TSC FR101S 1.0 amp. fast recovery rectifier Datasheet

FR101S - FR107S
1.0 AMP. Fast Recovery Rectifiers
A-405
Features
High efficiency, Low VF
High current capability
High reliability
High surge current capability
Low power loss.
Mechanical Data
Cases: Molded plastic
Epoxy: UL 94V-0 rate flame retardant
Lead: Pure tin plated, Lead free., solderable
per MIL-STD-202, Method 208 guaranteed
Polarity: Color band denotes cathode end
High temperature soldering guaranteed:
260oC/10 seconds/.375”,(9.5mm) lead
lengths at 5 lbs.,(2.3kg) tension
Weight: 0.22gram
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25 oC ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified
Current .375”(9.5mm) Lead Length
o
@T A = 55 C
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@ 1.0A
Maximum DC Reverse Current @ T A=25 oC
o
at Rated DC Blocking Voltage @ TA=125 C
Maximum Reverse Recovery Time ( Note 1 )
Typical Junction Capacitance ( Note 2 )
Typical Thermal Resistance
Operating Temperature Range
Symbol
VRRM
VRMS
VDC
FR
FR
FR
FR
FR
FR
FR Units
101S 102S 103S 104S 105S 106S 107S
50
100 200 400 600 800 1000
V
35
70
140 280 420 560 700
V
50
100 200 400 600 800 1000
V
I(AV)
1.0
A
IFSM
30
A
VF
1.2
V
IR
5.0
150
uA
uA
nS
pF
o
C/W
o
C
o
C
Trr
Cj
R θJA
TJ
150
250
10
90
-65 to +150
-65 to +150
Storage Temperature Range
T STG
1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
Notes:
2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C.
3. Mount on Cu-Pad Size 5mm x 5mm on P.C.B.
500
Version: A06
RATINGS AND CHARACTERISTIC CURVES (FR101S THRU FR107S)
FIG.1- MAXIMUM FORWARD CURRENT DERATING
CURVE
FIG.2- TYPICAL REVERSE CHARACTERISTICS
PER LEG
1000
0.75
0.5
INSTANTANEOUS REVERSE CURRENT. ( A)
AVERAGE FORWARD CURRENT. (A)
1.0
Single Phase
Half Wave 60Hz
Resistive or
Inductive Load
0.375" (9.5mm)
Lead Length
0.25
0
0
25
50
75
100
125
150
175
o
AMBIENT TEMPERATURE. ( C)
FIG.3- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT
100
Tj=125 0C
10
Tj=75 0C
1.0
Tj=25 0C
PEAK FORWARD SURGE CURRENT. (A)
50
0.1
0
40
30
40
60
80
100
120
140
8.3ms Single Half Sine Wave
JEDEC Method
20
FIG.5- TYPICAL FORWARD CHARACTERISTICS
20
10
10
0
2
4
6 8 10
20
NUMBER OF CYCLES AT 60Hz
40
60 80 100
INSTANTANEOUS FORWARD CURRENT. (A)
1
FIG.4- TYPICAL JUNCTION CAPACITANCE
90
JUNCTION CAPACITANCE.(pF)
20
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
50
30
20
0
Tj=25 C
10
3
Tj=25oC
Pulse Width=300 s
1% Duty Cycle
1
0.3
0.1
0.03
1
1
2
4
6
10
20
40
60
0.01
0.4
100
0.6
REVERSE VOLTAGE. (V)
0.8
1.0
1.2
1.4
1.6
1.8
FORWARD VOLTAGE. (V)
FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50
NONINDUCTIVE
10
NONINDUCTIVE
trr
+0.5A
(+)
50Vdc
(approx)
(-)
(-)
DUT
PULSE
GENERATOR
(NOTE 2)
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
0
-0.25A
(+)
-1.0A
1cm
SET TIME BASE FOR
5/ 10ns/ cm
Version: A06
Similar pages