E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film QPL MIL-PRF-55342 Qualified Thin Film Resistor, Surface Mount Chip FEATURES Thin Film Mil chip resistors feature all sputtered wraparound termination for excellent adhesion and dimensional uniformity. They are ideal in applications requiring stringent performance requirements. Established reliability is assured through 100 % screening and extensive environmental lot testing. CONSTRUCTION Passivation Resistor Film Solder Coating • Established reliability, "S" and "V" failure rate level (10 ppm), C = 2 • High purity alumina substrate • Wraparound termination featuring a tenacious adhesion layer covered with an electroplated nickel barrier layer for +150 °C operating conditions • Very low noise and voltage coefficient (< -25 dB, 0.5 ppm/V) • Non-inductive • Laser-trimmed tolerances ± 0.1 % • Wraparound resistance less than 0.010 typical • In-lot tracking less than 5 ppm/°C • Complete MIL-testing available in-house • Antistatic waffle pack or tape and reel packaging available • Military/aerospace/QPL TYPICAL PERFORMANCE ABSOLUTE Nickel Barrier High Purity Alumina Substrate Adhesion Layer TCR 25 TOL. 0.1 STANDARD ELECTRICAL SPECIFICATIONS TEST Material Resistance Range TCR: Absolute Tolerance: Absolute Stability: Absolute Stability: Ratio Voltage Coefficient Working Voltage Operating Temperature Range Storage Temperature Range Noise Shelf Life Stability: Absolute SPECIFICATIONS Tamelox resistor film (passivated nichrome) 10 to 6.19 M ± 25 ppm/°C to ± 300 ppm/°C ± 0.1 % to ± 10 % R ± 0.02 % 0.1 ppm/V 30 V to 200 V -55 °C to +150 °C -55 °C to +150 °C < - 25 dB R ± 0.01 % CONDITIONS -55 °C to +125 °C +25 °C 2000 h at +70 °C 1 year at +25 °C COMPONENT RATINGS CASE SIZE POWER RATING (mW) 50 125 200 150 225 150 250 800 1000 500 50 100 RESISTANCE RANGE () BY CHARACTERISTICS TOLERANCE WORKING VOLTAGE E E H, K, L, M H, K, L, M (V) (0.1 %, 0.25 %, 0.5 %) (1 %, 2 %, 5 %) (0.1 %, 0.25 %, 0.5 %) (1 %, 2 %, 5 %) 40 49.9 to 150K 49.9 to 150K 20 to 150K 20 to 150K 40 49.9 to 301K 49.9 to 301K 20 to 301K 20 to 301K 75 49.9 to 649K 49.9 to 649K 10 to 649K 10 to 649K 125 49.9 to 1.69M 49.9 to 1.69M 10 to 1.69M 10 to 1.69M 175 49.9 to 3.16M 49.9 to 3.16M 10 to 3.16M 10 to 3.16M 50 49.9 to 475K 49.9 to 475K 10 to 475K 10 to 475K 100 49.9 to 1.5M 49.9 to 1.5M 10 to 1.5M 10 to 1.5M 150 49.9 to 4.02M 49.9 to 4.02M 10 to 4.02M 10 to 4.02M 200 49.9 to 6.19M 49.9 to 6.19M 10 to 6.19M 10 to 6.19M 75 49.9 to 1M 49.9 to 1M 49.9 to 1M 49.9 to 1M 30 49.9 to 100K 49.9 to 100K 20 to 100K 20 to 100K 50 49.9 to 258K 49.9 to 261K 10 to 258K 10 to 261K M55342/01 M55342/02 M55342/03 M55342/04 M55342/05 M55342/06 D55342/07 M55342/08 M55342/09 M55342/10 M55342/11 M55342/12 Note • Values listed are a guide, refer to MIL spec for value/tolerance allowance Revision: 04-Nov-14 Document Number: 60018 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film DIMENSIONS in inches D W T E L CASE SIZE TERM. L W T D E M55342/01 B 0.055 ± 0.006 0.025 ± 0.005 0.010 to 0.030 0.010 ± 0.005 0.015 ± 0.005 M55342/02 B 0.055 ± 0.006 0.050 ± 0.005 0.012 to 0.033 0.010 ± 0.005 0.015 ± 0.005 M55342/03 B 0.105 ± 0.007 0.050 ± 0.005 0.015 to 0.033 0.015 ± 0.005 0.015 ± 0.005 M55342/04 B 0.155 ± 0.007 0.050 ± 0.005 0.015 to 0.033 0.015 ± 0.005 0.015 ± 0.005 M55342/05 B 0.230 ± 0.007 0.075 ± 0.005 0.015 to 0.033 0.020 ± 0.005 0.020 ± 0.005 0.016 ± 0.008 0.015 ± 0.005 M55342/06 B 0.080 ± 0.006 0.050 ± 0.005 0.015 to 0.033 D55342/07 B 0.126 ± 0.008 0.063 ± 0.005 0.015 to 0.033 M55342/08 B 0.209 + 0.009/- 0.018 0.098 ± 0.005 0.015 to 0.033 0.020 ± 0.005 M55342/09 B 0.259 + 0.009/- 0.015 0.124 ± 0.005 0.015 to 0.033 0.020 ± 0.005 0.020 ± 0.005 M55342/10 B 0.105 ± 0.007 0.100 ± 0.005 0.015 to 0.033 0.015 ± 0.005 0.015 ± 0.005 M55342/11 B 0.040 ± 0.005 0.025 ± 0.005 0.010 to 0.030 0.010 ± 0.005 0.015 ± 0.005 M55342/12 B 0.064 ± 0.006 0.032 ± 0.005 0.010 to 0.033 0.012 ± 0.005 0.015 ± 0.005 0.020 + 0.005/- 0.010 0.020 + 0.005/- 0.010 0.020 ± 0.005 ENVIRONMENTAL TESTS MIL-PRF-55342 LIMITS (R ±) VISHAY PERFORMANCE (R ±) Thermal Shock 0.1 % 0.020 % Low Temperature Operation 0.1 % 0.025 % Short Time Overload 0.1 % 0.050 % High Temperature Exposure 0.1 % 0.009 % Resistance to Bonding 0.2 % 0.006 % Moisture Resistance 0.2 % 0.004 % ± 25 ppm/°C < 15 ppm/°C Life (2000 h at + 70 °C) 0.5 % 0.02 % Life (10 000 h at + 70 °C) 2.0 % 0.04 % ENVIRONMENTAL TEST TCR MECHANICAL SPECIFICATIONS Resistive Element Tamelox Substrate Material Alumina Chip Terminations Solder over nickel Fused Solder Revision: 04-Nov-14 FSCM CAGE # - 57489 Plated solder 90/10 Document Number: 60018 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 E/H (Military M/D55342) www.vishay.com Vishay Dale Thin Film Percent of Rated Wattage DERATING 100 80 60 40 20 0 -75 -50 -25 0 25 50 75 100 125 150 175 Ambient Temperature °C GLOBAL PART NUMBER INFORMATION New Global Part Numbering: M55342E06B1C00RTS M 5 5 3 GLOBAL TCR MODEL CHARACTERISTIC M55342 or D55342 (/07 size only) E = 25 ppm/°C H = 50 ppm/°C K = 100 ppm/°C L = 200 ppm/°C M = 300 ppm/°C 4 CASE SIZE 01 = 0502 02 = 0505 03 = 1005 04 = 1505 05 = 2208 06 = 0705 07 = 1206 08 = 2010 09 = 2512 10 = 1010 11 = 0402 12 = 0603 2 E 0 6 TERMINATION B = Solderable B 1 C 0 0 FAILURE RATE OHMIC VALUE M N P T S V THIN FILM CODE (1) PACKAGING Three digits and a letter. Letter M = 1.0 % identifies tolerance, acts as per 1000 h multiplier and decimal locator. P = 0.1 % per 1000 h MULTIPLIER R = 0.01 % Tolerance 1 1 k 1 M per 1000 h U = 0.01 % 0.1 % A B C per 1000 h(3) 0.25 % R U V S = 0.001 % per 1000 h 0.5 % W Y Z V = 0.001 % 1% D E F per 1000 h (3) 2% G H T C = Non ER version 5% J K L 10 % R Standard Packaging: V BS = BULK for 100 min., 1 mult K, L and M WS =WAFFLE TCR 100 min., 1 mult W/tolerance W0 =WAFFLE 1% 100 min.,100 mult M = Part TAPE AND REEL marked (2) T0 = 100 min., 100 mult T1 = 1000 min., 1000 mult T3 = 300 min., 300 mult T5 = 500 min., 500 mult TF = Full reel ( 2K, 4K, or 5K dependent on case size ) per tape and reel document 60034 TS = 100 min., 1 mult Special Packaging: WAFFLE WI = 100 min., 1 mult (item single lot date code) WP =100 min., 1 mult (package unit single lot date code) TAPE AND REEL TI = 100 min., 1 mult (item single lot date code) TP = 100 min., 1 mult (package unit single lot date code) Historical Part Number example: M55342K06B5E60R (for reference purposes only) M55342 K 06 B 5E60 R SERIES TCR CHARACTERISTIC CASE SIZE TERMINATION VALUE AND TOLERANCE FAILURE RATE Notes (1) Only add a V at the end of part number to specify Vishay Dale Thin Film for K, L and M TCR and tolerance 1 % and higher. (2) Option 1 marking only. Case sizes 01, 02, 11, and 12 not available due to size. (3) Failure Rate U and V require Group A and B testing on a Production Lot Basis. Revision: 04-Nov-14 Document Number: 60018 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000