NTE Series www.murata-ps.com Isolated 1W Single Output SM DC/DC Converters SELECTION GUIDE 1 Order Code FEATURES RoHS compliant Lead frame technology Single isolated output 1kVDC Isolation Efficiency up to 78% Power density 1.8W/cm3 Wide temperature performance at full 1 Watt load, –40°C to 85°C Nominal Input Voltage V NTE0303MC NTE0305MC NTE0309MC NTE0312MC NTE0315MC NTE0503MC NTE0505MC NTE0505MEC NTE0506MC NTE0509MC NTE0512MC NTE0515MC NTE1205MC NTE1209MC NTE1212MC NTE1215MC V mA Input Current at Rated Load mA 3.3 5 9 12 15 3.3 5 5 6 9 12 15 5 9 12 15 303 200 111 83 66 303 200 200 167 111 83 66 200 111 83 66 410 390 400 400 400 270 294 260 278 267 260 256 124 114 113 111 Output Voltage 3.3 3.3 3.3 3.3 3.3 5 5 5 5 5 5 5 12 12 12 12 Output Current Efficiency Isolation Capacitance % pF kHrs 73 78 77 77 77 74 68 77 72 75 77 78 67 73 74 75 30 35 31 28 29 40 35 40 39 43 42 44 47 77 88 95 5348 3847 3134 3473 2473 5515 6857 3933 6677 5501 3957 2747 4683 4008 3121 2316 MTTF2 UL 94V-0 Package material Footprint over pins 1.37cm2 INPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. 3.3V, 5V, 9V, 12V & 15V output Voltage range No heatsink required Continuous operation, 3.3V input types Continuous operation, 5V input types Continuous operation, 12V input types 2.97 4.5 10.8 Reflected ripple current 3.3 5.0 12.0 30 3.63 5.5 13.2 47 mA p-p Typ. Max. Units 3.3V, 5V & 12V Input Units V Internal SMD construction Toroidal magnetics ISOLATION CHARACTERISTICS Parameter Conditions Min. MTTF up to 6.8 million hours Isolation voltage Resistance Flash tested for 1 second Viso= 1000VDC 1000 10 Custom solutions available Multi-layer ceramic capacitors PRODUCT OVERVIEW The NTE series of miniature surface mounted DC/DC Converters employ leadframe technology and transfer moulding techniques to bring all of the benefits of IC style packaging to hybrid circuitry. The co-planarity of the pin positions is based upon IEC 191-6:1990. The devices are suitable for all applications where high volume production is envisaged. VDC GΩ GENERAL CHARACTERISTICS Parameter Conditions Switching frequency All output types Min. Typ. 110 Max. Units kHz ABSOLUTE MAXIMUM RATINGS Lead temperature 1.5mm from case for 10 seconds Internal power dissipation Input voltage VIN, NTE03 types Input voltage VIN, NTE05 types Input voltage VIN, NTE12 types 300°C 600mW 5.5V 7V 15V 1. If components are required in tape and reel format suffix order code with -R, e.g. NTE0505MC-R. 2. Calculated using MIL-HDBK-217 FN2 calculation model with nominal input voltage at full load. All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified. For full details go to www.murata-ps.com/rohs www.murata-ps.com/support KDC_NTE.K03 Page 1 of 6 NTE Series Isolated 1W Single Output SM DC/DC Converters OUTPUT CHARACTERISTICS Parameter Conditions Rated power Voltage set point accuracy Line regulation TA=-40°C to 85°C See tolerance envelope High VIN to low VIN 10% load to rated load, 03XXMC, 0503MC, 0505MEC 10% load to rated load, 0505MC & 1205MC 10% load to rated load, 0506MC 10% load to rated load, 0509MC & 1209MC 10% load to rated load, 0512MC & 1212MC 10% load to rated load, 0515MC & 1215MC BW=DC to 20MHz, 03XXMC, 0503MC, 0505MEC BW=DC to 20MHz, 0505MC & 1205MC BW=DC to 20MHz, 0506MC BW=DC to 20MHz, 0509MC & 1209MC BW=DC to 20MHz, 0512MC & 1212MC BW=DC to 20MHz, 0515MC & 1215MC Load regulation1 Ripple and noise Min. Typ. Max. Units 1.0 W 1.0 10 12.8 9.2 8.3 6.8 6.3 40 62 103 49 39 38 1.2 14 15 10 9.0 7.5 7.0 60 85 170 75 65 76 %/% Typ. Max. % mV p-p TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Specification Storage All output types -40 -55 Case temperature rise above ambient Cooling 0305MC, 0309MC, 0315MC 0303MC, 0312MC, 0503MC, 0505MEC, 0509MC, 0512MC, 0515MC 0505MC, 1205MC 1209MC, 1212MC, 1215MC Free air convection Units 85 125 25 30 43 40 °C TECHNICAL NOTES ISOLATION VOLTAGE ‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Murata Power Solutions NTE series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second. A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?” For a part holding no specific agency approvals, such as the NTE series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to safety standard requirements. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment. The NTE series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This consideration equally applies to agency recognized parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation system of physical spacing or barriers. TEMPERATURE DERATING GRAPH Output Power (W) 1.5 1.0 0.5 0 -40 85°C Safe Operating Area 100 50 0 Ambient Temperature (°C) 150 1. 12V input types have typically 3% less load regulation change. www.murata-ps.com/support KDC_NTE.K03 Page 2 of 6 NTE Series Isolated 1W Single Output SM DC/DC Converters TOLERANCE ENVELOPES 3.3V output types. All other types. +10% +9% oad Lin Output Voltage +1% VNOM e +1% -7% -7% -15% 10 75 50 25 Output Load Current (%) +5% VNOM 100 Output Voltage Typical L Typical L oad Line +2.5% -2.5% -7.5% 10 75 50 25 Output Load Current (%) 100 The voltage tolerance envelope shows typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to changes in output loading. RoHS COMPLIANCE, MSL AND PSL INFORMATION This series is compatible with RoHS soldering systems and is also backward compatible with Sn/Pb soldering systems. The NTE series has a process, moisture, and reflow sensitivity classification of MSL1 PSL R7F as defined in J-STD-020 and J-STD-075. This translates to: MSL1 = unlimited floor life, PSL R7F = Peak reflow temperature 245°C with a limitation on the time above liquidus (217°C) which for this series is 60sec max. The pin termination finish on this product series is Gold with a plating thickness of 0.05 microns minimum. For further information please visit www.murata-ps.com/rohs APPLICATION NOTES Minimum load The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in an increase in output voltage, which may rise to typically double the specified output voltage if the output load falls to less than 5%. Capacitive loading and start up Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF. NTE0303MC NTE0305MC NTE0309MC NTE0312MC NTE0315MC NTE0503MC NTE0505MC NTE0505MEC Start-up time μs 437 1359 3435 6590 7625 533 1368 721 NTE0506MC NTE0509MC NTE0512MC NTE0515MC NTE1205MC NTE1209MC NTE1212MC NTE1215MC Start-up time μs 7200 3146 4960 7740 895 2150 3640 7180 Typical Start-Up Wave Form www.murata-ps.com/support KDC_NTE.K03 Page 3 of 6 NTE Series Isolated 1W Single Output SM DC/DC Converters APPLICATION NOTES (continued) Output Ripple Reduction By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max. Component selection