Continental Device India Limited An ISO/TS 16949, ISO 9001 and ISO 14001 Certified Company NPN/PNP SILICON PLANAR EPITAXIAL TRANSISTORS MPSA05,MPSA06 MPSA55,MPSA56 TO-92 Plastic Package E BC Amplifier Transistors ABSOLUTE MAXIMUM RATINGS(Ta=25°C unless otherwise specified) DESCRIPTION SYMBOL MPSA05 MPSA55 MPSA06 MPSA56 UNITS Collector Emitter Voltage VCEO 60 80 V Collector Base Voltage VCBO 60 80 V Emitter Base Voltage VEBO 4 V Collector Current Continuous IC 500 mA Total Device Dissipation@Ta=25°C Derate Above 25°C Total Device Dissipation@ Tc=25°C Derate Above 25°C Operating And Storage Junction Temperature Range PD Tj, Tstg 625 5.0 1.5 12 -55 to +150 mW mW/°C W mW/°C °C Rth(j-a) (1) 200 °C/mW Rth(j-c) Junction to case 83.3 (1) Rth(j-a) is measured with the device soldered into a typical printed circuit board. °C/mW THERMAL RESISTANCE Junction to ambient Continental Device India Limited PD Data Sheet Page 1 of 4 NPN SILICON PLANAR EPITAXIAL TRANSISTORS MPSA05,MPSA06 MPSA55,MPSA56 TO-92 Plastic Package E BC ELECTRICAL CHARACTERISTICS (Ta=25°C Unless Otherwise Specified) DESCRIPTION SYMBOL TEST CONDITION MIN Collector Emitter Voltage MPSA05/55 MPSA06/56 Emitter-Base Voltage VCEO * VEBO TYP MAX UNITS IC=1mA,IB=0 IE=100uA, IC=0 60 80 4.0 V V V ICBO Collector-Cut off Current MPSA05/55 VCB=60V, IE = 0 0.1 uA MPSA06/56 VCB=80V, IE = 0 0.1 uA VCE=60V,IB =0 0.1 uA ICEO Collector-Cut off Current Collector-Emitter (sat) Voltage VCE(sat) IC=100mA,IB=10mA 0.25 V Base-Emitter(on) Voltage DC Current Gain VBE(on) IC=100mA,VCE=1V 1.2 V uA MAX UNITS hFE VCE=1V,IC=10mA 100 VCE=1V,IC=100mA 100 ELECTRICAL CHARACTERISTICS (Ta=25°C Unless Otherwise Specified) DESCRIPTION SYMBOL TEST CONDITION MIN DYNAMIC CHARACTERISTICS Transition Frequency NPN PNP f T** IC=10mA, VCE=2V 100 MHz f=100MHz IC=100mA, VCE=1V 50 MHz f=100MHz *Pulse Test : Pulse Width < 300us, Duty Cycle < 2%. ** fT is defined as the frequency at which IhfeI extrapolates to unity. Continental Device India Limited Data Sheet Page 2 of 4 MPSA05,MPSA06 MPSA55,MPSA56 TO-92 Plastic Package TO-92 Plastic Package B TO-92 Transistors on Tape and Ammo Pack Ammo Pack Style MECHANICAL DATA A h Adhesive Tape on Top Side P T h (p) A1 LABEL A 3 2 1 H1 ED FE Carrier Strip FLAT SIDE 8.2" W2 H0 L Wo W1 W 13" t1 F1 t F2 K F 1.7 7 Do P2 " Po All dimensions in mm unless specified otherwise D A A DIM PIN CONFIGURATION 1. COLLECTOR 2. BASE 3. EMITTER All diminsions in mm. C H F 3 2 1 1 2 SEC AA G F 3 E D Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack MIN. MAX. A 4.32 5.33 B 4.45 5.20 C 3.18 4.19 D 0.41 0.55 E 0.35 0.50 F 5 DEG G 1.14 1.40 H 1.14 1.53 K 12.70 — ITEM SYMBOL BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT FEED HOLE PITCH A1 A T P Po FEED HOLE CENTRE TO COMPONENT CENTRE P2 DISTANCE BETWEEN OUTER LEADS COMPONENT ALIGNMENT TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION F h W Wo W1 HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCEF1, W2 Ho H1 L Do t F2 CLINCH HEIGHT PULL - OUT FORCE H2 (P) SPECIFICATION REMARKS MIN. NOM. MAX. TOL . 4.0 4.8 5.2 4.8 4.2 3.9 12.7 ±1 12.7 ±0.3 CUMULATIVE PITCH ERROR 1.0 mm/20 PITCH 6.35 ±0.4 TO BE MEASURED AT BOTTOM OF CLINCH +0.6 5.08 -0.2 1 0 AT TOP OF BODY 18 ±0.5 6 ±0.2 9 +0.7 -0.5 0.5 ±0.2 16 ±0.5 23.25 11.0 4 ±0.2 1.2 t1 0.3 - 0.6 2.54 +0.4 -0.1 3 6N NOTES 1. MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm. 2. MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20 PITCHES. 3. HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO EXPOSURE OF ADHESIVE. 4. NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED. 5. A TAPE TRAILER, HAVING AT LEAST THREE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT. 6. SPLICES SHALL NOT INTERFERE WITH THE SPROCKET FEED HOLES. Packing Detail PACKAGE TO-92 Bulk TO-92 T&A STANDARD PACK Details Net Weight/Qty 1K/polybag 200 gm/1K pcs 2K/ammo box 645 gm/2K pcs Continental Device India Limited INNER CARTON BOX Size Qty 3" x 7.5" x 7.5" 5.0K 12.5" x 8" x 1.8" 2.0K Data Sheet OUTER CARTON BOX Size Qty Gr Wt 17" x 15" x 13.5" 80.0K 23 kgs 17" x 15" x 13.5" 32.0K 12.5 kgs Page 3 of 4 Notes MPSA05,MPSA06 MPSA55,MPSA56 TO-92 Plastic Package Disclaimer The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as to confirm that the Device(s) meet functionality parameters for your application. The information furnished on the CDIL Web Site/CD are believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for use in life saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s). CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice. CDIL is a registered Trademark of Continental Device India Limited C-120 Naraina Industrial Area, New Delhi 110 028, India. Telephone + 91-11-2579 6150, 5141 1112 Fax + 91-11-2579 5290, 5141 1119 [email protected] www.cdilsemi.com MPS05_06_55_56REV081001 Continental Device India Limited Data Sheet Page 4 of 4