TI1 LM723C Voltage regulator Datasheet

LM723, LM723C
www.ti.com
SNVS765C – JUNE 1999 – REVISED APRIL 2013
LM723/LM723C Voltage Regulator
Check for Samples: LM723, LM723C
FEATURES
DESCRIPTION
•
The LM723/LM723C is a voltage regulator designed
primarily for series regulator applications. By itself, it
will supply output currents up to 150 mA; but external
transistors can be added to provide any desired load
current. The circuit features extremely low standby
current drain, and provision is made for either linear
or foldback current limiting.
1
2
•
•
•
•
150 mA Output Current Without External Pass
Transistor
Output Currents in Excess of 10A Possible by
Adding External Transistors
Input Voltage 40V Max
Output Voltage Adjustable from 2V to 37V
Can be Used as Either a Linear or a Switching
Regulator
The LM723/LM723C is also useful in a wide range of
other applications such as a shunt regulator, a
current regulator or a temperature controller.
The LM723C is identical to the LM723 except that the
LM723C has its performance ensured over a 0°C to
+70°C temperature range, instead of −55°C to
+125°C.
Connection Diagram
Note: Pin 5 connected to case.
Figure 1. Top View
CDIP Package or PDIP Package
See Package J or NFF0014A
Figure 2. Top View
TO-100
See Package LME
Figure 3. Top View
See Package NAJ0020A
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1999–2013, Texas Instruments Incorporated
LM723, LM723C
SNVS765C – JUNE 1999 – REVISED APRIL 2013
www.ti.com
Equivalent Circuit*
*Pin numbers refer to metal can package.
Typical Application
for minimum temperature drift.
Typical Performance
Regulated Output Voltage
5V
Line Regulation (ΔVIN = 3V)
0.5mV
Load Regulation (ΔIL = 50 mA)
1.5mV
Figure 4. Basic Low Voltage Regulator (VOUT = 2 to 7 Volts)
2
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
LM723, LM723C
www.ti.com
SNVS765C – JUNE 1999 – REVISED APRIL 2013
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS (1) (2)
Pulse Voltage from V+ to V− (50 ms)
50V
Continuous Voltage from V+ to V−
40V
Input-Output Voltage Differential
40V
Maximum Amplifier Input Voltage
(Either Input)
8.5V
Maximum Amplifier Input Voltage
(Differential)
5V
Current from VZ
25 mA
Current from VREF
15 mA
Internal Power Dissipation
Metal Can (3)
800 mW
CDIP
(3)
900 mW
PDIP
(3)
660 mW
Operating Temperature Range
−55°C to +150°C
LM723
LM723C
0°C to +70°C
Storage Temperature Range
Metal Can
−65°C to +150°C
−55°C to +150°C
PDIP
Lead Temperature (Soldering, 4 sec. max.)
Hermetic Package
300°C
Plastic Package
260°C
ESD Tolerance
1200V
(Human body model, 1.5 kΩ in series with 100 pF)
(1)
(2)
(3)
“Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits.
A military RETS specification is available on request. At the time of printing, the LM723 RETS specification complied with the Min and
Max limits in this table. The LM723E, H, and J may also be procured as a Standard Military Drawing.
See derating curves for maximum power rating above 25°C.
ELECTRICAL CHARACTERISTICS (1) (2) (3) (4)
Parameter
Conditions
LM723
Min
Line Regulation
VIN = 12V to VIN = 15V
LM723C
Typ
Max
0.01
0.1
−55°C ≤ TA ≤ +125°C
Min
Max
0.01
0.1
0.3
(2)
(3)
(4)
% VOUT
0.02
0.2
0.1
0.5
% VOUT
IL = 1 mA to IL = 50 mA
0.03
0.15
0.03
0.2
% VOUT
0.6
% VOUT
0°C ≤ TA ≤ +70°C
(1)
0.3
VIN = 12V to VIN = 40V
−55°C ≤ TA ≤ +125°C
Ripple Rejection
% VOUT
% VOUT
0°C ≤ TA ≤ +70°C
Load Regulation
Units
Typ
0.6
% VOUT
f = 50 Hz to 10 kHz, CREF = 0
74
74
dB
f = 50 Hz to 10 kHz, CREF = 5 μF
86
86
dB
Unless otherwise specified, TA = 25°C, VIN = V+ = VC = 12V, V− = 0, VOUT = 5V, IL = 1 mA, RSC = 0, C1 = 100 pF, CREF = 0 and divider
impedance as seen by error amplifier ≤ 10 kΩ connected as shown in Figure 4. Line and load regulation specifications are given for the
condition of constant chip temperature. Temperature drifts must be taken into account separately for high dissipation conditions.
