Model. No. Rev. FYLF-1130UB1C A PRODUCT SPECIFICATION Model No.： ：FYLF-1130UB1C Features: ■ Flux LED Type ■ Size (mm):Φ5*7.62*7.62 ■ Emitting Color:Blue ■ Lens Type:Water clear ■ Pb-free Reflow soldering application ■RoHS Compliant Applications: ■Indicators ■Automotive application ■Decorative lighting ■Illuminations CUSTOMER APPROVED SIGNATURES APPROVED BY NINGBO FORYARD OPTOELECTRONICS CO.,LTD Add:NO.115 Qixin Road Ningbo Zhejiang China Tel: 0086-574-87933652 87927870 87922206 Fax: 0086-574-87927917 E-mail:[email protected] ( General) CHECKED BY PREPARED BY Zip:315051 Http://www.foryard.com Http://www.foryard.com Page： 1/7 Model. No. Rev. FYLF-1130UB1C A Model No.： ：FYLF-1130UB1C ■ Mechanical Dimensions （ ） C Notes: 1. Dimension in millimeter [inch], tolerance is ±0.25 [.010] and angle is ±1° unless otherwise noted. 2. Bending≤Length*1%. 3.The specifications,characteristics and technical data described in the datasheet are subject to change without prior notice. Http://www.foryard.com Page： 2/7 FYLF-1130UB1C A Model. No. Rev. Model No.： ：FYLF-1130UB1C ■ Absolute Maximun Ratings(Ta=25º º C) Items Symbol Absolute maximum Rating Unit IF 30 mA Peak Forward Current* IFP 100 mA Power Dissipation PD 120 Mw Operation Temperature Topr -40ºC+85ºC ℃ Storage Temperature Tstg -40ºC+100ºC ℃ Reverse Voltage VR 5 V Soldering Temperature Tsol Forward Current(DC) Reflow Soldering:260℃/3sec *Pulse width≦ ≦1msec duty≦ ≦1/10 ■ Typical Electrical &Optical Charcteristics(Ta=25ºC) Items Symbol Condition Min. Typ. Max Unit Forward Voltage VF IF = 20mA 2.80 --- 3.60 V Reverse Current IR VR = 5V 5 uA Dominant Wavelength λd IF = 20mA 465 --- 475 nm Luminous Flux ΦV IF = 20mA --- 0.9 --- lm Luminous Intensity IV IF = 20mA --- 600 --- mcd 50% Power Angle 2θ½ IF = 20mA --- 90 --- Deg ■ Material Item Reflector Wire Encapsulate Chip Material Copper Gold Epoxy InGaN Note: 1.Luminous Intensity is based on the Foryard standards. 2.Pay attention about static for InGaN Http://www.foryard.com Page： 3/7 Model. No. Rev. FYLF-1130UB1C A Model No.： ：FYLF-1130UB1C ■ Typical Eletrical/Optical Characteristics Curves(Ta=25º º C Unless Otherwise Noted) O3 l2 A / N a G n I Radiation pattern. Relative Lumionous Intensity(LOP @max=1) Http://www.foryard.com Page： 4/7 Model. No. Rev. FYLF-1130UB1C A Model No.： ：FYLF-1130UB1C ■ Packing Diagram 60PCS/IC TUBE Part NO: FYLF-xxxxxxx Date:xxxx/xx/xx Q'TY: 60 PCS VF:x IV:xxx WL:xxx 600PCS/10PCS IC TUBE OUTSIDE LABEL FORYARD O P T O E L E C T R O N I C S www.foryard.com 8400PCS/140PCS IC TUBE 33600PCS/560PCS IC TUBE FORYARD O P T O E L E C T R O N I C S LED PN:FYLF-xxxxxxxx-xx Qty: 33600 PCS Date:xxxx/xx/xx GW: xx KG NW: xx KG PASS QC: QC RoHS ATTENTION xxxxxxxxxx OUTSIDE LABEL Note: The specifications are subject to change without notice. Please contact us for updated information. Http://www.foryard.com Page： 5/7 Model. No. Rev. FYLF-1130UB1C A Model No.： ：FYLF-1130UB1C ■ Precautions for use: 1. Storage Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temperature after soldering. Avoid quick cooling. Lead frames are silver plated copper alloy. The silver plate surface may be affected by environments which contains corrosive substances. Please avoid conditions which may cause the LEDs to corrode,tarnish or discolour. 2. Soldering Manual Soldering Solder Dipping Soldering Iron 35W max. Preheat Temperature 280℃ max(63/37 Solder) Preheat time 60 seconds max. 300℃ max(Pb free solder)Solder temperature 63/37 Solder:235℃(245℃max) Soldering Time 3 seconds max. Pb-free solder:255℃(260℃max) Position Not less than 3mm from Dipping Time the base of the epoxy 3 seconds max. 110℃ max Not less than 3mm from the base of the epoxy Position Recommended soldering profile: Temperature( ) 300 laminar wave 250 200 150 100 50 Preheat 0 0 10 20 30 40 50 60 70 Times(Sec) 80 90 100 110 120 Solder=Sn 63-Pb 37 Solder= Pb-Free Peak preheat temperature:100-110℃ Peak preheat temperature:100-110℃ Total preheat time:50-60seconds Total preheat time:50-60seconds Peak profile fit temperature:235℃(max 245℃) Peak profile fit temperature:260℃max Dwell time above 200℃ should not exceed 3 seconds Dwell time above 200℃ should not exceed 3 seconds Http://www.foryard.com Page： 6/7 Model. No. Rev. FYLF-1130UB1C A Model No.： ：FYLF-1130UB1C Caution: The LEDs must not be repositioned after soldering. Do not apply any stress to the lead particularly when heat. 3. Static Electricity Static Electricity and surge voltage damage the LEDs. So it is recommended that an ESD wrist band, ESD shoe strap or an anti-electrostatic glove be used when handling the LEDs. All devices, equipment and machinery must be properly grounded. 4. Others Reverse voltage should not exceed the absolute maximum rating on the data sheet. The LED leads may become tarnished if they contact hydrogen sulphide or other gaseous chemicals. The colour of the LEDs is changed slightly an operating current and thermal. This device should not be used in any type of fluid such as water, oil, organic solvent and etc. When washing is required, IPA (Isopropyl Alcohol) should be used. The influence of ultrasonic cleaning on the leds depends on factors such as ultrasonic power and the way. Gallium arsenide is used in some of the products listed in this publication. These products are dangerous if they are burned or smashed in the process of disposal, It is also dangerous to drink the liquid or inhale the ga generated by such products when chemically disposed. High-brightness LED light may injure human eyes. Avoid looking directly into lighted LED. The appearance and specifications of the product may be modified for improvement without notice. Http://www.foryard.com Page： 7/7