Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor’s system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to [email protected]. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. FAN5354 3 MHz, 3 A Synchronous Buck Regulator Features Description 3 MHz Fixed-Frequency Operation Minimum PFM Frequency Avoids Audible Noise The FAN5354 is a step-down switching voltage regulator that delivers an adjustable output from an input voltage supply of 2.7 V to 5.5 V. Using a proprietary architecture with synchronous rectification, the FAN5354 is capable of delivering 3 A at over 85% efficiency, while maintaining a very high efficiency of over 80% at load currents as low as 2 mA. The regulator operates at a nominal fixed frequency of 3 MHz, which reduces the value of the external components to 470 nH for the output inductor and 10 µF for the output capacitor. Additional output capacitance can be added to improve regulation during load transients without affecting stability and inductance up to 1.2 µH may be used with additional output capacitance. Power Good Output Best-in-Class Load Transient 3 A Output Current Capability 2.7 V to 5.5 V Input Voltage Range Adjustable Output Voltage: 0.8 to 2.0 V PFM Mode for High Efficiency in Light Load (Forced PWM Available on MODE Pin) 270 µA Typical Quiescent Current in PFM Mode External Frequency Synchronization Low Ripple Light-Load PFM Mode with Forced PWM Control Internal Soft-Start Input Under-Voltage Lockout (UVLO) Thermal Shutdown and Overload Protection 12-Lead 3x3.5 mm MLP At moderate and light loads, pulse frequency modulation (PFM) is used to operate the device in power-save mode with a typical quiescent current of 270 µA. Even with such a low quiescent current, the part exhibits excellent transient response during large load swings. At higher loads, the system automatically switches to fixed-frequency control, operating at 3 MHz. In shutdown mode, the supply current drops below 1 µA, reducing power consumption. PFM mode can be disabled if constant frequency is desired. To avoid audible noise, the regulator limits its minimum PFM frequency. The FAN5354 is available in 12-lead 3x3.5 mm MLP package. Applications Set-Top Box Hard Disk Drive Communications Cards DSP Power Figure 1. Typical Application Ordering Information Part Number Temperature Range Package Packing Method FAN5354MPX -40 to 85°C MLP-12, 3 x 3.5 mm Tape and Reel © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator December 2012 Component Description Vendor Parameter Typ. Units L 0.47 H L1 470 nH Nominal IHLP1616ABER47M01 (Vishay) SD12-R47-R (Coiltronics) VLC5020T-R47N (TDK) (TDK) LQH55PNR47NT0 (Murata) DCR 20 m COUT 2 Pieces 10 F, 6.3 V, X5R, 0805 C 10.0 F CIN 10 F, 6.3 V, X5R, 0805 GRM21BR60J106M (Murata) C2012X5R0J106M (TDK) CIN1 10 nF, 25 V, X7R, 0402 GRM155R71E103K (Murata) C1005X7R1E103K (TDK) C 10 nF CVCC 4.7 F, 6.3 V, X5R, 0603 GRM188R60J475K (Murata) C1608X5R0J475K (TDK) C 4.7 F R3(1) Resistor: 1 0402 Any R 1 Note: 1. R3 is optional and improves IC power supply noise rejection. See Layout recommendations for more information. Pin Configuration FB 1 12 MODE VOUT 2 PGND 3 PGND 4 11 PGOOD 10 EN P1 (GND) 9 VCC SW 5 8 PVIN SW 6 7 PVIN Figure 2. 12-Pin, 3 x 3.5 mm MLP (Top View) Pin Definitions Pin # Name Description FB. Connect to resistor divider. The IC regulates this pin to 0.8 V. 1 FB 2 VOUT VOUT. Sense pin for VOUT. Connect to COUT. 3, 4 PGND Power Ground. Low-side MOSFET is referenced to this pin. CIN and COUT should be returned with a minimal path to these pins. 5, 6 SW P1 GND Ground. All signals are referenced to this pin. 7, 8 PVIN Power Input Voltage. Connect to input power source. Connect to CIN with minimal path. 9 VCC IC Bias Supply. Connect to input power source. Use a separate bypass capacitor CVCC from this pin to the P1 GND terminal between pins 1 and 12. 