Not Recommended For New Designs DS96176 DS96176 RS-485/RS-422 Differential Bus Transceiver Literature Number: SNLS393A May 1998 DS96176 RS-485/RS-422 Differential Bus Transceiver General Description The DS96176 Differential Bus Transceiver is a monolithic integrated circuit designed for bidirectional data communication on balanced multipoint bus transmission lines. The transceiver meets EIA Standard RS-485 as well as RS-422A. The DS96176 combines a TRI-STATE ® differential line driver and a differential input line receiver, both of which operate from a single 5.0V power supply. The driver and receiver have an active Enable that can be externally connected to function as a direction control. The driver differential outputs and the receiver differential inputs are internally connected to form differential input/output (I/O) bus ports that are designed to offer minimum loading to the bus whenever the driver is disabled or when VCC = 0V. These ports feature wide positive and negative common mode voltage ranges, making the device suitable for multipoint applications in noisy environments. The driver is designed to handle loads up to 60 mA of sink or source current. The driver features positive and negative current-limiting and thermal shutdown for protection from line fault conditions. Thermal shutdown is designed to occur at junction temperature of approximately 160˚C. The receiver features a typical input impedance of 15 kΩ, an input sensitivity of ± 200 mV, and a typical input hysteresis of 50 mV. Connection Diagram The DS96176 can be used in transmission line applications employing the DS96172 and the DS96174 quad differential line drivers and the DS96173 and DS96175 quad differential line receivers. Features n n n n n n n n n n n n n n Bidirectional transceiver Meets EIA Standard RS-422A and RS-485 Designed for multipoint transmission TRI-STATE driver and receiver enables Individual driver and receiver enables Wide positive and negative input/output bus voltage ranges Driver output capability ± 60 mA Maximum Thermal shutdown protection Driver positive and Negative current-limiting High impedance receiver input Receiver input sensitivity of ± 200 mV Receiver input hysteresis of 50 mV typical Operates from single 5.0V supply Low power requirements Receiver 8–Lead DIP Differential Inputs Enable A-B RE Output R VID ≥ 0.2V L H VID ≤ −0.2V L L X H Z H = High Level L = Low Level X = Immaterial Z = High Impedance (off) DS009630-1 Top View Order Number DS96176CN See NS Package Number N08E Function Table Driver Input Enable DI DE A Outputs B H H H L L H L H X L Z Z TRI-STATE ® is a registered trademark of National Semiconductor Corporation. © 2001 National Semiconductor Corporation DS009630 www.national.com DS96176 RS-485/RS-422 Differential Bus Transceiver Not Recommended For New Designs DS96176 Not Recommended For New Designs Absolute Maximum Ratings (Note 2) Recommended Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) Voltage at Any Bus Terminal (Separately or Common Mode) Differential Input Voltage (VID) Output Current HIGH (IOH) Driver Receiver Output Current LOW (IOL) Driver Receiver Operating Temperature (TA) Storage Temperature Range Molded DIP −65˚C to +150˚C Lead Temperature Molded DIP (soldering, 10 sec.) 265˚C Maximum Power Dissipation (Note 1) at 25˚C Molded Package 930 mW Supply Voltage 7.0V Differential Input Voltage +15V/−10V Enable Input Voltage 5.5V Min Typ Max 4.75 5.0 5.25 −7.0 0 12 Units V ± 12 V V −60 −400 mA µA 60 16 70 mA mA ˚C 25 Note 1: Derate molded DIP package 7.5 mW/˚C above 25˚C. Electrical Characteristics (Notes 3, 4) Over recommended temperature, common mode input voltage, and supply voltage ranges, unless otherwise specified Symbol Parameter Conditions Min Typ Max Units 0.8 V DRIVER SECTION VIH Input