GI820 THRU GI828 FAST SWITCHING PLASTIC RECTIFIER Reverse Voltage - 50 to 800 Volts FEATURES Case Style P600 ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ High forward current operation ♦ Fast switching for high efficiency ♦ Construction utilizes void-free molded plastic technique ♦ Uniform molded body ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.360 (9.1) 0.340 (8.6) 0.360 (9.1) 0.340 (8.6) 0.052 (1.32) 0.048 (1.22) DIA. Forward Current - 5.0 Amperes MECHANICAL DATA 1.0 (25.4) MIN. Case: Void-free molded plastic body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.07 ounce, 2.1grams Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GI820 GI821 GI822 GI824 GI826 GI828 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 Volts VDC 50 100 200 400 600 800 Volts Maximum non-repetitive peak reverse voltage VRSM 75 150 250 450 650 880 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at T A=55°C I(AV) 5.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 300.0 Amps Maximum instantaneous forward voltage at 5.0A TJ= 25°C at 15.7A TJ=150°C VF 1.10 1.05 Volts TA= 25°C TA=100°C IR 10.0 1.0 µA mA Typical junction capacitance (NOTE 1) CJ 300.0 pF Maximum reverse recovery time (NOTE 2) trr 200.0 ns IRM(REC) 2.0 Amps RΘJA 10.0 °C/W TJ, TSTG -50 to +150 °C Maximum DC blocking voltage Maximum reverse current at rated DC blocking voltage Maximum reverse recovery current (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range NOTES: (1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (2) Reverse recovery test conditions: IF=1.0A, VR=30V, di/dt=50A/µs, and Irr=10% IRM for measurement of trr (3) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, with both leads equally to heat sink 4/98 RATINGS AND CHARACTERISTIC CURVES GI820 THRU GI828 FIG.1 - FORWARD CURRENT DERATING CURVE FIG. 2 - FORWARD CURRENT DERATING CURVE 20 5.0 AVERAGE FORWARD CURRENT, AMPERES CAPACITIVE LOADS 5.0 I(pk) 10 I(AV) 20 Ipk/IAV=π 6.0 4.0 3.0 2.0 1.0 0 20 1.1 x 1.1” (30 x 30mm) COPPER PADS 40 60 80 100 120 140 160 RESISTIVE OR INDUCTIVE LOAD L= LEAD LENGTH 16 L=0 .12 12 L=0 ”(3. .25” 8.0 1.6” x 1.6” x 0.04” (40mm x 40mm x 1mm) COPPER HEATSINK 2m (6.3 m) mm L=0.3 ) 75”(9.5 L=0.62”( 15.9mm 4.0 0 75 180 mm) 85 ) 95 105 115 125 135 145 155 165 175 AMBIENT TEMPERATURE, °C LEAD TEMPERATURE, °C FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 PEAK FORWARD SURGE CURRENT, AMPERES 400 INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 350 TA=25°C 300 250 TJ=125°C 200 150 100 1 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 1 100 0.1 0.6 NUMBER OF CYCLES AT 60 Hz 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL REVERSE CHARACTERISTICS FIG. 6 - TYPICAL THERMAL RESISTANCE 10 25 RΘJL, THERMAL RESISTANCE FROM JUNCTION TO LEAD, °C/W INSTANTANEOUS REVERSE CURRENT, MICROAMPERES AVERAGE FORWARD CURRENT, AMPERES 7.0 TJ=100°C 1 TJ=50°C 0.1 TJ=25°C 0.01 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100 L= LEAD LENGTH 20 15 10 5.0 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 EQUAL LEAD LENGTHS TO HEAT SINK, INCHES 1.0