10 EN 11 PGOOD 12 MODE Switching Node. Connect to inductor. (2) Enable. The device is in shutdown mode when this pin is LOW. Do not leave this pin floating. Power Good. This open-drain pin pulls LOW if the output falls out of regulation or is in soft-start. MODE / Sync. A logic 0 allows the IC to automatically switch to PFM during light loads. When held HIGH, the IC to stays in PWM mode. The regulator also synchronizes its switching frequency to the frequency provided on this pin. Do not leave this pin floating. Note: 2. P1 is the bottom heat-sink pad. Ground plane should flow through pins 3, 4, and P1 and can be extended through pin 11 if PGOOD’s function is not required, and through pin 12 if MODE is to be grounded, to improve IC cooling. © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 2 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Table 1. Recommended External Components for 3 A Maximum Load Current Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter VIN SW, PVIN, VCC Pins Min. Max. IC Not Switching -0.3 7.0 IC Switching -0.3 6.5 -0.3 VCC + 0.3(3) V 15 V/ms Other Pins VINOV_SLEW Maximum Slew Rate of VIN Above 6.5 V, PWM Switching RPGOOD Pull-Up Resistance from PGOOD to VCC 1 Units V k Human Body Model per JESD22-A114 2 Charged Device Model per JESD22-C101 2 ESD Electrostatic Discharge Protection Level TJ Junction Temperature –40 +150 °C TSTG Storage Temperature –65 +150 °C +260 °C TL Lead Soldering Temperature, 10 Seconds kV Note: 3. Lesser of 7.0 V or VCC+0.3 V. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol Parameter Min. Typ. Max. Units VCC, VIN Supply Voltage Range 2.7 5.5 V VOUT Output Voltage Range 0.8 2.0 V IOUT Output Current 0 3 A L CIN COUT Inductor 0.47 µH Input Capacitor 10 µF Output Capacitor 20 μF TA Operating Ambient Temperature -40 +85 °C TJ Operating Junction Temperature -40 +125 °C Thermal Properties Symbol JA Parameter (4) Junction-to-Ambient Thermal Resistance Typical Units 46 °C/W Note: 4. Junction-to-ambient thermal resistance is a function of application and board layout. This data is measured with four-layer 1s2p boards in accordance to JESD51- JEDEC standard. Special attention must be paid not to exceed junction temperature TJ(max) at a given ambient temperate TA. © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 3 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Absolute Maximum Ratings Minimum and maximum values are at VIN=2.7 V to 5.5 V, TA=-40°C to +85°C, unless otherwise noted. Typical values are at TA=25°C, VIN=5 V. Symbol Parameter Conditions Min. Typ. Max. Units Power Supplies IQ I SD VUVLO Quiescent Current Shutdown Supply Current Under-Voltage Lockout Threshold ILOAD=0, MODE=0 270 A ILOAD=0, MODE=1 (Forced PWM) 14 mA EN=GND 0.1 3.0 A VIN Rising 2.83 2.95 V 2.30 2.40 V VIN Falling 2.10 VUVHYST Under-Voltage Lockout Hysteresis 530 mV Logic Pins VIH HIGH-Level Input Voltage VIL LOW-Level Input Voltage VLHYST IIN 1.05 0.4 Logic Input Hysteresis Voltage Input Bias Current V 100 0.01 1.00 A 1 mA 0.01 1.00 A 0.792 0.800 0.808 V 0.788 0.800 0.812 V Input Tied to GND or VIN IOUTL PGOOD Pull-Down Current VPGOOD=0.4 V IOUTH PGOOD HIGH Leakage Current VPGOOD=VIN V mV VOUT Regulation TA=25°C VREF Output Reference DC Accuracy Measured at FB Pin VREG VOUT DC Accuracy At VOUT Pin W.R.T. Calculated Value, ILOAD=500 mA VOUT ILOAD Load Regulation IOUT(DC)=1 to 3 A –0.03 %/A VOUT VIN Line Regulation 2.7 V ≤ VIN ≤ 5.5 V, IOUT(DC)=1.5 A 0.01 %/V Transient Response ILOAD Step 0.1 A to 1.5 A, tr=tf=100 ns, VOUT=1.2 V ±40 mV 1.6 +1.6 % Power Switch and Protection RDS(ON)P P-Channel MOSFET On Resistance 60 mΩ RDS(ON)N N-Channel MOSFET On Resistance 40 mΩ ILIMPK P-MOS Peak Current Limit TLIMIT Thermal Shutdown 3.75 150 °C THYST Thermal Shutdown Hysteresis 20 °C VSDWN Input OVP Shutdown Rising Threshold 4.55 5.50 A 6.2 V 5.50 5.85 V 2.7 3.0 3.3 MHz External Square-Wave, 30% to 70% Duty Cycle 2.7 3.0 3.3 MHz TA = 25°C, VIN = 5.0 V 17 26 36 kHz RLOAD > 5 , to VOUT=1.2 V 210 250 s RLOAD > 5 , to VOUT=1.8 V 340 420 s Falling Threshold Frequency Control fSW fSYNC Oscillator Frequency MODE Pin Synchronization Range fPFM(MIN) Minimum PFM Frequency Soft-Start tSS VSLEW Regulator Enable to Regulated VOUT Soft-Start VREF Slew Rate © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 10 V/ms www.fairchildsemi.com 4 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Electrical Characteristics Unless otherwise specified, VIN=5 V, VOUT=1.2 V, circuit of Figure 1, and components per Table 1. 