Voltage HIGH VIL Input Voltage LOW VOH Output Voltage HIGH IOH = −20 mA 3.1 V VOL Output Voltage LOW IOL = 20 mA 0.85 V 2.0 V VIC Input Clamp Voltage II = −18 mA −1.5 V |VOD1| Differential Output Voltage IO = 0 mA 6.0 V |VOD2| Differential Output Voltage RL = 100Ω, Figure 1 2.0 2.25 RL = 54Ω, Figure 1 and Figure 2 1.5 2.0 ∆|VOD2| Change in Magnitude of RL = 54Ω Differential Output Voltage (Note 5) VCM = 0V Figure 1 and Figure 2 VOC Common Mode Output Voltage (Note 6) RL = 54Ω or 100Ω, Figure 1 ∆|VOC| Change in Magnitude of V ± 0.2 V RL = 100Ω Figure 1 3.0 V ± 0.2 V VO = 12V 1.0 mA VO = −7.0V −0.8 Common Mode Output Voltage (Note 5) IO Output Current (Note 5) Output Disabled (Includes Receiver II) IIH Input Current HIGH VI = 2.4V 20 µA IIL Input Current LOW VI = 0.4V −100 µA IOS Short Circuit Output Current VO = −7.0V −250 VO = 0V −150 VO = VCC 150 (Note 10) VO = 12V ICC Supply Current No Load mA 250 Outputs Enabled 35 Outputs Disabled 40 mA RECEIVER SECTION VTH Differential Input High VO = 2.7V, IO = −0.4 mA 0.2 V Threshold Voltage VTL Differential Input Low VO = 0.5V, IO = 8.0 mA −0.2 V Threshold Voltage (Note 7) VT+ − VT− Hysteresis (Note 8) VIH Enable Input Voltage HIGH VIL Enable Input Voltage LOW VIC Enable Input Clamp Voltage www.national.com VCM = 0V 50 mV 2.0 II = −18 mA 2 V 0.8 V −1.5 V Electrical Characteristics (Notes 3, 4) DS96176 Not Recommended For New Designs (Continued) Over recommended temperature, common mode input voltage, and supply voltage ranges, unless otherwise specified Symbol Parameter Conditions Min Typ Max Units RECEIVER SECTION VOH Output Voltage HIGH VOL Output Voltage LOW VID = 200 mV, IOH = −400 µA, 2.7 V Figure 3 VID = −200 mV, IOL = 8,0 mA 0.45 Figure 3 IOL = 16 mA 0.50 IOZ High Impedance State Output VO = 0.45V to 2.4V II Line Input Current (Note 9) Other Input = 0V IIH Enable Input Current HIGH VIH = 2.7V VIL = 0.4V IIL Enable Input Current LOW RI Input Resistance IOS Short Circuit Output Current (Note 10) ICC Supply Current (Total Package) No Load V ± 20 VI = 12V 1.0 VI = −7.0V 0.8 µA mA 20 µA −100 µA 12 kΩ −15 Outputs Enabled −85 mA 40 mA Outputs Disabled Driver Switching Characteristics VCC = 5V, TA = 25˚C Symbol Parameter Conditions Min Typ Max Units tDD Differential Output Delay Time RL = 60Ω, Figure 4 15 25 ns tTD Differential Output Transition Time RL = 60Ω, Figure 4 15 25 ns tPLH Propagation Delay Time, RL = 27Ω, Figure 5 12 20 ns tPHL Propagation Delay Time, RL = 27Ω, Figure 5 12 20 ns Low-to-High Level Output High-to-Low Level Output tPZH Output Enable Time to High Level RL = 110Ω, Figure 6 25 35 ns tPZL Output Enable Time to Low Level RL = 110Ω, Figure 7 25 35 ns tPHZ Output Disable Time from High Level RL = 110Ω, Figure 6 20 25 ns tPLZ Output Disable Time from Low Level RL = 110Ω, Figure 7 29 35 ns Typ Max Units 16 25 ns 16 25 ns 15 22 ns 15 22 ns 14 30 ns 24 40 ns Receiver Switching Characteristics VCC = 5.0V, TA = 25˚C Symbol Parameter Conditions tPLH Propagation Delay Time, VID = 0V to 3.0V Low-to-High Level Output CL = 15 pF, Figure 8 tPHL Propagation Delay Time, Min High-to-Low Level Output tPZH Output Enable Time to High Level tPZL Output Enable Time to Low Level tPHZ Output Disable Time from High Level tPLZ Output Disable Time from Low Level CL = 15 pF, Figure 9 CL = 5.0 pF, Figure 9 Note 2: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The tables of “Electrical Characteristics” provide conditions for actual operation. Note 3: Unless otherwise specified min/max limits apply across the 0˚C to +70˚C range for the DS96176. All typicals are given for VCC = 5V and TA = 25˚C. Note 4: All currents into the device pins are positive; all currents out of the device pins are negative. All voltages are referenced to ground unless otherwise specified. Note 5: ∆|VOD| and ∆|VOC| are the changes in magnitude of VOD and VOC, respectively, that occur when the input is changed from a high level to a low level. Note 6: In EIA Standards RS-422A and RS-485, VOC, which is the average of the two output voltages with respect to ground, is called output offset voltage, VOS. Note 7: The algebraic convention, where the less positive (more negative) limit is designated minimum, is used in this data sheet for common mode input voltage and threshold voltage levels only. 3 www.national.com DS96176 Not Recommended For New Designs Receiver Switching Characteristics (Continued) Note 8: Hysteresis is the difference between the positive-going input threshold voltage VT+, and the negative-going input threshold voltage, VT−. Note 9: Refer to EIA Standard RS-485 for exact conditions. Note 10: Only one output at a time should be shorted. Parameter Measurement Information DS009630-2 FIGURE 1. Driver VOD and VOC DS009630-3 FIGURE 2. Driver VOD with Varying Common Mode Voltage DS009630-4 FIGURE 3. Receiver VOH and VOL DS009630-5 DS009630-6 FIGURE 4. Driver Differential Output Delay and Transition Times DS009630-7 DS009630-8 FIGURE 5. Driver Propagation Times www.national.com 4 Parameter Measurement Information DS96176 Not Recommended For New Designs (Continued) DS009630-10 DS009630-9 FIGURE 6. Driver Enable and Disable Times (tPZH, tPHZ) DS009630-12 DS009630-11 FIGURE 7. Driver Enable and Disable Times (tPZL, tPLZ) DS009630-14 DS009630-13 FIGURE 8. Receiver Propagation Delay Times 5 www.national.com DS96176 Not Recommended For New Designs Parameter Measurement Information (Continued) DS009630-15 DS009630-17 DS009630-16 DS009630-19 DS009630-18 Note 11: The input pulse is supplied by a generator having the following characteristics: PRR = 1.0 MHz, 50% duty cycle, tr ≤ 6.0 ns, ZO = 50Ω. Note 12: CL includes probe and stray capacitance. Note 13: DS96176 Driver enable is Active-High. Note 14: All diodes are 1N916 or equivalent. FIGURE 9. Receiver Enable and Disable Times Typical Application DS009630-20 Note: The line length should be terminated at both ends of its characteristic impedance. Stub lengths off the main line should be kept as short as possible. FIGURE 10. www.national.com 6 DS96176 Not Recommended For New Designs Typical Performance Characteristics Driver Differential Propagation Delay vs VCC vs Temperature Driver Differential Propagation Delay vs VCC vs Temperature DS009630-22 Driver Differential Rise Time vs VCC vs Temperature DS009630-23 Driver Differential Fall Time vs VCC vs Temperature DS009630-24 DS009630-25 Driver Skew vs VCC vs Temperature (|tPLDH–tPHLD|) DS009630-26 7 www.national.com DS96176 Not Recommended For New Designs Typical Performance Characteristics (Continued) DS009630-27 FIGURE 11. Typical Curve Driver Propagation Delay Test Circuit DS009630-28 FIGURE 12. Typical Curve Driver Differential Propagation Delay Timing www.national.com 8 DS96176 Not Recommended For New Designs Typical Performance Curves DS009630-29 FIGURE 13. Typical Curve Driver Differential Rise and Fall Times Receiver Propagation Delay vs VCC vs Temperature Receiver Propagation Delay vs VCC vs Temperature DS009630-30 DS009630-31 Receiver Skew vs VCC vs Temperature (|tPLH–tPHL|) DS009630-32 DS009630-33 FIGURE 14. Typical Curve Receiver Differential Propagation Delay Test Circuit 9 www.national.com DS96176 Not Recommended For New Designs Typical Performance Curves (Continued) DS009630-34 FIGURE 15. Typical Curve Receiver Propagation Delay Timing www.national.com 10 Physical Dimensions DS96176 RS-485/RS-422 Differential Bus Transceiver Not Recommended For New Designs inches (millimeters) unless otherwise noted Molded Dual-In-Line Package (N) Order Number DS96176CN NS Package Number N08E LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated