EPCOS B43896A9336M000 Aluminum electrolytic capacitor Datasheet

Aluminum electrolytic capacitors
Single-ended capacitors
Series/Type:
B43896
Date:
December 2006
 EPCOS AG 2007. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Single-ended capacitors
B43896
Up to 125 °C
Long-life grade capacitors
Applications
Automotive (piezo injection)
Energy-saving lamps
Power supplies
Features
High ripple current capability
Wide temperature range
Construction
Radial leads
Charge-discharge proof, polar
Aluminum case with insulating sleeve
Minus pole marking on the insulating sleeve
Stand-off rubber seal
Case with safety vent
Delivery mode
Terminal configurations and packing:
Bulk
Taped, Ammo pack
Cut
Kinked
PAPR (protection against polarity reversal):
crimped leads, J leads, bent leads
Refer to chapter "Single-ended capacitors Taping, packing
and lead configurations" for further details and ordering
example.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 2 of 24
B43896
Up to 125 °C
Specifications and characteristics in brief
Rated voltage VR
Surge voltage VS
160 ... 450 V DC
1.1 VR
Rated capacitance CR
Capacitance tolerance
4.7 ... 220 µF
±20% M
Dissipation factor tan δ
(20 °C, 120 Hz)
VR ≤ 250 V DC: tan δ = 0.20
VR ≥ 350 V DC: tan δ = 0.24
Leakage current Ileak
(20 °C, 5 min)
Self-inductance ESL
Diameter (mm)
ESL (nH)
Useful life
125 °C, VR, IAC,R
Requirements
Voltage endurance test
125 °C, VR
Post test requirements
Vibration resistance test
≤ 12.5
16
18
20
26
34
> 3000 h
∆C/C
tan δ
Ileak
≤ ±35% of initial value
≤ 3 times initial specified limit
≤ initial specified limit
3000 h
∆C/C
≤ ±30% of initial value
tan δ
≤ 2 times initial specified limit
Ileak
≤ initial specified limit
To IEC 60068-2-6, test Fc:
Displacement amplitude 0.75 mm, frequency range 10 ... 2000 Hz,
acceleration max. 20 g, duration 3 × 2 h.
Capacitor rigidly clamped by the aluminum case.
IEC climatic category
To IEC 60068-1:
VR ≤ 250 V: 40/125/56 (40 °C/+125 °C/56 days damp heat test)
VR ≥ 350 V: 25/125/56 (25 °C/+125 °C/56 days damp heat test)
Sectional specification
IEC 60384-4
Please read Cautions and warnings and
Important notes at the end of this document.
Page 3 of 24
B43896
Up to 125 °C
Dimensional drawing
With stand-off rubber seal
Diameters (mm): 10, 12.5, 16, 18
Dimensions and weights
Dimensions (mm)
d +0.5
10
10
12.5
12.5
12.5
16
16
16
18
18
18
l
16 +1.0
20 +2.0
20 +2.0
25 +2.0
30 +2.0
20 +2.0
25 +2.0
31.5 +2.0
20 +2.0
31.5 +2.0
35 +2.0
Please read Cautions and warnings and
Important notes at the end of this document.
a ±0.5
5.0
5.0
5.0
5.0
5.0
7.5
7.5
7.5
7.5
7.5
7.5
Page 4 of 24
b
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.60 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.05
0.80 ±0.1
0.80 ±0.1
0.80 ±0.1
Approx. weight
g
1.9
2.6
3.6
4.5
5.3
5.5
7.5
7.8
8.0
11.0
13.0
B43896
Up to 125 °C
Overview of available types
VR (V DC)
160
200
250
350
400
450
Case dimensions d × l (mm)
CR (µF)
10
× 16
10
× 20
10
× 16
10
× 20
10
× 20
× 20
10
4.7
6.8
10
10
× 16
15
10
× 16
10
× 16
10
× 20
12.5 × 20
10
× 16
10
× 20
12.5 × 20
12.5 × 25
12.5 × 25
12.5 × 30
22
10
× 20
10
× 20
12.5 × 20
12.5 × 25
16
× 25
33
10
× 20
12.5 × 20
12.5 × 25
16
× 25
16
× 25
16
× 31.5
47
12.5 × 20
12.5 × 25
16
18
× 20
× 20
16
× 31.5
18
× 31.5
18
× 35
68
12.5 × 25
16
× 20
16
× 31.5
18
× 31.5
16
× 25
18
× 31.5
100
16
× 25
150
16
× 31.5
220
18
× 31.5
Other voltage and capacitance ratings are available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 5 of 24
B43896
Up to 125 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 160 V DC
10
10 × 16
22
10 × 20
33
10 × 20
47
12.5 × 20
68
12.5 × 25
100
16 × 25
150
16 × 31.5
220
18 × 31.5
VR = 200 V DC
10
10 × 16
15
10 × 16
22
10 × 20
33
12.5 × 20
47
12.5 × 25
68
16 × 20
100
16 × 25
VR = 250 V DC
10
10 × 16
15
10 × 20
22
12.5 × 20
33
12.5 × 25
47
16 × 20
47
18 × 20
68
16 × 31.5
100
18 × 31.5
ESRmax
120 Hz
25 °C
Ω
ESRmax
120 Hz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
IAC,max
100 kHz
105 °C
mA
Ordering code
(composition see
below)
774
352
234
165
114
77
52
35
22.1
10.0
6.7
4.7
3.3
2.2
1.5
1.0
4.64
2.11
1.41
0.99
0.68
0.46
0.31
0.21
150
225
277
281
368
494
651
830
210
290
388
393
515
692
911
1162
B43896A1106M***
B43896A1226M***
B43896A1336M***
B43896A1476M***
B43896A1686M***
B43896A1107M***
B43896A1157M***
B43896A1227M***
774
516
352
234
165
114
77
22.1
14.7
10.0
6.7
4.7
3.3
2.2
4.64
3.09
2.11
1.41
0.99
0.68
0.46
125
175
227
283
306
375
495
175
245
318
396
428
525
693
B43896A2106M***
B43896A2156M***
B43896A2226M***
B43896A2336M***
B43896A2476M***
B43896A2686M***
B43896A2107M***
774
516
352
234
165
165
114
77
22.1
14.7
10.0
6.7
4.7
4.7
3.3
2.2
4.64
3.09
2.11
1.41
0.99
0.99
0.68
0.46
120
130
170
231
257
460
338
438
168
182
203
323
360
644
473
613
B43896F2106M***
B43896F2156M***
B43896F2226M***
B43896F2336M***
B43896F2476M***
B43896G2476M***
B43896F2686M***
B43896F2107M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for ∅ ≥ 10 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm)
003 = for crimped leads, blister (for ∅ ≥ 16 mm)
004 = for J leads, blister (from d × l = 10 × 16 mm to 18 × 35 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 10 × 16 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 6 of 24
B43896
Up to 125 °C
Technical data and ordering codes
CR
120 Hz
20 °C
µF
Case
dimensions
d×l
mm
VR = 350 V DC
6.8
10 × 16
10
10 × 20
15
12.5 × 20
22
12.5 × 25
33
16 × 25
47
16 × 31.5
68
18 × 31.5
VR = 400 V DC
4.7
10 × 16
6.8
10 × 20
10
10 × 20
15
12.5 × 25
22
12.5 × 30
33
16 × 25
47
18 × 31.5
VR = 450 V DC
4.7
10 × 20
6.8
10 × 20
10
12.5 × 20
15
12.5 × 25
22
16 × 25
33
16 × 31.5
47
18 × 35
ESRmax
120 Hz
25 °C
Ω
ESRmax
120 Hz
20 °C
Ω
Zmax
100 kHz
20 °C
Ω
IAC,R
100 kHz
125 °C
mA
IAC,max
100 kHz
105 °C
mA
Ordering code
(composition see
below)
1365
928
619
422
281
198
137
39.0
26.5
17.7
12.1
8.0
5.6
3.9
8.19
5.57
3.71
2.53
1.69
1.19
0.82
100
155
200
250
341
365
480
140
217
280
350
477
511
672
B43896A4685M***
B43896A4106M***
B43896A4156M***
B43896A4226M***
B43896A4336M***
B43896A4476M***
B43896A4686M***
1975
1365
928
619
422
281
198
56.4
39.0
26.5
17.7
12.1
8.0
5.6
11.85
8.19
5.57
3.71
2.53
1.69
1.19
96
115
155
200
256
341
364
134
161
217
280
358
477
510
B43896A9475M***
B43896A9685M***
B43896A9106M***
B43896A9156M***
B43896A9226M***
B43896A9336M***
B43896A9476M***
1975
1365
928
619
422
281
198
56.4
39.0
26.5
17.7
12.1
8.0
5.6
11.85
8.19
5.57
3.71
2.53
1.69
1.19
105
110
155
200
277
365
480
147
154
217
280
388
511
672
B43896A5475M***
B43896A5685M***
B43896A5106M***
B43896A5156M***
B43896A5226M***
B43896A5336M***
B43896A5476M***
Composition of ordering code
*** = Version
000 = for standard leads, bulk
001 = for kinked leads, bulk (for ∅ ≥ 10 mm)
002 = for cut leads, bulk (for ∅ ≥ 10 mm)
003 = for crimped leads, blister (for ∅ ≥ 16 mm)
004 = for J leads, blister (from d × l = 10 × 16 mm to 18 × 35 mm)
008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 10 × 16 mm to 12.5 × 25 mm)
009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm)
012 = for bent 90° leads, blister (for ∅ 16 and 18 mm)
Please read Cautions and warnings and
Important notes at the end of this document.