90% 80% 80% 70% 70% 60% 60% Efficiency 100% 90% Efficiency 100% 50% 40% VIN = 3.3V, Mode=0 30% VIN = 3.3V, Mode=1 VIN = 5V, Mode=0 20% VIN = 5V, Mode=1 10% 50% VIN = 3.3V, Mode = 0 40% VIN = 3.3V, Mode = 1 30% VIN = 5V, Mode = 0 20% VIN = 5V, Mode = 1 10% 0% 0% 1 10 100 1000 1 10000 10 Figure 3. Efficiency vs. ILOAD at VOUT=1.2 V 1000 10000 Figure 4. Efficiency vs. ILOAD at VOUT=1.8 V 350 1 PFM, No load supply Current(µA) 0.9 0.8 Supply Current (A) 100 I LOAD Output Current (mA) I LOAD Output Current (mA) 0.7 0.6 0.5 85°C 0.4 25°C 0.3 ‐40°C 0.2 325 300 275 250 85°C 225 25°C –40°C 0.1 200 0 2.7 2.7 3.2 3.7 4.2 4.7 5.2 3.2 3.7 4.2 4.7 5.2 Input Voltage(V) Input Voltage(V) Figure 5. Shutdown Supply Current vs. VIN, EN=0 Figure 6. Quiescent Current in PFM vs. VIN, No Load 800 1.2VOUT boundary 700 Always PWM 1.2VOUT boundary Load Current (mA) 600 500 Hysteresis 400 300 200 Always PFM 100 0 2.7 3.2 3.7 4.2 4.7 5.2 Input Voltage(V) Figure 7. PFM / PWM Mode-Change Boundaries © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 5 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Typical Characteristics Unless otherwise specified, VIN=5 V, VOUT=1.2 V, circuit of Figure 1, and components per Table 1. PFM 16 PWM 90 Attenuation (dB) 12 10 8 PSRR VOUT ripple (mVAC p-p) 14 6 4 5VIN, 1.2VOUT 3.3VIN, 1.2VOUT 2 1 10 70 60 50 1.2VOUT,1.5A load 40 30 0 0.1 80 100 1000 20 10000 0.01 Load Current(mA) 0.1 1 10 100 Frequency (KHz) Figure 8. Output Voltage Ripple vs. Load Current (See explanation on page 12) Figure 9. Power Supply Rejection Ratio (PSRR) VOUT IL Figure 10. PFM-to-PWM Mode Transition, Slowly Increasing Load Current, 2 µs/div. Figure 11 PWM-to-PFM Mode Transition, Slowly Decreasing Load Current, 2 µs/div. Switching Frequency (Khz) 31.0 30.0 TJ = 85°C 29.0 TJ = 25°C TJ = –40°C 28.0 27.0 26.0 25.0 24.0 2.5 3 3.5 4 4.5 5 5.5 6 Input Voltage (V) Figure 12. PFM frequency, ILOAD = 0 © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 6 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Typical Characteristics Unless otherwise specified, VIN=5 V, VOUT=1.2 V, circuit of Figure 1, and components per Table 1. Load Transient Response (Figure 13 – Figure 16). ILOAD tR = tF = 100 ns Figure 13. MODE=0, 100 mA to 1.5 A to 100 mA, 5 µs/div. Figure 14. 500 mA to 3 A to 500 mA, 5 µs/div. VOUT IL I load Figure 15. MODE=1, 100 mA to 1.5 A to 100 mA, 5 µs/div. Figure 16. 24 mA to 500 mA to 24 mA, MODE=0, 5 µs/div. VEN VIN=VEN VOUT VOUT VPG VPG Isupply Isupply Figure 17. Soft-Start, EN Voltage Raised After VIN=5 V, ILOAD=0, 100 s/div. © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 Figure 18. Soft-Start, EN Pin Tied to VCC ILOAD=0, 1 ms/div. www.fairchildsemi.com 7 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Typical Characteristics Unless otherwise specified, VIN=5 V, VOUT=1.2 V, circuit of Figure 1, and components per Table 1. Figure 19. Soft-Start, EN Pin Raised After VIN=5 V RLOAD=400 m, COUT=100 F, 100 s/div. Figure 20. Soft-Start, EN Pin Tied to VCC RLOAD=400 m, COUT=100 F, 1 ms/div. Figure 21. Line Transient Response in PWM Mode, 10 s/div. Figure 22. Line Transient Response in PFM Mode, 10 s/div. © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 8 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Typical Characteristics Unless otherwise specified, VIN=5 V, VOUT=1.2 V, circuit of Figure 1, and components per Table 1. Circuit Protection Response VOUT VOUT IL IL VPG VPG Figure 23. VOUT to GND Short Circuit, 200 s/div. Figure 24. VOUT to GND Short Circuit, 5 s/div. VEN VOUT VOUT IL IL VPG VPG Figure 26. Progressive Overload, 200 s/div. Figure 25. Over-Current at Startup, RLOAD=200 m, 50 s/div. © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 9 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Typical Characteristics down and waits 1200 s before attempting a restart. If the regulator is at its current limit for more than about 60 s, the regulator shuts down before restarting 1200 s later. This limits the COUT capacitance when a heavy load is applied during the startup. For a typical FAN5354 starting with a resistive load: The FAN5354 is a step-down switching voltage regulator that delivers an adjustable output from an input voltage supply of 2.7 V to 5.5 V. Using a proprietary architecture with synchronous rectification, the FAN5354 is capable of delivering 3 A at over 80% efficiency. The regulator operates at a nominal frequency of 3 MHz at full load, which reduces the value of the external components to 470 nH for the output inductor and 20 µF for the output