
6.55
E1
4.30
4.40
4.50
e
L
0.65 BSC
0.50
L1
θ
0.60
0.70
1.00 REF
0º
8º
e
TOP VIEW
D
c
A2
A θ1
L
A1
SIDE VIEW
END VIEW
L1
Notes:
(1) All dimensions are in millimeters. Angles in degrees.
(2) Complies with JEDEC MO-153.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
15
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
CAT5269/D
Similar pages