Page 7 of 24
B43896
Up to 125 °C
Useful life
depending on ambient temperature TA under ripple current operating conditions1)
Frequency factor of permissible ripple current IAC versus frequency f
1)
Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life
graphs.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 8 of 24
B43896
Up to 125 °C
Taping, packing and lead configurations
Taping
Single-ended capacitors are available taped in Ammo pack from diameter 5 to 18 mm as follows:
Lead spacing F = 2.5 mm (∅ d = 5 … 6.3 mm)
Lead spacing F = 3.5 mm (∅ d = 8 mm)
Lead spacing F = 5.0 mm (∅ d = 5 … 12.5 mm)
Lead spacing F = 7.5 mm (∅ d = 16 ... 18 mm).
Lead spacing 2.5 mm (∅ d = 5 ... 6.3 mm)
Last 3 digits of ordering code: 007
Dimensions in mm
∅d
5
F
H
W
W0
W1
W2
H0
P
P0
P1
I1
t
∆h
D0
2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0
6.3
Toler- +0.8
±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2
ance 02
Please read Cautions and warnings and
Important notes at the end of this document.
Page 9 of 24
B43896
Up to 125 °C
Lead spacing 3.5 mm (∅ d = 8 mm)
Last 3 digits of ordering code: 006
Dimensions in mm
∅d
8
Tolerance
F
H
W
W0
W1
W2
P
P0
P1
I1
t
∆h
3.5
18.5
18.0
12.5
9.0
1.5
12.7
12.7
4.6
1.0
0.7
1.0
+0.8
02
1.0
±0.5
min.
±0.5
max. ±1.0
±0.2
±0.5
max. ±0.2
Please read Cautions and warnings and
Important notes at the end of this document.
Page 10 of 24
D0
4.0
max. ±0.2
B43896
Up to 125 °C
Lead spacing 5.0 mm (∅ d = 5 ... 8 mm)
Last 3 digits of ordering code: 008
Lead spacing 5.0 mm (∅ d = 10 ... 12.5 mm)
Last 3 digits of ordering code: 008
Dimensions in mm
∅d
5
6.3
F
H
W
W0
W1
W2
H0
P
P0
P1
I1
t
∆h
D0
5.0
18.5
18.0 5.5
9.0
1.5
16.0
12.7
12.7
3.85
1.0
0.7
1.0
4.0
16.0
12.7
12.7
3.85
18.0 12.5 9.0
1.5
12.7
12.7
3.85
1.0
0.7
1.0
4.0
15.0
15.0
5.0
±1.0
±0.2
±0.5
8
10
20.0
5.0
12.5
Toler- +0.8
ance 02
19.0
19.0
±0.75 ±0.5 min. ±0.5 max. ±0.5
Please read Cautions and warnings and
Important notes at the end of this document.
Page 11 of 24
max. ±0.2 max. ±0.2
B43896
Up to 125 °C
Lead spacing 7.5 mm (∅ d = 16 ...18 mm)
Last 3 digits of ordering code: 009
Dimensions in mm
∅d
16
F
H
W
7.5 18.5 18.0
18 *)
Toler0.5
±0.8
±0.5
ance
+0.75
W0
W1
W2
P
P0
P1
I1
t
∆P
∆h
D0
12.5
9.0
1.5
30.0
15.0
3.75
1.0
0.7
0
0
4.0
min.