A military RETS specification is available on request. At the time of printing, the LM723 RETS specification complied with the Min and
Max limits in this table. The LM723E, H, and J may also be procured as a Standard Military Drawing.
Specified by correlation to other tests.
L1 is 40 turns of No. 20 enameled copper wire wound on Ferroxcube P36/22-3B7 pot core or equivalent with 0.009 in. air gap.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
3
LM723, LM723C
SNVS765C – JUNE 1999 – REVISED APRIL 2013
www.ti.com
ELECTRICAL CHARACTERISTICS(1)(2)(3)(4) (continued)
Parameter
Conditions
LM723
Min
Average Temperature Coefficient of
Output Voltage ( (5))
−55°C ≤ TA ≤ +125°C
LM723C
Typ
Max
0.002
0.015
Min
Reference Voltage
Output Noise Voltage
0.003
RSC = 10Ω, VOUT = 0
65
6.95
0.015
65
7.35
6.80
7.15
%/°C
mA
7.50
V
μVrms
BW = 100 Hz to 10 kHz, CREF = 0
86
86
BW = 100 Hz to 10 kHz, CREF = 5 μF
2.5
2.5
μVrms
0.05
0.05
%/1000
hrs
Long Term Stability
Standby Current Drain
7.15
Units
Max
%/°C
0°C ≤ TA ≤ +70°C
Short Circuit Current Limit
Typ
4.0
mA
Input Voltage Range
IL = 0, VIN = 30V
9.5
40
9.5
40
V
Output Voltage Range
2.0
37
2.0
37
V
3.0
38
3.0
Input-Output Voltage Differential
1.7
3.5
1.7
38
V
θJA
PDIP
θJA
CDIP
150
θJA
H10C Board Mount in Still Air
165
165
°C/W
θJA
H10C Board Mount in 400 LF/Min Air Flow
66
66
°C/W
22
22
°C/W
105
θJC
(5)
4
°C/W
°C/W
For metal can applications where VZ is required, an external 6.2V zener diode should be connected in series with VOUT.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
LM723, LM723C
www.ti.com
SNVS765C – JUNE 1999 – REVISED APRIL 2013
TYPICAL PERFORMANCE CHARACTERISTICS
Load Regulation
Characteristics with
Current Limiting
Load Regulation
Characteristics with
Current Limiting
Figure 5.
Figure 6.
Load & Line Regulation vs
Input-Output Voltage
Differential
Current Limiting
Characteristics
Figure 7.
Figure 8.
Current Limiting
Characteristics vs
Junction Temperature
Standby Current Drain vs
Input Voltage
Figure 9.
Figure 10.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
5
LM723, LM723C
SNVS765C – JUNE 1999 – REVISED APRIL 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Line Transient Response
Load Transient Response
Figure 11.
Figure 12.
Output Impedence vs
Frequency
Figure 13.
6
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
LM723, LM723C
www.ti.com
SNVS765C – JUNE 1999 – REVISED APRIL 2013
MAXIMUM POWER RATINGS
Noise
vs
Filter Capacitor
(CREF in Circuit of Figure 4)
(Bandwidth 100 Hz to 10 kHz)
LM723
Power Dissipation vs
Ambient Temperature
Figure 14.
Figure 15.
