14 Pin DIP 5 Tap Low Power TTL Compatible Active Delay Lines TAP DELAYS ±5% or 2 nS† TOTAL DELAYS ±5% or 2 nS† 10, 20, 30, 40 11, 22, 33, 44 12, 24, 36, 48 13, 26, 39, 52 14, 28, 42, 56 15, 30, 45, 60 16, 32, 48, 64 17, 34, 51, 68 18, 36, 54, 72 19, 38, 57, 76 20, 40, 60, 80 25, 50, 75, 100 †Whichever is greater. PART NUMBER 50 55 60 65 70 75 80 85 90 95 100 125 TAP DELAYS ±5% or 2 nS† EP8270 EP8271 EP8272 EP8273 EP8274 EP8275 EP8276 EP8277 EP8278 EP8279 EP8280 EP8281 30, 60, 90, 120 35, 70, 105, 140 40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 55, 110, 165, 220 60, 120, 180, 240 70, 140, 210, 280 80, 160, 240, 320 90, 180, 270, 360 100, 200, 300, 400 VOH VOL VIK IIH High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current IIL IOS Low-Level Input Current Short Circuit Output Current ICCH ICCL TRO NH NL High-Level Supply Current Low-Level Supply Current Output Rise Time Fanout High-Level Output Fanout Low-Level Output Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature 2.7 -5 V V V µA mA mA mA 0.5 -1.5 20 0.1 -0.36 -42 14 Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage 4 10 6 8 OUTPUT INPUT 1 7 GROUND 30 mA 30 mA 8 nS 20 TTL LOAD 20LS TTL LOAD Max Unit 4.75 2.0 5.25 V V V mA mA mA % % °C 0.8 -18 -0.4 8 40 0 40 +70 .200 PCA EP82XX Date Code White Dot Pin#1 .300 .280 Max. .100 .780 Max. Unit 3.2 110 2.0 1.0 100 5.0 Volts % nS MHz KHz Volts .020 Min. .250 Max. .010 Typ. .020 Typ. .125 ± .010 .365 Max. QAF-CSO1 Rev. B 8/25/94 Rev. A 2/5/96 Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010 12 VCC Package Dimensions Min Input Pulse Test Conditions DSD82XXb EP8282 EP8283 EP8284 EP8285 EP8286 EP8287 EP8288 EP8289 EP8290 EP8291 EP8292 Schematic *These two values are inter-dependent. VCC 150 175 200 225 250 275 300 350 400 450 500 Min Max Unit VCC = min. VIL = max. I OH = max VCC = min. VIH = min. IOL= max VCC = min. II = II K VCC = max. VIN = 2.7V VCC = max. VIN = 5.25V VCC = max. VIN = 0.5V VCC = max. VOUT = 0. (One output at a time) VCC = max. VIN = OPEN VCC = max. VIN = 0 Td ≤ 500 nS (0.75 to 2.4 Volts) VCC = max. VOH = 2.7V VCC = max. VOL = 0.5V Recommended Operating Conditions EIN PW TRI PRR PART NUMBER Delay times referenced from input to leading edges at 25°C, 5.0V, with no load. DC Electrical Characteristics Parameter Test Conditions VCC VIH VIL IIK IOH IOL PW* d* TA TOTAL DELAYS ±5% or 2 nS† ELECTRONICS INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791