150 Watts LPQ150 Series Total Power: 110-150 Watts Input Voltage: 85-132 / 170-264 VAC 220-300 VDC # of Outputs: Quad Electrical Specs Input Input range 85-132 VAC or 170-264 VAC automatically selected. 220-300 VDC 47-63 Hz 38 A max, cold start @ 25°C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted Frequency Inrush current Efficiency EMI filter Safety ground leakage current Special Features • • • • • • • • • • • Auto ranging input Remote sense on main output Remote inhibit Single wire current sharing Power fail Built-in EMI filter Low output ripple 135 khz switching frequency Overvoltage protection Overload protection Adjustable floating 4th output (On LPQ152 and LPQ153 models) • Optional cover (-C suffix). See page 64. Environmental Output Maximum power Adjustment range Cross regulation Hold-up time Overload protection Overvoltage protection Power failure Remote inhibit Electromagnetic susceptibility: designed to meet IEC 801, -2, -3, -4, -5, -6, Level 3 Remote sense Humidity: Operating; non-condensing 5% to 95% Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational Temperature coefficient: ± .04% per °C MTBF demonstrated: >550,000 hours at full load and 25°C ambient condition TTL logic signal goes high 50-150 msec after 5 V output. It goes low at least 3 msec before loss of regulation Requires an external TTL high signal to inhibit outputs Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. Safety VDE UL CSA NEMKO CB CE 114 110 W convection (75 W with cover) 150 W with 30 CFM forced air (130 W with cover) ±5% on main; 5-25 V on 4th output on LPQ 152 & LPQ 153 ±2% on output 1; ±3% on outputs 2, 3 &4 20 ms @110 W load at nominal line Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating 5.7-6.7 VDC on main output Logic Control Operating temperature: 0° to 50°C ambient derate each output at 2.5% per degree from 50° to 70°C Storage temperature: -40° to 85°C 0.5 mA @ 50/60 Hz, 264 VAC input 0805/EN60950 (IEC950) UL1950 CSA 22.2-234 Level 3 EN 60950/EMKO-TUE (74-sec) 203 Certificate and report Mark (LVD) 11774-3336-1260 (LC# 88585) EI32002 LR53982 P95102999 2061 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 rev 12.10.03 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 LPQ150 Series Ordering Information Regulation2 Model Output Minimum Maximum Load with Maximum Load with Peak Number Voltage Load Convection Cooling 30 CFM Forced Air Load1 LPQ152 5V 12 V -12 V ±5-25 V 2A .1 A .1 A 0A 15 A 6A 2A 2.5 A 22 A 8A 2.5 A 3A 30 A 10 A 3A 3A ±2% ±3% ±3% ±3% 50 mV 120 mV 120 mV 240 mV, max. LPQ153 5V 15 V -15 V ±5-25 V 2A .1 A .1 A 0A 15 A 4.8 A 1.6 A 2.5 A 22 A 6.4 A 2A 3A 30 A 8A 2.4 A 3A ±2% ±3% ±3% ±3% 50 mV 150 mV 150 mV 240 mV, max. LPQ154 5V 12 V -12 V 24 V 2A .1 A .1 A .5 A 15 A 6A 2A 3.5 A 22 A 8A 2.5 A 4.5 A 30 A 10 A 3A 5A ±2% ±3% ±3% +10 / -5% 50 mV 120 mV 120 mV 240 mV 1. 2. 3. 4. 5. Ripple P/P (PARD)3 Peak current lasting <30 seconds with a maximum 10% duty cycle. At 25°C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4th output adjustable 5-25 V factory set at 5 V. Minimum loads are required. SK3 LPQ152 INHIBIT -ve INHIBIT +ve +12 V No Connection COMMON -SENSE +SENSE LPQ153 INHIBIT -ve INHIBIT +ve +15 V No Connection COMMON -SENSE +SENSE LPQ154 INHIBIT -ve INHIBIT +ve +12 V No Connection COMMON -SENSE +SENSE PIN 8 SK2 PIN 1,2 PIN 3,4,5 PIN 6 PIN 7 PIN 8 I SHARE +12 V COMMON -12 V POK +5 V to +25 V (Float) I SHARE +15 V COMMON -15 V POK +5 V to +25 V (Float) I SHARE +12 V COMMON -12 V POK +24 V PIN 9 SK3 TB-1 COMMON (Float) COMMON COMMON (Float) COMMON COMMON COMMON TB-2 SK4 PIN 1 PIN 3 PIN 5 +5 V GROUND LINE NEUTRAL +5 V GROUND LINE NEUTRAL +5 V GROUND LINE NEUTRAL Mating Connectors (SK4) AC Input: Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 (SK2) Aux DC Output/Power fail: Molex 09-50-8091 (USA) Molex 09-91-0900 (UK) PINS: 08-58-0111 (SK1) Remote sense/Remote inhibit: Molex 51110-0851 (USA) PINS: 503-94-8100 2 1 SK2 #6-32 UNC (8 places) 1234 .5625 987654321 4th O/P ADJ Connector SK1 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 SK1 8765 5V O/P ADJ Pin Assignments DO NOT ADJ Note: -C suffix added to the model number indicates cover option. 7.4 (188.0) 8.5 (216.0) Notes 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ±0.02”. 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Remote inhibit requires an external 5V @ 10mA to activate. 5. Mounting (6-32) maximum insertion depth is 0.12”. 6. Warranty: 1 year 7. Weight: 1.75 lb. / 0.80 kg 531 SK4 4.25 (108.0) .875 (22.25) .75 (19.0) 1.5 (38.1) 2.5 (63.5) Astec Connector Kit #70-841-010, includes al of the above. www.astecpower.com 115