LM723C
Power Dissipation vs
Ambient Temperature
Figure 16.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
7
LM723, LM723C
SNVS765C – JUNE 1999 – REVISED APRIL 2013
www.ti.com
Table 1. Resistor Values (kΩ) for Standard Output Voltage
Positive
Output
Voltage
(1)
(2)
(3)
Applicable Figures
Fixed
Output ±5%
Output
Adjustable
±10% (1)
Negative
Output
Voltage
See (2)
R1
R2
R1
P1
R2
+3.0
Figure 4, Figure 19,
Figure 21, Figure 24,
Figure 27 (Figure 19)
4.12
3.01
1.8
0.5
1.2
+100
+3.6
Figure 4, Figure 19,
Figure 21, Figure 24,
Figure 27 (Figure 19)
3.57
3.65
1.5
0.5
1.5
+5.0
Figure 4, Figure 19,
Figure 21, Figure 24,
Figure 27 (Figure 19)
2.15
4.99
0.75
0.5
+6.0
Figure 4, Figure 19,
Figure 21, Figure 24,
Figure 27 (Figure 19)
1.15
6.04
0.5
+9.0
Figure 17, Figure 19,
(Figure 19, Figure 21,
Figure 24, Figure 27)
1.87
7.15
+12
Figure 17, Figure 19,
(Figure 19, Figure 21,
Figure 24, Figure 27)
4.87
+15
Figure 17, Figure 19,
(Figure 19, Figure 21,
Figure 24, Figure 27)
+28
Applicable
Figures
Fixed
Output ±5%
5% Output
Adjustable
±10%
R1
R2
R1
P1
R2
Figure 22
3.57
102
2.2
10
91
+250
Figure 22
3.57
255
2.2
10
240
2.2
−6 (3)
Figure 18,
(Figure 25)
3.57
2.43
1.2
0.5
0.75
0.5
2.7
−9
Figure 18,
Figure 25
3.48
5.36
1.2
0.5
2.0
0.75
1.0
2.7
−12
Figure 18,
Figure 25
3.57
8.45
1.2
0.5
3.3
7.15
2.0
1.0
3.0
−15
Figure 18,
Figure 25
3.65
11.5
1.2
0.5
4.3
7.87
7.15
3.3
1.0
3.0
−28
Figure 18,
Figure 25
3.57
24.3
1.2
0.5
10
Figure 17, Figure 19,
(Figure 19, Figure 21,
Figure 24, Figure 27)
21.0
7.15
5.6
1.0
2.0
−45
Figure 23
3.57
41.2
2.2
10
33
+45
Figure 22
3.57
48.7
2.2
10
39
−100
Figure 23
3.57
97.6
2.2
10
91
+75
Figure 22
3.57
78.7
2.2
10
68
−250
Figure 23
3.57
249
2.2
10
240
Replace R1/R2 in figures with divider shown in Figure 28.
Figures in parentheses may be used if R1/R2 divider is placed on opposite input of error amp.
V+ and VCC must be connected to a +3V or greater supply.
Table 2. Formulae for Intermediate Output Voltages
8
Outputs from +2 to +7 volts
Outputs from +4 to +250 volts
(Figure 4 Figure 19 Figure 20
Figure 21 Figure 24 Figure 27
(Figure 22)
Outputs from +7 to +37 volts
Outputs from −6 to −250 volts
(Figure 17 Figure 19 Figure 20
Figure 21 Figure 24 Figure 27)
(Figure 18 Figure 23 Figure 25)
Submit Documentation Feedback
Current Limiting
Foldback Current Limiting
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
LM723, LM723C
www.ti.com
SNVS765C – JUNE 1999 – REVISED APRIL 2013
TYPICAL APPLICATIONS
for minimum temperature drift.
R3 may be eliminated for minimum component count.
Typical Performance
Regulated Output Voltage
15V
Line Regulation (ΔVIN = 3V)
1.5 mV
Load Regulation (ΔIL = 50 mA)
4.5 mV
Figure 17. Basic High Voltage Regulator (VOUT = 7 to 37 Volts)
Typical Performance
Regulated Output Voltage
−15V
Line Regulation (ΔVIN = 3V)
1 mV
Load Regulation (ΔIL = 100 mA)
2 mV
Figure 18. Negative Voltage Regulator
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
9
LM723, LM723C
SNVS765C – JUNE 1999 – REVISED APRIL 2013
www.ti.com
Typical Performance
Regulated Output Voltage
+15V
Line Regulation (ΔVIN = 3V)
1.5 mV
Load Regulation (ΔIL = 1A)
15 mV
Figure 19. Positive Voltage Regulator (External NPN Pass Transistor)
Typical Performance
Regulated Output Voltage
+5V
Line Regulation (ΔVIN = 3V)
0.5 mV
Load Regulation (ΔIL = 1A)
5 mV
Figure 20. Positive Voltage Regulator (External PNP Pass Transistor)
10
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
LM723, LM723C
www.ti.com
SNVS765C – JUNE 1999 – REVISED APRIL 2013
Typical Performance
Regulated Output Voltage
+5V
Line Regulation (ΔVIN = 3V)
0.5 mV
Load Regulation (ΔIL = 10 mA)
1 mV
Short Circuit Current
20 mA
Figure 21. Foldback Current Limiting
Typical Performance
Regulated Output Voltage
+50V
Line Regulation (ΔVIN = 20V)
15 mV
Load Regulation (ΔIL = 50 mA)
20 mV
Figure 22. Positive Floating Regulator
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
11
LM723, LM723C
SNVS765C – JUNE 1999 – REVISED APRIL 2013
www.ti.com
Typical Performance
Regulated Output Voltage
−100V
Line Regulation (ΔVIN = 20V)
30 mV
Load Regulation (ΔIL = 100 mA)
20 mV
Figure 23. Negative Floating Regulator
Typical Performance
Regulated Output Voltage
+5V
Line Regulation (ΔVIN = 30V)
10 mV
Load Regulation (ΔIL = 2A)
80 mV
Figure 24. Positive Switching Regulator
12
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
LM723, LM723C
www.ti.com
SNVS765C – JUNE 1999 – REVISED APRIL 2013
Typical Performance
Regulated Output Voltage
−15V
Line Regulation (ΔVIN = 20V)
8 mV
Load Regulation (ΔIL = 2A)
6 mV
Figure 25. Negative Switching Regulator
Note: Current limit transistor may be used for shutdown if current limiting is not required.
Typical Performance
Regulated Output Voltage
+5V
Line Regulation (ΔVIN = 3V)
0.5 mV
Load Regulation (ΔIL = 50 mA)
1.5 mV
Figure 26. Remote Shutdown Regulator with Current Limiting
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
13
LM723, LM723C
SNVS765C – JUNE 1999 – REVISED APRIL 2013
www.ti.com
Regulated Output Voltage
+5V
Line Regulation (ΔVIN = 10V)
0.5 mV
Load Regulation (ΔIL = 100 mA)
1.5 mV
Figure 27. Shunt Regulator
Figure 28. Output Voltage Adjust
(1)
14
(1)
Replace R1/R2 in figures with divider shown in Figure 28.
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
LM723, LM723C
www.ti.com
SNVS765C – JUNE 1999 – REVISED APRIL 2013
Schematic Diagram
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
15
LM723, LM723C
SNVS765C – JUNE 1999 – REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision B (April 2013) to Revision C
•
16
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 15
Submit Documentation Feedback
Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM723 LM723C
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM723CH
ACTIVE
TO-100
LME
10
500
TBD
Call TI
Call TI
0 to 70
( LM723CH ~
LM723CH)
LM723CH/NOPB
ACTIVE
TO-100
LME
10
500
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
0 to 70
( LM723CH ~
LM723CH)
LM723CN/NOPB
ACTIVE
PDIP
NFF
14
25
Green (RoHS
& no Sb/Br)
CU SN
Level-1-NA-UNLIM
0 to 70
LM723CN
LM723H
ACTIVE
TO-100
LME
10
500
TBD
Call TI
Call TI
-55 to 150
( LM723H ~ LM723H)
LM723H/NOPB
ACTIVE
TO-100
LME
10
500
Green (RoHS
& no Sb/Br)
Call TI
Level-1-NA-UNLIM
-55 to 150
( LM723H ~ LM723H)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
27-Jul-2016
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MMBC006 – MARCH 2001
LME (O–MBCY–W10)
METAL CYLINDRICAL PACKAGE
ø
0.370 (9,40)
0.335 (8,51)
ø
0.335 (8,51)
0.305 (7,75)
0.040 (1,02)
0.010 (0,25)
0.185 (4,70)
0.165 (4,19)
0.040 (1,02)
0.010 (0,25)
0.500 (12,70) MIN
Seating
Plane
ø
ø
0.021 (0,53)
0.016 (0,41)
0.160 (4,06)
0.120 (3,05)
0.120 (3,05)
0.110 (2,79)
4
3
0.034 (0,86)
0.028 (0,71)
36°
5
2
6
1
10
7
9
8
0.230 (5,84)
0.045 (1,14)
0.029 (0,74)
4202488/A 03/01
NOTES: A.
B.
C.
D.
E.
All linear dimensions are in inches (millimeters).
This drawing is subject to change without notice.
Leads in true position within 0.010 (0,25) R @ MMC at seating plane.
Pin numbers shown for reference only. Numbers may not be marked on package.
Falls within JEDEC MO–006/TO-100.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
NFF0014A
N0014A
N14A (Rev G)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated