QT HLMP-6405A Subminiature t-3/4 led diffused and clear lamp Datasheet

SUBMINIATURE T-3/4 LED
DIFFUSED and CLEAR LAMPS
HIGH EFF. RED
YELLOW
GREEN
AIGaAs RED
HLMP-6305A
HLMP-6405A
HLMP-6505A
HLMP-Q105A
Water
Water
Water
Water
Clear
Clear
Clear
Clear
MV6700A
MV6300A
MV6400A
HLMP-Q150A
PACKAGE DIMENSIONS
.276 (7.0) MIN
.087 (2.2)
.079 (2.0)
DESCRIPTION
The QT Optoelectronics family of T-3/4 subminiature LED lamps feature a square-base, transfer
molded package for surface mount applications.
A tinted diffused or water clear epoxy lens —
available in AIGaAs red, high-efficiency red,
green, and yellow — produces wide-angle beam
emission and sharp on/off contrast. The LEDs are
offered with gullwing lead bends for top mounting,
as well as yoke lead bends and Z-bends for
mounting to the back of a PCB.
.276 (7.0) MIN
.020 (.5)
.012 (.3)
.024 (.6)
.016 (.4)
.091 (2.3)
.083 (2.1)
.075 (1.9) DIA
.063 (1.6)
Diffused
Diffused
Diffused
Diffused
.058 (1.48)
.050 (1.28)
FEATURES
.031 (.78)
.023 (.58)
■
■
■
CATHODE MARK
NOTE:
.010 (.26)
.002 (.06)
■
.056 (1.44)
.048 (1.24)
■
Subminiature T-3/4 transfer molded
Low package profile
Axial leads
Wide viewing angle
SMT versions
CATHODE MARK
1. ALL DIMENSIONS ARE IN INCHES (mm)
PHYSICAL CHARACTERISTICS
TYPE
SOURCE COLOR
LENS COLOR
HLMP-6305A
High Efficiency Red
Water Clear
HLMP-6405A
Yellow
Water Clear
HLMP-6505A
Green
Water Clear
HLMP-Q105A
AIGaAs Red
Water Clear
MV6700A
High Efficiency Red
Red Diffused
MV6300A
Yellow
Yellow Diffused
MV6400A
Green
Green Diffused
AIGaAs Red
Red Diffused
HLMP-Q150A
SUBMINIATURE T-3/4 LED
DIFFUSED and CLEAR LAMPS
ABSOLUTE MAXIMUM RATING (TA = 25° C Unless otherwise specified)
PARAMETER
HLMP-6305A
MV6700A
HLMP-6405A
MV6300A
HLMP-6505A
MV6400A
HLMP-Q105A
HLMP-Q150A
UNITS
Power dissipation
135
85
135
85
mW
Average forward current
30
20
30
30
mA
Peak forward current
(1mS pulsewidth, 0.1% DF)
90
60
90
300
mA
Lead soldering time at 260° C
3
3
3
3
sec
Operating temperature
-55 to 100
-55 to 100
-55 to 100
-20 to 100
°C
Storage temperature
-55 to 100
-55 to 100
-55 to 100
-55 to 100
°C
ELECTRO-OPTICAL CHARACTERISTICS (TA = 25° C Unless otherwise specified)
PART NUMBER QTLP-
MV6700A
MV6300A
MV6400A
HLMPQ150A
Luminous intensity (mcd)
TEST
CONDITIONS
IF = 10 mA
minimum
1.0
1.0
1.0
1.0*
typical
3.0
3.0
3.0
1.8*
Forward voltage (V)
IF = 10 mA
minimum
1.5
1.5
1.5
typical
1.8
2.0
2.0
1.6*
maximum
3.0
3.0
3.0
1.8*
Peak wavelength (nm)
635
583
570
660
Spectral line half width (nm)
40
36
28
20
Reverse voltage (V)
5
5
5
5
Viewing angle (°)
50
50
28
50
*Tested at
IF = 1 mA
IR =100 mA
ELECTRO-OPTICAL CHARACTERISTICS (TA = 25° C Unless otherwise specified)
PART NUMBER QTLP-
HLMP6305A
HLMP6405A
HLMP6505A
HLMPQ105A
Luminous intensity (mcd)
minimum
typical
TEST
CONDITIONS
IF = 10 mA
3.0
3.0
3.0
20.0*
12.0
12.0
12.0
50.0*
Forward voltage (V)
IF = 10 mA
minimum
1.5
1.5
1.5
typical
1.8
2.0
2.0
1.8*
maximum
3.0
3.0
3.0
2.4*
Peak wavelength (nm)
635
583
570
660
Spectral line half width (nm)
40
36
28
20
Reverse voltage (V)
5
5
5
5
Viewing angle (°)
25
25
25
25
*Tested at
IF = 20 mA
IR =100 mA
SUBMINIATURE T-3/4 LED
DIFFUSED and CLEAR LAMPS
TYPICAL ELECTRO-OPTICAL CHARACTERISTIC CURVES (TA = 25° C)
AIGaAs
RED
40
90
80
H-E RED
YELLOW
70
GREEN
60
50
40
30
LUMINOUS INTENSITY
PEAK FORWARD CURRENT IF (mA)
100
30
YELLOW
GREEN
H-E RED
20
10
20
10
0
0
1
2
3
0
4
FORWARD VOLTAGE VF (VOLTS)
20
40
60
80
INSTANTANEOUS FORWARD CURRENT IF (mA)
FIG. 1 - Forward Current vs. Forward Voltage
FIG. 2 - Luminous Intensity vs. Forward Current
GREEN
H-E RED
YELLOW
AIGaAs RED
300.0
200.0
100.0
50.0
100%
RELATIVE OUTPUT
IF — FORWARD CURRENT — mA
120%
20.0
10.0
5.0
2.0
1.0
.5
80%
60%
40%
20%
.2
.1
0
.5
1.0
1.5
2.0
2.5
3.0
3.5
VF — FORWARD VOLTAGE — V
FIG. 3 - Forward Current vs. Forward Voltage—AIGaAs
0%
520 540 560 580 600 620 640 660 680 700
WAVELENGTH (l) — nm
FIG. 4 - Spectral Distribution
SUBMINIATURE T-3/4 LED
DIFFUSED and CLEAR LAMPS
OPTIONAL CONFIGURATIONS
PACKAGE DIMENSIONS
DESCRIPTION
GULLWING LEAD CONFIGURATION
.087 (2.2)
.079 (2.0)
ANODE
CATHODE
.020 (.5)
.012 (.3)
.024 (.6)
.016 (.4)
Automatic placement equipment can be used to mount the
LEDs on the PC board. The lamps can be mounted using
either batch or in line vapor phase reflow solder processes.
.091 (2.3)
.083 (2.1)
.154 (3.90)
.148 (3.75)
These subminiature solid state lamps are transfer molded
in an axial lead package. They are available in yellow,
green, high efficiency red and AIGaAs red in both diffused
and water clear lens.
FEATURES
.058 (1.48)
.050 (1.28)
.039 (1.0)
.028 (.7)
■
■
CATHODE
■
.010 (.26)
.002 (.06)
■
.033 (.82)
.000 (.00)
.016 (.4)
.008 (.2)
■
.078 (1.9)
.063 (1.6)
Available in Gullwing, Yoke and Z-bend lead formings
Compatible with automatic placement equipment
Compatible with vapor phase reflow soldering processes
Long life — solid state reliability
Reel and tape or bulk packaging available
NOTE:
ALL DIMENSIONS ARE IN INCHES (mm)
.115 (2.92)
.099 (2.52)
CATHODE MARK
Z-BEND LEAD CONFIGURATION
.240 (1.6)
.232 (5.9)
YOKE LEAD CONFIGURATION
.087 (2.2)
.079 (2.0)
CATHODE
.020 (.5)
.012 (.3)
.020 (.5)
.012 (.3)
.024 (.6)
.016 (.4)
.024 (.6)
.016 (.4)
ANODE
ANODE
.091(2.3)
.083 (2.1)
.300 (7.62) MAX
.047 (1.2)
.031 (0.8)
.010 (.26)
.002 (.06)
.048 (1.22)
.032 (.82)
.087 (2.2)
.079 (2.0)
CATHODE
.189 (4.8)
.173 (4.4)
CATHODE
.033 (.85)
.026(.65)
.034 (.86)
.026 (.66)
.010 (.26)
.002 (.06)
CATHODE
.033 (.85)
.026 (.65)
.091 (2.3)
.083 (2.1)
.039 (.99)
.023 (.59)
.117 (2.96)
.100 (2.56)
.128 (3.24)
.112 (2.84)
CATHODE
.078 (1.9)
.063 (1.6)
.115 (2.92)
.099 (2.52)
.058 (1.48)
.050 (1.28)
.058 (1.48)
.050 (1.28)
.078 (1.9)
.063 (1.6)
CATHODE MARK
Call QT Optoelectronics for more information or the phone number of your nearest distributor.
United States 800-533-6786 France 33 01/43.99.25.12 Germany 49 089/96.30.51 United Kingdom 44 01296/39.44.99 Asia/Pacific 603/735-2417
■
© 1996 QT Optoelectronics QT-009-A
■
■
■
DS 100
Similar pages