Capacitor: It is required that the ESR (Equivalent Series Resistance) should be as low as possible, ceramic types are recommended. The voltage rating should be at least twice (except for 15V output), the rated output voltage of the DC/DC converter. Inductor: The rated current of the inductor should not be less than that of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF (Self Resonant Frequency) should be >20MHz. L DC Power Source NTE0303MC NTE0305MC NTE0309MC NTE0312MC NTE0315MC NTE0503MC NTE0505MC NTE0505MEC NTE0506MC NTE0509MC NTE0512MC NTE0515MC NTE1205MC NTE1209MC NTE1212MC NTE1215MC L, μH 10 47 22 10 47 10 47 47 10 22 47 47 47 22 47 47 Inductor SMD 82103C 82473C 82223C 82103C 82473C 82103C 82473C 82473C 82103C 82223C 82473C 82473C 82473C 82223C 82473C 82473C C Load DC Through Hole 11R103C 11R103C 11R223C 11R103C 11R473C 11R103C 11R473C 11R473C 11R103C 11R223C 11R473C 11R473C 11R473C 11R223C 11R473C 11R473C Capacitor C, μF 4.7 4.7 2.2 1 1 4.7 4.7 4.7 4.7 2.2 1 1 4.7 2.2 1 1 www.murata-ps.com/support KDC_NTE.K03 Page 4 of 6 NTE Series Isolated 1W Single Output SM DC/DC Converters PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS PIN CONNECTIONS 12.70 (0.500) 7.62 (0.300) 14 11.20 (0.441) 7.70 (0.303) 10.40 (0.409) 10 12 DETAIL A 8 NTE0505MC P XYYWW 1 3 5 1.50 (0.059) 1.20 (0.047) 7 0.65 (0.026) 0.55 (0.022) 2.54 (0.100) 10 PINS 0.2 (0.008) ±5.00° Function 1 3 5 7 8 10 -VIN +VIN NA -VOUT +VOUT NA NA NA 12 14 S 2.10 (0.083) DETAIL A NA - Not available for electrical connection. 6.60 (0.260) 6.35 (0.250) 5.95 (0.234) 5.85 (0.230) 2.79 (0.110) MAX 0.50 (0.020) REFERENCE PLANE Pin S 0.25 (0.010) 0.10 (0.004) 1.875 MAX 0.1(0.004) S All dimensions in mm ±0.25mm (inches ±0.01). All pins on a 2.54 (0.1) pitch and within ± 0.25 (0.01) of true position. 0.30 (0.012) 0.20 (0.008) Weight: 1.21g TUBE OUTLINE DIMENSIONS RECOMMENDED FOOTPRINT DETAILS 7.62 (0.3) SEATING PLANE 0.60±0.15 (0.024±0.006) 2.10 (0.083) 2.00 (0.079) 9.70 (0.382) 9.40 (0.370) 14.35 (0.565) 2.54 (0.1) 1.00 (0.040) MIN All pins on a 2.54mm pitch. Unless otherwise stated all dimensions in mm (inches) ±0.5mm. 6.70 (0.264) Unless otherwise stated all dimensions in mm±0.5mm (inches ±0.02). Tube length : 475±2.0 (18.70±0.07). Tube Quantity : 35 www.murata-ps.com/support KDC_NTE.K03 Page 5 of 6 NTE Series Isolated 1W Single Output SM DC/DC Converters TAPE & REEL SPECIFICATIONS REEL OUTLINE DIMENSIONS TAPE OUTLINE DIMENSIONS 330 (12.99) MAX 13.20 (0.52) 0.60 (0.02) MAX 100 Ø (3.94) MIN +0.004 (+0.10) -0.00 (-0.00) DIRECTION OF UNREELING 13.00±0.25 Ø (0.51±0.009) 2.00 (0.08) 30.40 (1.20) MAX 2.00(+0.08) (AT HUB SECTION) 24.40 (0.96) -0.00 (0.00) 1.50 (Ø0.06) 16.00 (0.63) 11.60 (0.46) 4.00 (0.16) 1.75(0.07) 11.50 (0.45) 24.00±0.30 (0.94±0.04) 6.60 (0.26) REEL PACKAGING DETAILS XYYWW Product Orientation Pin 1, located nearest to carrier drive sprocket. NTE0505MC XYYWW NTE0505MC XYYWW NTE0505MC TRAILER SECTION 160 (6.30) MIN GOODS ENCLOSURE SECTION CARRIER TAPE START 100 (3.94) MIN LEADER SECTION 400 (15.75) MIN Reel Quantity : 500 Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. ISO 9001 and 14001 REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: http://www.murata-ps.com/requirements/ Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2012 Murata Power Solutions, Inc. www.murata-ps.com/support KDC_NTE.K03 Page 6 of 6