Series AM50E-NZ 50 Watt | DC-DC Converter Picture coming soon FEATURES: • • • • • • • • Wide Input range 2:1 High Efficiency up to 93% Remote On/Off Control Trim Adjustment Input to Output Isolation of 1500VDC Input Over Voltage and Under Voltage Lockout Output OVP, OCP & SCP Operating Temperature -40 to +85°C Models Single output Model Input Voltage (V) Output Voltage (V) Output Current max (A) No load Input Current (mA) Max Capacitive Load(uF) Efficiency (%) AM50E-2403S-NZ 18-36 3.3 10 70 27000 91 AM50E-2405S-NZ 18-36 5 10 70 18900 93 AM50E-2412S-NZ 18-36 12 4.167 70 3700 93 AM50E-2415S-NZ 18-36 15 3.333 70 2000 93 AM50E-2424S-NZ 18-36 24 2.083 70 1000 93 AM50E-4803S-NZ 36-75 3.3 10 50 27000 91 AM50E-4805S-NZ 36-75 5 10 50 18900 93 AM50E-4812S-NZ 36-75 12 4.167 50 3700 93 AM50E-4815S-NZ 36-75 15 3.333 50 2000 93 AM50E-4824S-NZ 36-75 24 2.083 50 1000 93 Add suffix “-K” for optional heatsink NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Nominal 24 48 Filter Start up time Absolute Maximum Rating 24 48 Peak Input Voltage time On/Off control* Input Current Over Voltage Lockout Under Voltage Lockout Input reflected current 24 48 24 48 24 48 24 48 Typical Maximum Units 18-36 36-75 π(Pi) Network 10 VDC ms -0.7 ~ 50 -0.7 ~ 100 1 ON – open or TTL high (3 - 12VDC) ; OFF – connected to GND or TTL low (0 - 1.2VDC) 2.24 1.12 40 81 16 32 40 30 VDC s A VDC VDC mA *The voltage on the On/Off Control pin is relative to input Ground. Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance www.aimtec.com F 051e R13 Conditions Typical Rated Units 1 min, ≤1mA Isolation 500VDC 100kHz, 0.1V 1500 >1000 2000 1500 VDC MOhm pF Tel: +1 514 620 2722 1 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter Output Specifications Parameters Conditions Typical Voltage accuracy Maximum ±2 % 3.3V output 5V output 12V output 15V output 24V output Over voltage protection* Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Voltage adjustment range Transient recovery time Transient recovery deviation *Restart needed to function properly 3.9 6.2 15 18 30 LL-HL 10-100% load 20MHz Bandwidth 25% load step 25% load step Units 135 Hiccup, continuous Auto-restart ±0.3 ±0.5 ±0.02 120 ±10 400 ±4 VDC % % of Vin % o %/ C mV p-p % µS % General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Conditions Typical 100% load See derating curve 300 Maximum Units 105 KHz o C o C o C -40 to +85 -55 to +125 Free Air Convection 95 % RH Aluminum alloy Without heatsink 35 g With heatsink 43 Without heatsink 2 x 1 x 0.46 inches 50.8 x 25.4 x 11.8 mm With heatsink 2 x 1 x 0.64 inches 50.8 x 25.4 x 16.3 mm >1 000 000 hrs ( MIL-HDBK-217 F at +25 °C) o 10sec, 1.5mm from case 300 C Environmental Specifications Parameters Test mode Acceleration Vibration Converter operation 10-55Hz 10G, 30min one cycle, every axis tested Before and after test, body mounted (on chassis) Safety Specifications Parameters Standards Information Technology Equipment Electrostatic Discharge Immunity RF, Electromagnetic Field Immunity Electrical Fast Transient / Burst Immunity Surge Immunity RF, Conducted Disturbance Immunity www.aimtec.com F 051e R13 EN55022 Class B, with the recommended circuit below, EN55024 IEC 61000-4-2, Contact ±4KV, Criteria B IEC 61000-4-3, 10V/m, Criteria A IEC 61000-4-4, ±2KV, Criteria B, with the recommended circuit below IEC 61000-4-5, ±2KV, Criteria B, with the recommended circuit below IEC 61000-4-6, 3 Vrms, Criteria