capacitor. High efficiency is maintained at light load with single-pulse PFM mode. COUTMAX ( F ) 400 100 ILOAD( A ) RLOAD Control Scheme Synchronous rectification is inhibited during soft-start, allowing the IC to start into a pre-charged load. The FAN5354 uses a proprietary non-linear, fixed-frequency PWM modulator to deliver a fast load transient response, while maintaining a constant switching frequency over a wide range of operating conditions. The regulator performance is independent of the output capacitor ESR, allowing for the use of ceramic output capacitors. Although this type of operation normally results in a switching frequency that varies with input voltage and load current, an internal frequency loop holds the switching frequency constant over a large range of input voltages and load currents. MODE Pin – External Frequency Synchronization Logic 1 on this pin forces the IC to stay in PWM mode. A logic 0 allows the IC to automatically switch to PFM during light loads. If the MODE pin is toggled, the converter synchronizes its switching frequency to the frequency on the mode pin (fMODE). The MODE pin is internally buffered with a Schmitt trigger, which allows the MODE pin to be driven with slow rise and fall times. An asymmetric duty cycle for frequency synchronization is permitted as long as the minimum time below VIL(MAX) or above VIH(MAX) is 100 ns. For very light loads, the FAN5354 operates in discontinuous current (DCM) single-pulse PFM mode, which produces low output ripple compared with other PFM architectures. Transition between PWM and PFM is seamless, with a glitch of less than 18 mV at VOUT during the transition between DCM and CCM modes. The regulator limits minimum PFM frequency to typically 26 kHz. PGOOD Pin The PGOOD pin is an open-drain that pin indicates that the IC is in regulation when its state is open. PGOOD pulls LOW under the following conditions: PFM mode can be disabled by holding the MODE pin HIGH. The IC synchronizes to the MODE pin frequency. When synchronizing to the MODE pin, PFM mode is disabled. Setting the output voltage The output voltage is set by the R1, R2, and VREF (0.8 V): R1 VOUT VREF R2 VREF (1) R1 0.8 VOUT 0.8 The IC has operated in cycle-by-cycle current limit for eight or more consecutive PWM cycles. 2. The circuit is disabled, either after a fault occurs, or when EN is LOW. 3. The IC is performing a soft-start. When EN is HIGH, the under-voltage lockout keeps the part from operating until the input supply voltage rises high enough to properly operate. This ensures no misbehavior of the regulator during startup or shutdown. (2) For example, for VOUT=1.2 V, R1=100 kΩ, R2=200 kΩ. Input Over-Voltage Protection (OVP) Output should not be set above 2.0 V to avoid operating the device at above 90% duty cycle. When VIN exceeds VSDWN (about 6.2 V), the IC stops switching to protect the circuitry from internal spikes above 6.5 V. An internal 40 s filter prevents the circuit from shutting down due to noise spikes. For the circuit to fully protect the internal circuitry, the VIN slew rate above 6.2 V must be limited to no more than 15 V / ms when the IC is switching. Enable and Soft Start When the EN pin is LOW, the IC is shut down, all internal circuits are off, and the part draws very little current. Raising EN above its threshold voltage activates the part and starts the soft-start cycle. During soft-start, the modulator’s internal reference is ramped slowly to minimize any large surge currents on the input and prevents any overshoot of the output voltage. The IC protects itself if VIN overshoots to 7 V during initial power-up as long as the VIN transition from 0 to 7 V occurs in less than 10 s (10% to 90%). If large values of output capacitance are used, the regulator may fail to start. If VOUT fails to achieve regulation within 320 s from the beginning of soft-start, the regulator shuts © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 1. Under-Voltage Lockout R1 must be set at or below 100 kΩ; therefore: R2 (3) where I LOAD VOUT www.fairchildsemi.com 10 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Operation Description I (6) 2 The FAN5354 is optimized for operation with L=470 nH, but is stable with inductances up to 1.2 H (nominal). The inductor should be rated to maintain at least 80% of its value at ILIM(PK). Failure to do so lowers the amount of DC current the IC can deliver. IMAX(LOAD) ILIM(PK ) A heavy load or short circuit on the output causes the current in the inductor to increase until a maximum current threshold is reached in the high-side switch. Upon reaching this point, the high-side switch turns off, preventing high currents from causing damage. 