±0.5
max. ±1.0
±0.2
±0.5
max. ±0.2 ±1.0 ±1.0 ±0.2
*) Available only for case dimensions 18 × 20, 18 × 25 and 18 × 31.5 mm
Please read Cautions and warnings and
Important notes at the end of this document.
Page 12 of 24
B43896
Up to 125 °C
Packing units and box dimensions
Ammo pack
Please read Cautions and warnings and
Important notes at the end of this document.
Case size
d×l
mm
Dimensions (mm)
Amax
Bmax
Cmax
5 × 11
345
55
240
2000
6.3 × 11
345
55
290
2000
8 × 11.5
345
55
240
1000
10 × 12.5
345
55
280
750
10 × 16
345
60
200
500
10 × 20
345
60
200
500
12.5 × 20
345
65
280
500
12.5 × 25
345
65
280
500
12.5 × 25
345
65
280
500
12.5 × 30
345
65
275
500
16 × 20
315
65
275
300
16 × 25
315
65
275
300
16 × 31.5
315
65
275
300
18 × 20
315
65
275
250
18 × 25
315
65
275
250
18 × 31.5
315
65
275
250
Page 13 of 24
Packing
units
pcs.
B43896
Up to 125 °C
Kinked or cut leads
Single-ended capacitors are available with kinked or cut leads. Other lead configurations also
available upon request.
Kinked leads
Last 3 digits of ordering code: 001
With stand-off rubber seal
Case size
d × l (mm)
With flat rubber seal
Please read Cautions and warnings and
Important notes at the end of this document.
Page 14 of 24
Dimensions (mm)
a ±0.5
10 × 20
5.0
12.5 × 20
5.0
12.5 × 25
5.0
12.5 × 30
5.0
12.5 × 35
5.0
12.5 × 40
5.0
16 × 20
7.5
16 × 25
7.5
16 × 31.5
7.5
18 × 20
7.5
18 × 25
7.5
18 × 31.5
7.5
18 × 35
7.5
18 × 40
7.5
20 × 20
10.0
20 × 25
10.0
20 × 40
10.0
22 × 30
10.0
22 × 35
10.0
22 × 40
10.0
B43896
Up to 125 °C
Cut leads
Last 3 digits of ordering code: 002
With stand-off rubber seal
Case size
d × l (mm)
With flat rubber seal
Please read Cautions and warnings and
Important notes at the end of this document.
Page 15 of 24
Dimensions (mm)
a ±0.5
10 × 12.5
5.0
10 × 16
5.0
10 × 20
5.0
12.5 × 20
5.0
12.5 × 25
5.0
12.5 × 30
5.0
12.5 × 35
5.0
12.5 × 40
5.0
16 × 20
7.5
16 × 25
7.5
16 × 31.5
7.5
18 × 20
7.5
18 × 25
7.5
18 × 31.5
7.5
18 × 35
7.5
18 × 40
7.5
20 × 20
10.0
20 × 25
10.0
20 × 40
10.0
B43896
Up to 125 °C
PAPR leads (Protection Against Polarity Reversal)
These lead configurations ensure correct placement of the capacitor on the PCB with regard to
polarity. PAPR leads are available for diameters from 10 mm up to 20 mm.
There are three configurations available: Crimped leads, J leads, bent 90° leads
Crimped leads
Last 3 digits of ordering code: 003
With stand-off rubber seal
With flat rubber seal
Suggestion for PCB hole diameter
Case size
d × l (mm)
Dimensions (mm)
B ±0.2
C ±0.5
D ±0.1
E ±0.1
16 × 20
1.5
3.0
1.3
0.3
7.5
0.8 ±0.05
16 × 25
1.5
3.0
1.3
0.3
7.5
0.8 ±0.05
16 × 31.5
1.5
3.0
1.3
0.3
7.5
0.8 ±0.05
18 × 20
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
18 × 25
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
18 × 31.5
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
18 × 35
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
18 × 40
1.5
3.0
1.3
0.3
7.5
0.8 ±0.1
20 × 20
1.5
3.0
1.6
0.3
10.0
1.0 ±0.1
20 × 25
1.5
3.0
1.6
0.3
10.0
1.0 ±0.1
20 × 40
1.5
3.0
1.6
0.3
10.0
1.0 ±0.1
Please read Cautions and warnings and
Important notes at the end of this document.
