NEW PRODUCT NEW PRODUCT NEW PRODUCT G5SBA20 AND G5SBA60 GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 200 and 600 Volts Forward Current - 6.0 Amperes FEATURES Case Style GBU 0.140 (3.56) 0.130 (3.30) 0.880 (22.3) 0.860 (21.8) 0.020 R (TYP.) 0.125 (3.2) x 45o 9o TYP. CHAMFER 0.160 (4.1) 0.140 (3.5) 0.310 (7.9) 0.290 (7.4) 0.740 (18.8) 0.720 (18.3) 0.075 (1.9) R. 0.085 (2.16) 0.065 (1.65) 0.080 (2.03) 0.060 (1.52) 5o TYP. 0.085 (2.16) 0.075 (1.90) 0.710 (18.0) 0.690 (17.5) 0.100 (2.54) 0.085 (2.16) 0.050 (1.27) 0.040 (1.02) ¨ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ¨ This series is UL listed under the Recognized Component Index, file number E54214 ¨ High case dielectric strength of 1500 VRMS ¨ Ideal for printed circuit boards ¨ Glass passivated chip junction ¨ High surge current capability ¨ High temperature soldering guaranteed: 260¡C/10 seconds, 0.375 (9.5mm) lead length, 5lbs. (2.3kg) tension MECHANICAL DATA 0.022 (0.56) 0.080 (2.03) 0.065 (1.65) Polarity 0.190 (4.83) 0.210 (5.33) 0.018 (0.46) Polarity front side of case, positive positive leadlead by beveled corner corner. shown onshown frontonside of case, beveled If preferred, marking may be on reverse side of case. Lead forming option with 10mm-7.5mm-7.5mm spacing is available. Dimensions in inches and (millimeters) Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Mounting Position: Any (NOTE 3) Mounting Torque: 5 in. - lb. max. Weight: 0.15 ounce, 4.0 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25¡C ambient temperature unless otherwise specified. SYMBOLS G5SBA20 G5SBA60 UNITS Maximum repetitive peak reverse voltage VRRM 200 600 Volts Maximum RMS voltage VRMS 140 420 Volts VDC 200 600 Volts Maximum DC blocking voltage Maximum average forward rectified TC=100¡C (NOTE 1) output current at TA=25¡C (NOTE 2) I(AV) 6.0 2.8 Amps Peak forward surge current single sine-wave superimposed on rated load (JEDEC Method) IFSM 150 Amps Rating for fusing (t<8.3ms) I2t 60 A2sec Maximum instantaneous forward voltage drop per leg at 3.0A VF 1.05 Volts Maximum DC reverse current at rated DC blocking voltage per leg IR 5.0 500 mA RQJA RQJC 22 3.4 ¡C/W TJ, TSTG -55 to +150 ¡C Typical thermal resistance per leg TA=25¡C TA=125¡C (NOTE 2) (NOTE 1) Operating junction and storage temperature range NOTES: (1) Unit case mounted on Al plate heatsink. (2) Units mounted on P.C.B. with 0.5 x 0.5" (12 x 12mm) copper pads and 0.375" (9.5mm) lead length (3) Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw 2/24/99 FIG. 1 - DERATING CURVE OUTPUT RECTIFIED CURRENT 8.0 HEATSINK MOUNTING, TC 6.0 4.0 2.0 P.C.B. MOUNTING, TA 0 150 100 50 0 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES RATINGS AND CHARACTERISTICS CURVES G5SBA20 THRU G5SBA60 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 150 TJ=TJ max. SINGLE SINE-WAVE (JEDEC Method) 100 50 1.0 CYCLE 0 NUMBER OF CYCLES AT 60 Hz TEMPERATURE, ¡C FIG. 3 - TYPICAL FORWARD CHARACTERISTICS PER LEG INSTANTANEOUS REVERSE CURRENT, MICROAMPERES FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT, AMPERES 100 10 TJ=25¡C PULSE WIDTH=300ms 1% DUTY CYCLE 1 0.1 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 500 100 TJ=125¡C 10 1 0.1 TJ=25¡C 0.01 0 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 100 REVERSE VOLTAGE, VOLTS 100 TRANSIENT THERMAL IMPEDANCE, ¡C/W JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHZ Vsig=50mVp-p 10 80 60 100 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE 1,000 1 40 20 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS 10 0.1 100 10 1 100 10 1 0.1 0.01 0.1 1 t, HEATING TIME, sec. 10 100