A Tel: +1 514 620 2722 2 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter Pin Out Specifications Pin 1 2 3 4 5 6 Single +V Input -V Input On/Off Control +V Output -V Output Trim 4 5 Bottom View 3 11.80 (0.47) 2.54 (0.10) 2.54 (0.10) Notes: All dimensions are typical in millimeters (inches). Pin Pitch Tolerance ±0.35 (±0.014) Case Tolerance ±0.50 (±0.02) 4.10 (0.16) Ø1.00 (0.04) 6 10.16 (0.40) 25.40 (1.00) 1 2 10.16 (0.40) 2.54 (0.10) 5.08 (0.20) 5.08 (0.20) 50.80 (2.00) 10.16 (0.40) Dimensions Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. www.aimtec.com F 051e R13 Tel: +1 514 620 2722 3 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter AM50E-xx03S-NZ Trim down % 1 Vout (VDC) 3.27 Rt down (KΩ) 236.27 Trim up % 1 Vout (VDC) 3.33 Rt up (KΩ) 263.512 2 3.23 106.095 2 3.37 81.826 3 3.20 71.347 3 3.40 50.017 4 3.17 51.633 4 3.43 33.939 5 3.14 38.931 5 3.47 21.804 6 3.10 27.676 6 3.50 16.033 7 3.07 21.71 7 3.53 11.826 8 3.04 17.076 8 3.56 8.624 9 3.00 12.299 9 3.60 5.38 10 2.97 9.457 10 3.63 3.447 AM50E-xx05S-NZ Trim down % 1 Vout (VDC) 4.95 Rt down (KΩ) 128.53 Trim up % 1 Vout (VDC) 5.05 Rt up (KΩ) 131.399 2 4.9 56.78 2 5.1 59.65 3 4.85 32.863 3 5.15 35.733 4 4.8 20.905 4 5.2 23.775 5 4.75 13.73 5 5.25 16.6 6 4.7 8.947 6 5.3 11.817 7 4.65 5.53 7 5.35 8.4 8 4.6 2.968 8 5.4 5.838 9 4.55 0.974 9 5.45 3.844 10 4.5 -0.62 10 5.5 2.25 AM50E-xx12S-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 11.88 11.76 11.64 11.52 11.4 11.28 11.16 11.04 10.92 10.8 489.091 294.452 205.527 154.585 121.573 98.442 81.332 68.164 57.716 49.223 1 2 3 4 5 6 7 8 9 10 12.12 12.24 12.36 12.48 12.6 12.72 12.84 12.96 13.08 13.2 699.444 151.922 76.879 47.075 31.077 21.095 14.274 9.317 5.552 2.595 Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) AM50E-xx15S-NZ Trim down % Vout (VDC) Rt down (KΩ) Trim up % Vout (VDC) Rt up (KΩ) 1 14.85 1213 1 15.15 2 14.7 588 2 15.3 3 14.55 379.667 3 15.45 4 14.4 275.5 4 15.6 5 14.25 213 5 15.75 6 14.1 171.333 6 15.9 7 13.95 141.571 7 16.05 8 13.8 119.25 8 16.2 9 13.65 101.889 9 16.35 10 13.5 88 10 16.5 228 103.001 61.333 40.5 28 19.667 13.714 9.25 5.778 3 AM50E-xx24S-NZ Trim down % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 23.76 23.52 23.28 23.04 22.8 22.56 22.32 22.08 21.84 21.6 Rt down (KΩ) 1038.048 638.015 455.256 350.553 282.702 235.159 199.993 172.928 151.453 133.999 Trim up % 1 2 3 4 5 6 7 8 9 10 Vout (VDC) 24.24 24.48 24.72 24.96 25.2 25.44 25.68 25.92 26.16 26.4 Rt up (KΩ) 640.98 143.116 74.892 47.797 33.252 24.178 17.977 13.47 10.047 7.359 www.aimtec.com F 051e R13 Tel: +1 514 620 2722 4 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM50E-NZ 50 Watt | DC-DC Converter Derating For 3.3 & 5V output models: For 12, 15 & 24V output models Free Air Convection Free Air Convection 55 º C without heat sink 60 º C without heat sink 100 100 70º C with heat sink Output Power (%) Output Power (%) 65º C with heat sink 80 Safe Operating Area 60 40 80 Safe Operating Area 60 40 20 20 0 0 - 40 - 20 0 20 40 60 80 85 100 - 40 - 20 0 20 40 60 80 85 100 Ambient Temperature º C Ambient Temperature º C EMC recommended circuit Y1 LCM 2.2mH 1nF/2KV +Vo +Vin C1 330µF -Vin C2 DC-DC Converter Vout C2 (µF) 3.3 & 5V 12 & 15V 24V 220 100 47 -Vo Y2 1nF/2KV NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4 . All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R13 Tel: +1 514 620 2722 5 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only