Simple Sequencers™ in 6-Lead SC70 ADM1085/ADM1086/ADM1087/ADM1088 FUNCTIONAL BLOCK DIAGRAMS FEATURES Provide programmable time delays between enable signals Can be cascaded with power modules for multiple supply sequencing Power supply monitoring from 0.6 V Output stages: High voltage (up to 22 V) open-drain output (ADM1085/ADM1087) Push-pull output (ADM1086/ADM1088) Capacitor-adjustable time delays High voltage (up to 22 V) Enable and VIN inputs Low power consumption (15 µA) Specified over –40°C to +125°C temperature range 6-lead SC70 package VCC ADM1085/ADM1086 VIN CAPACITOR ADJUSTABLE DELAY 0.6V GND CEXT ENOUT ENIN VCC ADM1087/ADM1088 VIN CAPACITOR ADJUSTABLE DELAY 0.6V ENOUT Desktop/notebook computers, servers Low power portable equipment Routers Base stations Line cards Graphics cards GND CEXT 04591-PrG-001 APPLICATIONS ENIN Figure 1. GENERAL DESCRIPTION The ADM1085/ADM1086/ADM1087/ADM1088 are simple sequencing circuits that provide a time delay between the enabling of voltage regulators and/or dc-dc converters at powerup in multiple supply systems. When the output voltage of the first power module reaches a preset threshold, a time delay is initiated before an enable signal allows subsequent regulators to power up. Any number of these devices can be cascaded with regulators to allow sequencing of multiple power supplies. Threshold levels can be set with a pair of external resistors in a voltage divider configuration. By choosing appropriate resistor values, the threshold can be adjusted to monitor voltages as low as 0.6 V. The ADM1086 and ADM1088 have push-pull output stages, with active-high (ENOUT) and active-low (ENOUT) logic outputs, respectively. The ADM1085 has an active-high (ENOUT) logic output; the ADM1087 has an active-low (ENOUT) output. Both the ADM1085 and ADM1087 have open-drain output stages that can be pulled up to voltage levels as high as 22 V through an external resistor. This level-shifting property ensures compatibility with enable input logic levels of different regulators and converters. All four models have a dedicated enable input pin that allows the output signal to the regulator to be controlled externally. This is an active-high input (ENIN) for the ADM1085 and ADM1086, and an active-low input (ENIN) for the ADM1087 and ADM1088. The simple sequencers are specified over the extended −40°C to +125°C temperature range. With low current consumption of 15 µA (typ) and 6-lead SC70 packaging, the parts are suitable for low-power portable applications. Table 1. Selection Table Output Stage Part No. ADM1085 ADM1086 ADM1087 ADM1088 Enable Input ENIN ENIN ENIN ENIN ENOUT ENOUT Open-Drain Push-Pull Open-Drain Push-Pull Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.326.8703 © 2004 Analog Devices, Inc. All rights reserved. ADM1085/ADM1086/ADM1087/ADM1088 TABLE OF CONTENTS Specifications..................................................................................... 3 Application Information................................................................ 11 Absolute Maximum Ratings............................................................ 4 Sequencing Circuits ................................................................... 11 ESD Caution.................................................................................. 4 Dual LOFO Sequencing ............................................................ 13 Pin Configuration and Function Descriptions............................. 