Page 16 of 24
a ±0.5
∅b
B43896
Up to 125 °C
J leads
Last 3 digits of ordering code: 004
Suggestion for PCB hole diameter
Case size
d × l (mm)
Dimensions (mm)
C ±0.5
E ±0.5
J ±0.2
10 × 12.5
3.2
0.7
1.2
5.0
0.6 ±0.05
10 × 16
3.2
0.7
1.2
5.0
0.6 ±0.05
10 × 20
3.2
0.7
1.2
5.0
0.6 ±0.05
12.5 × 20
3.2
0.7
1.2
5.0
0.6 ±0.05
12.5 × 25
3.2
0.7
1.2
5.0
0.6 ±0.05
16 × 20
3.5
0.7
1.6
7.5
0.8 ±0.05
16 × 25
3.5
0.7
1.6
7.5
0.8 ±0.05
16 × 31.5
3.5
0.7
1.6
7.5
0.8 ±0.05
18 × 20
3.5
0.7
1.6
7.5
0.8 ±0.1
18 × 25
3.5
0.7
1.6
7.5
0.8 ±0.1
18 × 31.5
3.5
0.7
1.6
7.5
0.8 ±0.1
18 × 35
3.5
0.7
1.6
7.5
0.8 ±0.1
Please read Cautions and warnings and
Important notes at the end of this document.
Page 17 of 24
a ±0.5
∅b
B43896
Up to 125 °C
Bent 90° leads for horizontal mounting pinning
Last 3 digits of ordering code: 012
Case size
d × l (mm)
Dimensions (mm)
C ±0.5
E ±0.5
F ±0.5
a ±0.5
∅b
16 × 20
4.0
4.0
12.0
7.5
0.8 ±0.05
16 × 25
4.0
4.0
12.0
7.5
0.8 ±0.05
16 × 31.5
4.0
4.0
12.0
7.5
0.8 ±0.05
18 × 20
4.0
4.0
13.0
7.5
0.8 ±0.1
18 × 25
4.0
4.0
13.0
7.5
0.8 ±0.1
18 × 31.5
4.0
4.0
13.0
7.5
0.8 ±0.1
18 × 35
4.0
4.0
13.0
7.5
0.8 ±0.1
18 × 40
4.0
4.0
13.0
7.5
0.8 ±0.1
Bent leads for diameter 12.5 mm available upon request.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 18 of 24
B43896
Up to 125 °C
Overview of packing units and code numbers for case sizes 5 × 11 ... 16 × 31.5
PAPR
Case size
d×l
Taped,
Ammo pack
mm
Standard,
bulk
pcs.
5 × 11
2000
6.3 × 11
2500
2000
8 × 11.5
1000
1000
10 × 12.5
1000
750
10 × 16
100
500
1000
10 × 20
500
500
500
500
12.5 × 20
350
500
350
350
12.5 × 25
250
500
500
500
12.5 × 30
200
500
175
175
12.5 × 35
175
-
175
175
12.5 × 40
175
-
175
175
16 × 20
250
300
200
200
16 × 25
250
300
200
16 × 31.5
200
300
The last three
digits of the
complete
ordering code
state the lead
configuration
000
Code
006
007
008
009
1)
pcs.
Kinked
leads,
bulk
pcs.
Cut
Crimped J leads
leads, leads
bulk
pcs.
pcs.
pcs.
2000
F (mm) d (mm)
3.5
2.5
5
7.5
1000
675
675
500
300
1)
225
1)
180
1)
150
1)
150
1)
200
200
120
200
200
200
120
250
250
344
344
120
001
002
003
004
012
8
5...6.3
5...12.5
16...18
Available upon request
Please read Cautions and warnings and
Important notes at the end of this document.
Bent 90°
leads,
blister
pcs.
Page 19 of 24
B43896
Up to 125 °C
Overview of packing units and code numbers for case sizes 18 × 20 ... 25 × 40
PAPR
Case size
d×l
Taped,
Ammo pack
mm
Standard,
bulk
pcs.
pcs.
Kinked
leads,
bulk
pcs.
Cut
Crimped J leads
leads, leads
bulk
pcs.
pcs.
pcs.
Bent 90°
leads,
blister
pcs.