16 consecutive PWM cycles in current limit cause the regulator to shut down and stay off for about 1200 s before attempting a restart. Efficiency is affected by the inductor DCR and inductance value. Decreasing the inductor value for a given physical size typically decreases the DCR; but since ∆I increases, the RMS current increases, as do core and skin-effect losses. In the event of a short circuit, the soft-start circuit attempts to restart and produces an over-current fault after about 50 s, which results in a duty cycle of less than 10%, providing current into a short circuit. Thermal Shutdown IRMS When the die temperature increases, due to a high load condition and/or a high ambient temperature, the output switching is disabled until the temperature on the die has fallen sufficiently. The junction temperature at which the thermal shutdown activates is nominally 150°C with a 20°C hysteresis. Table 2 shows the effects of inductance higher or lower than the recommended 470 nH on regulator performance. Table 2. Effects of Increasing the Inductor Value (from 470 nH Recommended) on Regulator Performance The calculation for switching frequency is given below (4) RON = R DSON _ P DCRL Increase Decrease Degraded Output Capacitor and VOUT Ripple Application Information Note: Table 1 suggests 0805 capacitors, but 0603 capacitors may be used if space is at a premium. Due to voltage effects, the 0603 capacitors have a lower in-circuit capacitance than the 0805 package, which can degrade transient response and output ripple. Selecting the Inductor The output inductor must meet both the required inductance and the energy handling capability of the application. The inductor value affects the average current limit, the output voltage ripple, and the efficiency. Increasing COUT has no effect on loop stability and can therefore be increased to reduce output voltage ripple or to improve transient response. Output voltage ripple, ∆VOUT, is: The ripple current (∆I) of the regulator is: (5) 1 VOUT I ESR 8 C f OUT SW The maximum average load current, IMAX(LOAD) is related to the peak current limit, ILIM(PK), by the ripple current as: © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 Transient Response For space-constrained applications, a lower current rating for L1 can be used. The FAN5354 may still protect these inductors in the event of a short circuit, but may not be able to protect the inductor from failure if the load is able to draw higher currents than the DC rating of the inductor. ROFF = R DSON _ N DCRL ∆VOUT (EQ. 8) The FAN5354’s current limit circuit can allow a peak current of 5.5 A to flow through L1 under worst-case conditions. If it is possible for the load to draw that much continuous current, the inductor should be capable of sustaining that current or failing in a safe manner. where V VOUT IN L fSW IMAX(LOAD) Inductor Current Rating 1 1 fSW min , t SW(MAX) 333.3ns VOUT VIN (7) Increasing the inductor value produces lower RMS currents, but degrades transient response. For a given physical inductor size, increased inductance usually results in an inductor with lower saturation current. tON(MIN) and tOFF(MIN) are both 45 ns. This imposes constraints on the maximum VOUT that the FAN5354 can provide, VIN while still maintaining a fixed switching frequency in PWM mode. While regulation is unaffected, the switching frequency will drop when the regulator cannot provide sufficient duty cycle at 3 MHz to maintain regulation. I I2 12 The increased RMS current produces higher losses through the RDS(ON) of the IC MOSFETs as well as the inductor ESR. Minimum Off-Time Effect on Switching Frequency VOUT IOUT ROFF t SW(MAX) 45ns 1 V IN IOUT R ON VOUT IOUT(DC) 2 (8) where COUT is the effective output capacitance. The capacitance of COUT decreases at higher output voltages, which results in higher ∆VOUT . www.fairchildsemi.com 11 