ES1AW THRU ES1JW Surface Mount Superfast Recovery Rectifier Reverse Voltage – 50 to 600 V PINNING Forward Current – 1 A PIN FEATURES • Easy pick and place • For surface mounted applications • Low profile package • Built-in strain relief • Superfast recovery times for high efficiency DESCRIPTION 1 Cathode 2 Anode 1 2 Simplified outline SOD-123FL and symbol MECHANICAL DATA • Case: SOD-123FL • Terminals: Solderable per MIL-STD-750, Method 2026 • Approx. Weight:15mg 0.00053oz Absolute Maximum Ratings and Characteristics Ratings at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Symbols Parameter ES1AW ES1BW ES1CW ES1DW ES1EW ES1GW ES1JW Units Maximum Repetitive Peak Reverse Voltage V RRM 50 100 150 200 300 400 600 V Maximum RMS voltage V RMS 35 70 105 140 210 280 420 V Maximum DC Blocking Voltage V DC 50 100 150 200 300 400 600 V Maximum Average Forward Rectified Current at T L = 100 °C I F(AV) 1 A Peak Forward Surge Current 8.3 ms Single Half Sine Wave Superimposed on Rated Load (JEDEC Method) I FSM 30 A Maximum Forward Voltage at 1 A VF Maximum DC Reverse Current at Rated DC Blocking Voltage Ta = 25 °C Ta =125 °C Typical Junction Capacitance at V R =4V, f=1MHz Maximum Reverse Recovery Time 1） Typical Thermal Resistance 2） Operating and Storage Temperature Range 1.25 1 1.68 V IR 5 100 μA Cj 10 pF t rr 35 ns RθJA 120 °C/W T j , T stg -55 ~ +150 °C 1）Measured with I F = 0.5 A, I R = 1 A, I rr = 0.25 A 2）P.C.B. mounted with 0.2 X 0.2" (5 X 5 mm) copper pad areas. ES1AW THRU ES1JW Fig.1 Reverse Recovery Time Characteristic And Test Circuit Diagram 50 ohm Noninductive 10 ohm Noninductive t rr +0.5 D.U.T + PULSE GENERATOR Note 2 25Vdc approx - 0 -0.25 1 ohm OSCILLOSCOPE Note 1 NonInductive -1.0 Note：1.Rise Time = 7ns, max. Input Impedance = 1megohm,22pF. 2. Ries Time =10ns, max. Source Impedance = 50 ohms. 10ns/div Set time Base for 10ns/div Fig.3 Typical Reverse Characteristics 300 1.2 1.0 I R - Reverse Current ( μ A) Average Forward Current (A) Fig.2 Maximum Average Forward Current Rating 0.8 0.6 0.4 Single phase half wave resistive or inductive P.C.B mounted on 0.2×0.2"(5×5mm ) pad areas 0.2 100 T J =125°C 10 T J =75°C 1.0 T J =25°C 0.1 0.0 25 50 75 100 125 150 175 0 Lead Temperature (°C) 80 100 14 10 T J =25°C Junction Capacitance ( pF) Instaneous Forward Current (A) 60 Fig.5 Typical Junction Capacitance 1.0 ES1AW~ES1DW ES1EW/WS1GW 0.1 ES1JW 0.01 0.001 0 0.5 1.5 1.0 2.0 2.5 Instaneous Forward Voltage (V) 35 30 25 20 15 10 8.3 ms Single Half Sine Wave (JEDEC Method) 05 1 10 Number of Cycles 12 10 8 6 T J =25°C f = 1.0MHz V sig = 50mV p-p 4 2 0.1 1 10 Reverse Voltage (V) Fig.6 Maximum Non-Repetitive Peak Forward Surage Current Peak Forward Surage Current (A) 40 % of PIV.VOLTS Fig.4 Typical Forward Characteristics 00 20 100 100 ES1AW THRU ES1JW PACKAGE OUTLINE Plastic surface mounted package; 2 leads SOD-123FL ∠ALL ROUND C A ∠ALL ROUND VM D E A g Top View mil Bottom View A C D E e g HE max 1.1 0.20 2.9 1.9 1.1 0.9 3.8 min 0.9 0.12 2.6 1.7 0.8 0.7 3.5 max 43 7.9 114 75 43 35 150 min 35 4.7 102 67 31 28 138 UNIT mm g pad e E A pad HE The recommended mounting pad size 1.2 (47) 1.2 (47) 2.0 (79) 7° Marking Type number 1.2 (47) ∠ Unit： mm (mil) Marking code ES1AW E1A ES1BW E1B ES1CW E1C ES1DW E1D ES1EW E1E ES1GW E1G ES1JW E1J