5 Simultaneous Enabling.............................................................. 13 Typical Performance Characteristics ............................................. 6 Power Good Signal Delays........................................................ 13 Circuit Information .......................................................................... 9 Quad-Supply Power Good Indicator....................................... 14 Timing Characteristics and Truth Tables.................................. 9 Sequencing with FET Switches................................................. 14 Capacitor-Adjustable Delay Circuit........................................... 9 Outline Dimensions ....................................................................... 15 Open-Drain and Push-Pull Outputs ....................................... 10 Ordering Guide .......................................................................... 15 REVISION HISTORY 7/04—Revision 0: Initial Version Rev. 0 | Page 2 of 16 ADM1085/ADM1086/ADM1087/ADM1088 SPECIFICATIONS VCC = full operating range, TA = −40°C to +125°C, unless otherwise noted. Table 2. Parameter SUPPLY VCC Operating Voltage Range VIN Operating Voltage Range Supply Current VIN Rising Threshold, VTH_RISING VIN Falling Threshold, VTH_FALLING VIN Hysteresis VIN to ENOUT/ENOUT Delay VIN Rising Min 2.25 0 0.56 0.545 ENOUT/ENOUT Voltage High (ADM1086/ADM1088) ENOUT/ENOUT Open-Drain Output Leakage Current (ADM1085/ADM1087) 10 0.6 0.585 15 Max Unit 3.6 22 15 0.64 0.625 V V µA V V mV 35 2 20 VIN Falling VIN Leakage Current CEXT Charge Current Threshold Temperature Coefficient ENIN/ENIN TO ENOUT/ENOUT Propagation Delay ENIN/ENIN Voltage Low ENIN/ENIN Voltage High ENIN/ENIN Leakage Current ENOUT/ENOUT Voltage Low Typ 125 170 250 30 0.5 µs ms µs 375 0.3 VCC − 0.2 0.3 VCC + 0.2 170 0.4 µA nA ppm/°C µs V V µA V V 0.8 VCC 0.4 Rev. 0 | Page 3 of 16 µA Test Conditions/Comments VCC = 3.3 V VCC = 3.3 V CEXT floating, C = 20 pF CEXT = 470 pF VIN = VTH_FALLING to (VTH_FALLING – 100 mV) VIN = 22 V VIN > VTH_RISING ENIN/ENIN = 22 V VIN < VTH_FALLING (ENOUT), VIN > VTH_RISING (ENOUT), ISINK = 1.2 mA VIN > VTH_RISING (ENOUT), VIN < VTH_FALLING (ENOUT), ISOURCE = 500 µA ENOUT/ENOUT = 22 V ADM1085/ADM1086/ADM1087/ADM1088 ABSOLUTE MAXIMUM RATINGS Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. TA = 25°C, unless otherwise noted. Table 3. Parameter VCC VIN CEXT ENIN, ENIN ENOUT, ENOUT (ADM1085, ADM1087) ENOUT, ENOUT (ADM1086, ADM1088) Rating −0.3 V to +6 V −0.3 V to +25 V Operating Temperature Range Storage Temperature Range θJA Thermal Impedance, SC70 Lead Temperature Soldering (10 s) Vapor Phase (60 s) Infrared (15 s) −40°C to +125°C −65°C to +150°C 146°C/W −0.3 V to +6 V −0.3 V to +25 V −0.3 V to +25 V −0.3 V to +6 V 300°C 215°C 220°C ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. 0 | Page 4 of 16 ADM1085/ADM1086/ADM1087/ADM1088 ENIN/ENIN 1 GND 2 VIN 3 ADM1085/ ADM1086/ ADM1087/ ADM1088 6 VCC 5 CEXT 4 ENOUT/ENOUT TOP VIEW (Not to Scale) 04591-PrG-002 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS Figure 2. Pin Configuration Table 4. Pin Function Descriptions Pin No. 1 Mnemonic ENIN, ENIN 2 3 GND VIN 4 ENOUT, ENOUT 5 CEXT 6 VCC Description Enable Input. Controls the status of the enable output. Active high for ADM1085/ADM1086. Active low for ADM1087/ADM1088. Ground. Input for the Monitored Voltage Signal. Can be biased via a voltage divider resistor network to customize the effective input threshold. Can precisely monitor an analog power supply output signal and detect when it has powered up. The voltage applied at this pin is compared with a 0.6 V on-chip reference. With this reference, digital signals with various logic-level thresholds can also be detected. Enable Output. Asserted when the voltage at VIN is above VTH_RISING and the time delay has elapsed, provided that the enable input is asserted. Active high for the ADM1085/ADM1086. Active low for the ADM1087/ADM1088. External Capacitor Pin. The capacitance on this pin determines the time delay on the enable output. The delay is seen only when the voltage at VIN rises past VTH_RISING, and not when it falls below VTH_FALLING. Power Supply. Rev. 0 | Page 5 of 16 ADM1085/ADM1086/ADM1087/ADM1088 TYPICAL PERFORMANCE CHARACTERISTICS 200 680 180 660 160 640 620 600 580 560 VTRIP FALLING 04591-PrG-003 540 520 500 –40 –25 –10 5 20 35 50 65 TEMPERATURE (°C) 80 95 110 140 TA = +25°C 120 100 80 TA = –40°C 60 40 20 0 125 0 Figure 3. VIN Threshold vs. Temperature 4 6 8 10 12 VIN (V) 16 18 20 22 200 190 11.5 TA = +25°C VIN LEAKAGE CURRENT (µA) 11.0 10.5 10.0 TA = +125°C TA = –40°C 9.5 04591-PrG-004 9.0 8.5 8.0 2.10 2.40 2.70 3.00 3.30 TA = +125°C 180 170 160 TA = +25°C 150 140 TA = –40°C 130 120 110 100 2.10 3.60 VCC (V) 2.40 2.70 3.00 3.30 3.60 VCC (V) Figure 4. Supply Current vs. Supply Voltage Figure 7. VIN Leakage Current vs. VCC Voltage 20 10000 TA = +125°C 18 16 1000 12 10 8 6 4 2 0 0 2 4 6 8 10 12 VIN (V) 14 16 18 20 TA = +25°C 100 TA = –40°C 10 1 0.1 0.01 22 Figure 5. Supply Current vs. VIN Voltage 04591-PrG-008 OUTPUT VOLTAGE (mV) 14 04591-PrG-005 SUPPLY CURRENT (µA) 14 Figure 6. VIN Leakage Current vs. VIN Voltage 12.0 ICC (µA) 2 04591-PrG-007 VTRIP (mV) VTRIP RISING TA = +125°C 04591-PrG-006 VIN LEAKAGE CURRENT (µA) 700 0.1 1 10 OUTPUT SINK CURRENT (mA) 20 Figure 8. Output Voltage vs. Output Sink Current Rev. 0 | Page 6 of 16 100 ADM1085/ADM1086/ADM1087/ADM1088 200 120 180 ENIN/ENIN LEAKAGE (µA) 80 60 40 0 2.10 2.40 2.70 3.00 SUPPLY VOLTAGE (V) 3.30 120 100 TA = –40°C 80 60 20 0 3.60 0 Figure 9. Output Low Voltage vs. Supply Voltage 100 200 90 180 80 160 70 140 4 6 8 10 12 14 ENIN/ENIN (V) 16 18 20 22 ENIN LEAKAGE (µA) TA = +125°C 1mV/µs 50 40 10mV/µs 30 20 10 –25 –10 5 20 35 50 65 TEMPERATURE (°C) 80 95 110 TA = +25°C TA = –40°C 120 100 80 60 40 04591-PrG-013 60 0 –40 2 Figure 12. ENIN/ENIN Leakage Current vs. ENIN/ENIN Voltage 04591-PrG-010 PROPAGATION DELAY (µs) 140 04591-PrG-012 20 TA = +25°C 40 04591-PrG-009 OUTPUT LOW VOLTAGE (mV) TA = +125°C 160 100 20 0 2.10 125 2.40 2.70 3.00 3.30 3.60 VCC (V) Figure 10. VCC Falling Propagation Delay vs. Temperature Figure 13. ENIN/ENIN Leakage Current vs. VCC Voltage 10000 500 450 1000 400 CEXT (nF) 300 250 200 100 10 150 50 0 2.10 1 2.40 2.70 3.00 SUPPLY VOLTAGE (V) 3.30 0.1 0.562 2.390 3.60 Figure 11. Output Fall Time vs. Supply Voltage 04591-PrG-014 100 04591-PrG-011 FALL TIME (ns) 350 5.02 22.9 53.2 241 520 TIMEOUT DELAY (ms) 2350 4480 26200 Figure 14. CEXT Capacitance vs. Timeout Delay Rev. 0 | Page 7 of 16 300 100 280 90 260 80 240 220 200 180 160 04591-PrG-015 140 120 100 –40 –25 –10 5 20 35 50 65 TEMPERATURE (°C) 80 95 110 90 70 60 50 40 30 04591-PrG-016 PROPAGATION DELAY (µs) 80 0 –40 –25 –10 5 20 35 50 65 TEMPERATURE (°C) 80 95 110 50 40 30 20 10 0 10 100 COMPARATOR OVERDRIVE (mV) 1000 Figure 17. Maximum VIN Transient Duration vs. Comparator Overdrive 100 10 60 1 125 Figure 15. CEXT Charge Current vs. Temperature 20 70 04591-PrG-017 TRANSIENT DURATION (µs) CHARGE CURRENT (nA) ADM1085/ADM1086/ADM1087/ADM1088 125 Figure 16. VIN to ENOUT/ENOUT Propagation Delay (CEXT Floating) vs. Temperature Rev. 0 | Page 8 of 16 ADM1085/ADM1086/ADM1087/ADM1088 CIRCUIT INFORMATION TIMING CHARACTERISTICS AND TRUTH TABLES When VIN reaches the upper threshold voltage (VTH_RISING), an internal circuit generates a delay (tEN) before the enable output is asserted. If VIN drops below the lower threshold voltage (VTH_FALLING), the enable output is deasserted immediately. The enable outputs of the ADM1085/ADM1086/ADM1087/ ADM1088 are related to the VIN and enable inputs by a simple AND function. The enable output is asserted only if the enable input is asserted and the voltage at VIN is above VTH_RISING, with the time delay elapsed. Table 5 and Table 6 show the enable output logic states for different VIN/enable input combinations when the capacitor delay has elapsed. The timing diagrams in Figure 18 and Figure 19 give a graphical representation of how the ADM1085/ADM1086/ADM1087/ADM1088 enable outputs respond to VIN and enable input signals. Similarly, if the enable input is disabled while VIN is above the threshold, the enable output deasserts immediately. Unlike VIN, a low-to-high transition on ENIN (or high-to-low on ENIN) does not yield a time delay on ENOUT (ENOUT). CAPACITOR-ADJUSTABLE DELAY CIRCUIT Figure 20 shows the internal circuitry used to generate the time delay on the enable output. A 250 nA current source charges a small internal parasitic capacitance, CINT. When the capacitor voltage reaches 1.2 V, the enable output is asserted. The time taken for the capacitor to reach 1.2 V, in addition to the propagation delay of the comparator, constitutes the enable timeout, which is typically 35 µs. Table 5. ADM1085/ADM1086 Truth Table ENIN 0 1 0 1 ENOUT 0 0 0 1 To minimize the delay between VIN falling below VTH_FALLING and the enable output de-asserting, an NMOS transistor is connected in parallel with CINT. The output of the voltage detector is connected to the gate of this transistor so that, when VIN falls below VTH_FALLING, the transistor switches on and CINT discharges quickly. Table 6. ADM1087/ADM1088 Truth Table VIN <VTH_FALLING <VTH_FALLING >VTH_RISING >VTH_RISING ENIN ENOUT 1 0 1 0 1 1 1 0 VCC 250nA SIGNAL FROM VOLTAGE DETECTOR VIN VTH_RISING VTH_FALLING CINT 1.2V TO AND GATE AND OUTPUT STAGE CEXT C ENOUT tEN 04591-PrG-023 ENIN Figure 18. ADM1085/ADM1086 Timing Diagram VIN VTH_RISING Figure 20. Capacitor-Adjustable Delay Circuit Connecting an external capacitor to the CEXT pin delays the rise time—and therefore the enable timeout—further. The relationship between the value of the external capacitor and the resulting timeout is characterized by the following equation: VTH_FALLING tEN 04591-PrG-024 ENIN ENOUT 04591-PrG-024 VIN <VTH_FALLING <VTH_FALLING >VTH_RISING >VTH_RISING Figure 19. ADM1087/ADM1088 Timing Diagram Rev. 0 | Page 9 of 16 tEN = (C × 4.8 ×106) + 35 µs ADM1085/ADM1086/ADM1087/ADM1088 OPEN-DRAIN AND PUSH-PULL OUTPUTS The ADM1085 and ADM1087 have open-drain output stages that require an external pull-up resistor to provide a logic-high voltage level. The geometry of the NMOS transistor enables the output to be pulled up to voltage levels as high as 22 V. The ADM1086 and ADM1088 have push-pull (CMOS) output stages that require no external components to drive other logic circuits. An internal PMOS pull-up transistor provides the logic-high voltage level. VCC (≤22V) ADM1086/ADM1088 ADM1085/ADM1087 VCC LOGIC Figure 21. Open-Drain Output Stage Figure 22. Push-Pull Output Stage Rev. 0 | Page 10 of 16 04591-PrG-027 04591-PrG-026 LOGIC ADM1085/ADM1086/ADM1087/ADM1088 APPLICATION INFORMATION SEQUENCING CIRCUITS In Figure 23, three ADM1085s are used to sequence four supplies on power-up. Separate capacitors on the CEXT pins determine the time delays between enabling of the 3.3 V, 2.5 V, 1.8 V, and 1.2 V supplies. Because the dc/dc converters and ADM1085s are connected in cascade, and the output of any converter is dependent on that of the previous one, an external controller can disable all four supplies simultaneously by disabling the first dc/dc converter in the chain. The ADM1085/ADM1086/ADM1087/ADM1088 are compatible with voltage regulators and dc-to-dc converters that have active-high or active-low enable or shutdown inputs, with a choice of open-drain or push-pull output stages. Figure 23 to Figure 25 illustrate how each of the ADM1085/ADM1086/ ADM1087/ADM1088 simple sequencers can be used in multiple-supply systems, depending on which regulators are used and which output stage is preferred. For power-down sequencing, an external controller dictates when the supplies are switched off by accessing the ENIN inputs individually. 12V 3.3V DC/DC OUT 3.3V EN 3.3V IN DC/DC OUT ENABLE CONTROL OUT ENIN IN DC/DC OUT 1.2V 3.3V VCC VIN ENOUT ADM1085 CEXT EN 1.8V VCC VIN ENOUT ADM1085 ENIN DC/DC 3.3V VCC VIN EN 2.5V 3.3V 3.3V IN ENOUT ADM1085 CEXT ENIN CEXT 12V 3.3V 2.5V 1.8V 1.2V tEN1 tEN2 tEN3 EXTERNAL DISABLE Figure 23. Typical ADM1085 Application Circuit Rev. 0 | Page 11 of 16 04591-PrG-028 EN IN ADM1085/ADM1086/ADM1087/ADM1088 12V EN IN DC/DC OUT EN 3.3V IN DC/DC OUT 3.3V OUT ADM1086 ENIN IN DC/DC OUT 1.2V 3.3V VCC VIN ENOUT ADM1086 CEXT EN 1.8V VCC VIN ENOUT ENIN IN DC/DC 3.3V VCC VIN EN 2.5V ENOUT ADM1086 CEXT ENIN CEXT ENABLE CONTROL 12V 3.3V 2.5V 1.8V tEN1 tEN2 tEN3 04591-PrG-029 1.2V EXTERNAL DISABLE Figure 24. Typical ADM1086 Application Circuit 12V 12V OUT SD 3.3V IN ADP3334 OUT 2.5V SD IN ADP3334 OUT 3.3V OUT 2.5V VCC VIN ENOUT ADM1087 ENIN IN ADP3334 3.3V VCC VIN SD 3.3V CEXT ENOUT ADM1088 Figure 25. Typical ADM1087 Application Circuit Using ADP3334 Voltage Regulators ENIN CEXT Figure 26. Typical ADM1088 Application Circuit Using ADP3334 Voltage Regulators Rev. 0 | Page 12 of 16 04591-PrG-031 IN ADP3334 04591-PrG-030 SD ADM1085/ADM1086/ADM1087/ADM1088 DUAL LOFO SEQUENCING SIMULTANEOUS ENABLING A power sequencing solution for a portable device, such as a PDA, is shown in Figure 27. This solution requires that the microprocessor’s power supply turn on before the LCD display turns on, and that the LCD display power-down before the microprocessor powers down. In other words, the last power supply to turn on is the first one to turn off (LOFO). The enable output can drive multiple enable or shutdown regulator inputs simultaneously. For the display power sequencing, the ADM1085 is equipped with capacitor C2, which creates the delay between the microprocessor and display power turning on. When the system is powered down, the ADM1085 turns off the display power immediately, while the 3.3 V regulator waits for C1 to discharge to 0.4 V before switching off. 9V SYSTEM POWER SWITCH SD ADP3333 2.5V MICROPROCESSOR POWER 3.3V SD IN ADP3333 OUT SD 3.3V IN ADP3333 OUT 2.5V 3.3V VCC VIN ENOUT 12V ADM1085 ENIN CEXT SD IN ADP3333 OUT 1.8V ENABLE CONTROL Figure 28. Enabling a Pair of Regulators from a Single ADM1085 POWER GOOD SIGNAL DELAYS Sometimes sequencing is performed by asserting Power Good signals when the voltage regulators are already on, rather than sequencing the power supplies directly. In these scenarios, a simple sequencer IC can provide variable delays so that enabling separate circuit blocks can be staggered in time. For example, in a notebook PC application, a dedicated microcomputer asserts a Power Good signal for North Bridge™ and South Bridge™ ICs. The ADM1086 delays the south bridge’s signal, so that it is enabled after the north bridge. C1 9V 5V 3.3V 5V 9V POWER_GOOD EN MICROCOMPUTER ENOUT SD ADP3333 5V NORTH BRIDGE IC DISPLAY POWER ADM1086 ENIN CEXT 3.3V C2 VIN SYSTEM POWER 9V 5V ENOUT EN ADM1086 ENIN 0V 9V CEXT VC1 0V Figure 29. Power Good Delay 2.5V 0V 5V DISPLAY POWER 0V 04591-PrG-032 MICROPROCESSOR POWER Figure 27. Dual LOFO Power-Supply Sequencing Rev. 0 | Page 13 of 16 SOUTH BRIDGE IC 04591-PrG-034 VIN 04591-PrG-033 An RC network connects the battery and the SD input of the ADP3333 voltage regulator. This causes power-up and powerdown transients to appear at the SD input when the battery is connected and disconnected. The 3.3 V microprocessor supply turns on quickly on power-up and turns off slowly on powerdown. This is due to two factors: Capacitor C1 charges up to 9 V on power-up and charges down from 9 V on power-down, and the SD pin has logic-high and logic-low input levels of 2 V and 0.4 V. 12V ADM1085/ADM1086/ADM1087/ADM1088 QUAD-SUPPLY POWER GOOD INDICATOR SEQUENCING WITH FET SWITCHES The enable output of the simple sequencers is equivalent to an AND function of VIN and ENIN. ENOUT is high only when the voltage at VIN is above the threshold and the enable input (ENIN) is high as well. Although ENIN is a digital input, it can tolerate voltages as high as 22 V and can detect if a supply is present. Therefore, a simple sequencer can monitor two supplies and assert what can be interpreted as a Power Good signal when both supplies are present. The outputs of two ADM1085s can be wire-ANDed together to make a quad-supply Power Good indicator. The open-drain outputs of the ADM1085 and ADM1087 can drive external FET transistors, which can switch on powersupply rails. All that is needed is a pull-up resistor to a voltage source that is high enough to turn on the FET. 12V 3.3V VIN ADM1085 3.3V 3.3V VIN ENOUT ENIN POWER_GOOD ADM1085 5V 2.5V Figure 31. Sequencing with a FET Switch ENIN 3.3V 2.5V VIN ENOUT ENIN 04591-PrG-035 ADM1085 1.8V CEXT 04591-PrG-036 9V ENOUT Figure 30. Quad-Supply Power Good Indicator Rev. 0 | Page 14 of 16 ADM1085/ADM1086/ADM1087/ADM1088 OUTLINE DIMENSIONS 2.00 BSC 6 5 4 1 2 3 2.10 BSC 1.25 BSC PIN 1 0.65 BSC 1.30 BSC 1.00 0.90 0.70 1.10 MAX 0.22 0.08 0.30 0.15 0.10 MAX SEATING PLANE 8° 4° 0° 0.46 0.36 0.26 0.10 COPLANARITY COMPLIANT TO JEDEC STANDARDS MO-203AB Figure 32. 6-Lead Plastic Surface-Mount Package [SC70] (KS-6) Dimensions shown in millimeters ORDERING GUIDE Model ADM1085AKS-REEL7 Temperature Range −40°C to +125°C Quantity 3k ADM1086AKS-REEL7 −40°C to +125°C 3k ADM1087AKS-REEL7 −40°C to +125°C 3k ADM1088AKS-REEL7 −40°C to +125°C 3k Package Description 6-Lead Thin Shrink Small Outline Transistor Package (SC70) 6-Lead Thin Shrink Small Outline Transistor Package (SC70) 6-Lead Thin Shrink Small Outline Transistor Package (SC70) 6-Lead Thin Shrink Small Outline Transistor Package (SC70) Rev. 0 | Page 15 of 16 Package Option KS-6 Branding M0V KS-6 M0W KS-6 M0X KS-6 M0Y ADM1085/ADM1086/ADM1087/ADM1088 NOTES © 2004 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04591–0–7/04(0) Rev. 0 | Page 16 of 16