FPIR32 MPIR40 KPIR50 MINIBRIDGE FAST RECOVERY, 32, 40 and 50 AMPERES INTEGRALLY MOLDED HEAT SINKS PROVIDE VERY LOW THERMAL RESISTANCE This mark indicates recognition under the component program of Underwriters Laboratories, inc. Our unique case construction enables the closer molding of integrated heat sink to the active components for a superior thermal transfer and lower junction temperatures. SERIES 50V 100V 200V 400V 600V 800V 1000V FPIR SERIES FPIR 3205 FPIR 3210 FPIR 3220 FPIR 3240 FPIR 3260 FPIR 3280 FPIR 32100 MPIR SERIES MPIR 4005 MPIR 4010 MPIR 4020 MPIR 4040 MPIR 4060 MPIR 4080 MPIR 40100 KPIR SERIES KPIR 5005 KPIR 5010 KPIR 5020 KPIR 5040 KPIR 5060 KPIR 5080 KPIR 50100 ELECTRICAL CHARACTERISTICS PER LEG (at TA =25 C U nle ss O the rwis e Sp ecif ied ) SERIES FPIR 32 MPIR 40 KPIR 50 UNITS Average Output Current, lo@ Tc(Fig.1) 32 40 50 Amp Max.Forward Voltage Drop,VF @ I F=12A (300 sec pulse) 1.4 1.4 1.4 Volts Max.DC Reverse Current @ PRV and 25 C , IR 10 10 15 A Max.DC Reverse Current @ PRV and 100 C ,IR 100 100 150 A Max.Peak Surge Current, lFSM (8.3ms) (Fig.2) 240 320 900 Amp Max. Reverse Recovery Time,Trr (Fig.3) 250 250 250 Nns. Storage Temperature Range,TSTG -55 to+150 Ambient Operating Temperature Range,TA -55 to+150 Thermal Resistance (Total Bridge), R0- j-c 1.5 typ. 1.2 typ. o C o C 0.8 typ. EDI reserves the rightto change these specifications at any time without notice. o C/W FPIR32 MPIR40 KPIR50 FIG.2 NON-REPETITIVE SURGE CURRENT FIG.1 CURRENT DERATING 1000 60 lO.AVERAGE L FORWARD CURRENT(AMP) KPIR50 MAX.PEAK SURGE CURRENT IFSM 50 MPIR40 40 30 FPIR32 20 BRIDGE OUTPUT RES.-IND. LOADS 10 500 KPIR50 MPIR40 200 100 FPIR32 50 20 Derate current by 20% for capacitive loads 0 10 0 25 O 50 O 75 O O 100 125 O 150 O 1 5 2 10 20 50 100 NUMBER OF CYCLES AT 60 CPS O TC =TEMPERATURE( C) FIG. 3 REVERSE RECOVERY TEST METHOD T RR R1 50 OHM ZERO D.U.T. + REFERENCE 0.5A - 1.0A 0.25A PULSE GENERATOR R2 1 OHM SCOPE R1, R2 NON-INDUCTIVE RESISTORS PULSE GENERATOR - HEWLETT PACKARD 214A OR EQUIV. IKC REP.RATE, 10 SEC. PULSE WIDTH ADJUST PULSE AMPLITUDE FOR PEAK IR MPIR40 and FPIR32 MECHANICAL OUTLINE Dielectric test voltage 2500 volts rms, max. 50-60Hz .093 DIA. HOLE 1.125 .032 S + .250 FASTON 4 PLACES EPOXY CASE .193 DIA THRU HOLE .6 MAX. 1.125 . 405 MAX S - INTEGRATED METAL HEAT SINK 1. Corrosion resistant terminals designed for .250 female quick connector, wrap around or solder. 2. A thin film of silicone thermal compound is recommended between the Minibridge R case and mounting surface for improved thermal conduction. 3. Higher dielectric strengths available. Consult factory. NOTE Maximum lead and terminal temperature for soldering, 3/8 inch from case, 5 seconds at 250 C ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951. 21 GRAY OAKS AVENUE * YONKERS. NEW YORK 10710 914-965-4400 Ee-mail:[email protected] *Wwebsite: http://www.edidiodes.com * FAX 914-965-5531 * 1-800-678-0828