18 × 20
175
18 × 25
150
250
175
175
200
200
120
250
150
150
200
200
18 × 31.5
120
100
250
100
100
150
150
120
18 × 35
100
100
100
150
150
150
18 × 40
125
100
100
120
72
20 × 20
125
125
125
200
20 × 25
125
125
125
200
20 × 30
100
100
100
120
20 × 35
100
100
100
120
20 × 40
100
100
100
120
22 × 30
80
100
100
22 × 35
80
100
100
22 × 40
80
100
100
25 × 40
40
100
The last three
digits of the
complete
ordering code
state the lead
configuration
000
Code
007
008
009
001
002
Please read Cautions and warnings and
Important notes at the end of this document.
F (mm) d (mm)
2.5
5
7.5
4...6.3
6.3...12.5
16...18
Page 20 of 24
003
004
012
B43896
Up to 125 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended
application, but also with regard to health and environmental compatibility. They do not contain
any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide
(DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They
contain flame-retarding substances which will quickly extinguish any flame that may have been
ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce
operating electrolytes. However, in exceptional cases, such materials must be used in order to
achieve specific physical and electrical properties because no safe substitute materials are
currently known. However, the amount of dangerous materials used in our products has been
limited to an absolute minimum. Nevertheless, the following rules should be observed when
handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin.
If electrolyte does come into contact with the skin, wash the affected parts immediately with
running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If
symptoms persist, seek medical treatment.
Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be
well ventilated. Clothing that has been contaminated by electrolyte must be changed and
rinsed in water.
Please read Cautions and warnings and
Important notes at the end of this document.
Page 21 of 24
B43896
Up to 125 °C
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed
description can be found in the relevant sections of chapter "General technical information".
Topic
Safety information
Polarity
Make sure that polar capacitors are connected
with the right polarity.
Reverse voltage
Voltages polarity classes should be prevented by
connecting a diode.
Do not exceed the upper category temperatur.
Upper category
temperature
Maintenance
Mounting
position of screw
terminal capacitors
Mounting of
single-ended
capacitors
Robustness of
terminals
Soldering
Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
supply is turned off and carefully discharge the
electricity of the capacitors.
Do not apply any mechanical stress to the
capacitor terminals.
Do not mount the capacitor with the terminals
(safety vent) upside down.
Reference
Chapter "General
technical information"
1
"Basic construction of
aluminum electrolytic
capacitors"
3.1.6
"Reverse voltage"
7.2
"Maximum permissible
operating temperature"
10
"Maintenance"
11.1.
"Mounting positions of
capacitors with screw
terminals"
The internal structure of single-ended capacitors 11.4
might be damaged if excessive force is applied to "Mounting
the lead wires.
considerations for
Avoid any compressive, tensile or flexural stress. single-ended capacitors"
Do not move the capacitor after soldering to PC
board.
Do not pick up the PC board by the soldered
capacitor.
Do not insert the capacitor on the PC board with a
hole space different to the lead space specified.
The following maximum tightening torques must
11.3
not be exceeded when connecting screw
"Mounting torques"
terminals:
M5: 2 Nm
M6: 2.5 Nm
Do not exceed the specified time or temperature 11.5
limits during soldering.
"Soldering"
Please read Cautions and warnings and
Important notes at the end of this document.
Page 22 of 24
B43896
Up to 125 °C
Topic
Soldering,
cleaning agents
Passive
flammability
Active
flammability
Safety information
Reference
Chapter "General
technical information"
Do not allow halogenated hydrocarbons to come 11.6
into contact with aluminum electrolytic capacitors. "Cleaning agents"
Avoid external energy, such as fire or electricity.
8.1
"Passive flammability"
Avoid overload of the capacitors.
8.2
"Active flammability"
Breakdown strength Do not damage the insulating sleeve, especially
of insulating
when ring clips are used for mounting.
sleeves
Please read Cautions and warnings and
Important notes at the end of this document.
Page 23 of 24
Reference
Chapter "Capacitors
with screw terminals"
"Screw terminals accessories"
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application.
As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar
with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out
in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications
in which the malfunction or failure of a passive electronic component could endanger human
life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured
by means of suitable design of the customer application or other action taken by the customer
(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by
third parties in the event of malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as “hazardous”). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order. We also
reserve the right to discontinue production and delivery of products. Consequently, we
cannot guarantee that all products named in this publication will always be available.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association
(ZVEI).
7. The trade names EPCOS, EPCOS-JONES, BAOKE, Alu-X, CeraDiode, CSSP, MLSC,
PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K,
UltraCap, WindCap are trademarks registered or pending in Europe and in other countries.
Further information will be found on the Internet at www.epcos.com/trademarks.
Page 24 of 24
Similar pages