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Current Limiting Layout Recommendations The layout recommendations below highlight various topcopper planes by using different colors. It includes COUT3 to demonstrate how to add COUT capacitance to reduce ripple and transient excursions. The inductor in this example is the TDK VLC5020T-R47N. If an inductor value greater than 1.0 H is used, at least 30 F of COUT should be used to ensure stability. As can be seen in Figure 8 the lowest ∆VOUT is obtained when the IC is in PWM mode and, therefore, operating at 3 MHz. In PFM mode, fSW is reduced, causing ∆VOUT to increase. At extremely light loads, the output ripple decreases, as the minimum frequency circuit becomes active and the effective tON (high-side on-time) decreases. VCC and VIN should be connected together by a thin trace some distance from the IC, or through a resistor (shown as R3 below), to isolate the switching spikes on PVIN from the IC’s bias supply on VCC. If PCB area is at a premium, the connection between PVIN and VCC can be made on another PCB layer through vias. The via impedance provides some filtering for the high-frequency spikes generated on PVIN. ESL Effects The ESL (Equivalent Series Inductance) of the output capacitor network should be kept low to minimize the square wave component of output ripple that results from the division ratio COUT ESL and the output inductor (LOUT). The square wave component due to the ESL can be estimated as: VOUT ( SQ ) VIN ESLCOUT L1 PGND and AGND connect through the thermal pad of the IC. Extending the PGND and AGND planes improves IC cooling. The IC analog ground (AGND) is bonded to P1 between pins 1 and 12. Large AC ground currents should return to pins 3 and 4 (PGND) either through the copper under P1 between pins 6 and 7 or through a direct trace from pins 3 and 4 (as shown for COUT1-COUT3). (9) A good practice to minimize this ripple is to use multiple output capacitors to achieve the desired COUT value. For example, to obtain COUT=20 F, a single 22 F 0805 would produce twice the square wave ripple of 2 x 10 F 0805. EN and PGOOD connect through vias to the system control logic. To minimize ESL, try to use capacitors with the lowest ratio of length to width. 0805s have lower ESL than 1206s. If low output ripple is a chief concern, some vendors produce 0508 or 0612 capacitors with ultra-low ESL. Placing additional small value capacitors near the load also reduces the highfrequency ripple components. CIN1 is an optional device used to provide a lower impedance path for high-frequency switching edges/spikes, which helps to reduce SW node and VIN ringing. CIN should be placed as close as possible between PGND and VIN as shown below. PGND connection back to inner planes should be accomplished as series of vias distributed among the COUT return track and CIN return plane between pins 6 and 7. Input Capacitor The 10F ceramic input capacitor should be placed as close as possible between the VIN pin and PGND to minimize the parasitic inductance. If a long wire is used to bring power to the IC, additional “bulk” capacitance (electrolytic or tantalum) should be placed between CIN and the power source lead to reduce under-damped ringing that can occur between the inductance of the power source leads and CIN. The effective CIN capacitance value decreases as VIN increases due to DC bias effects. This has no significant impact on regulator performance. AGND 0402 VOUT COUT1 10F 0805 10F 0805 1 2 3 PGND L1 0.47H 5 x 5 mm 10 P1 (GND) 9 VCC 5 8 6 7 SW CIN1 CVCC 11 0402 4 12 FAN5354 0603 COUT2 10F 0805 0402 COUT3 R3 VIN 10F 0805 0402 CIN PGND Figure 27. 3 A Layout Recommendation © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 12 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator If COUT is greater than 100 F, the regulator may fail to start under load. FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator Physical Dimensions Figure 28. 12-lead 3 x 3.5 mm MLP Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 13 FAN5354 — 3 MHz, 3 A Synchronous Buck Regulator © 2009 Fairchild Semiconductor Corporation FAN5354 • Rev. 1.0.7 www.fairchildsemi.com 14 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] © Semiconductor Components Industries, LLC N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com