N Style Coaxial Connector N Series FEATURE Characteristic Impedance ・ N series is a thread coupling coaxial connector which is 50 Ω the most popular as a 7mm type 50 Ω impedance. ・ N series is available for various cable type. Frequency Range ・ It is incompatible to NC series(75 Ω impedance N DC to 3GHz Style connector). Lock Type Screw CONFORMING STANDARD JIS-C5411,MIL-PRF-39012 SPECIFICATIONS Characteristic Impedance 50 Ω Rated Volatge 500VAC(r.m.s.) Dielectric Withstanding Voltage 1,500V AC(r.m.s) / 1 minute Insulation Resistance 1,000M Ω min. at 500V DC Contact Resistance 3m Ω max. V.S.W.R. 1.3 max. (DC 〜 3GHz) Operating Temperature -55 〜 +85℃ ＊ The specifications are typical but may not apply to all connectors. Please check the specifications on each item with its drawing from us when you use. Also, the performance is diffrenet by using cable. MATERIAL/FINISH RoHS Compliant Compliant Item 151222 Material / Finish Shell Copper Alloy / Ni or Ag Plating Contact (Female) Copper Alloy / Ag or Au Plating Contact (Male) Copper Alloy /Ag or Au Plating Insulator PTFE Gasket Silicon Rubber ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp N Series Unit：mm ○ Straight Cable Plug Clamp Type Applicable Part Number N-P-3 Cable 3C-2V φA φ21 N-P-3-CF 3D-2V 3C-2V N-P-3-Ni-CF 3D-2V 3C-2V N-P-3-NiCAu-CF （L） 3D-2V 3C-2W N-P-3W-CF N-P-5 3D-2W 3C-2W φA φ21 N-P-3W-Ni-CF N-P-3 （L） （L） φ21 φA φA φ21 N-P-8-1 3D-2W 3C-2W N-P-3W-D1-CF 3D-2W 40% φA （L） Finish Assembly Outer Center Instruction Conductor Conductor 80％ ～ 6.2 44.6 Ag Ag 1 6.2 44.6 Ni Ag 1 6.2 44.6 Ni Au 1 7.2 44.6 Ag Ag 1 7.2 44.6 Ni Ag 1 Ni Au 1 40% 7.2 44.6 80％ ～ N-P-55U-CF RG-55/U 5.4 44.6 Ag Ag 1 N-P-55U-Ni-CF RG-55/U 5.4 44.6 Ni Ag 1 N-P-58U-CF RG-58/U 5.4 44.6 Ag Ag 1 N-P-58U-Ni-1-CF RG-58/U 5.4 44.6 Ni Ag 1 N-P-58U-NiCAu-CF RG-58/U 5.4 44.6 Ni Au 1 （38.0） φ21 φA φA （L） Applicable Part Number φ21 N-P-5 N-P-10 Cable 3.5D-FE N-SP-3.5DFE-CF N-P-10 φ21 φA （38.0） φ21 φA 44.0 Ag Ag 1 8.6 44.0 Ni Ag 1 9.1 45.0 Ag Ag 1 9.1 45.0 Ni Ag 1 9.1 45.0 Ni Au 1 5D-FB 8.1 44.0 Ni Ag 1 5D-SFA 8.6 41.5 Ni Au ー 11.2 44.0 Ag Ag 1 11.2 44.0 Ni Ag 1 11.25 38.0 Ag Ag 2 5C-2W 5C-2W 5D-2W N-P-5DFB-1-CF N-SP-5DSFA-CF 5C-2W 5D-2W RG-8/U RG-9/U RG-8/U N-P-8U-Ni-CF RG-9/U RG-8/U UG-21D/U-CF RG-9/U φ21 φA 8.6 5D-2W N-P-8U-CF （51.7） ー 5C-2V N-P-5W-NiCAu-CF 形状はN-P-5D2V-CR20の場合 Au 5D-2V N-P-5W-Ni-CF （L） Ni 5C-2V N-P-5W-CF Assmbly Outer Center Instruction Conductor Conductor 41.5 5D-2V N-P-5-Ni-CF φ21 φA （51.7） ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. （L） http://www.ddknet.co.jp 形状はN-P-5D2V-CR20の場合 2 Finish 6.2 3.5D-QEFA N-P-5-CF N-P-8-1 φA （L） N-P-3 N N-P-5 Series ○ Straight Plug Unit：mm φ21 （L） φA φ21 φA （L） Clamp Type N-P-5 φ21 φA Part Number φ21 （L） φA N-P-8-1 （L） N-P-8-1 φA （38.0） N-P-10 8D-2V N-P-8-1-Ni-CF 8D-2V 12.6 Ni Ag 4 N-P-8DFB-1-CF 8D-FB 11.8 Ni Ag 4 φ21 N-P-10-CF N-P-Ni-CF φ21 φA （51.7） φA 12.6 Finish Assembly Outer Center Instruction Conductor Conductor N-P-8-1-CF Part Number （51.7） Cable φA Ag Ag 4 φ21 φA N-P-10 φ21 （38.0） Applicable N-P-10DFB-1-CF Applicable Cable 10C-2V 10D-2V 10C-2V 10D2V 10D-FB φA Finish Assembly Outer Center Instruction Conductor Conductor 14.2 Ag Ag 4 14.2 Ni Ag 4 14.2 Ni Ag 4 形状はN-P-5D2V-CR20の場合 φ21 φA （L） （L） 形状はN-P-5D2V-CR20の場合 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 3 N Series Unit：mm ○ Right Angle Cable Plug Clamp Type ジャック N-LP-58U N-J-3 φ21 Applicable Part Number Cable N-LP-58U-CF N-LP-58U φA φ21 φA φA φA (L2) φ17.5 Ni Ag ー （L） Cable N-J-5 5D-2V (L2) N-LP-5-Ni-CF 5D-2V 8.6 （L） 53.0 36.6 Center Conductor Conductor 53.0 36.6 Ag ー Ni Ag ー φA φB φA （L） φB φA (34.9) (L2) N-J-10 φB φA （52.7） φB φA (34.9) （L） Part Number N-LP-8U-CF N-LP-8U-Ni-CF φB φA (34.9) （47.0） Applicable Finish Assembly Center Instruction Cable Conductor Conductor （52.7） RG-8U Ag Ag ー RG-9/U N-J-10 RG-8U RG-9/U Outer Ni Ag （52.7） （47.0） ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 4 Assembly Instruction Ag N-J-10 φ21 φ11.2 （L） 8.6 Finish N-J-8 （L） （L1）φ21 φ11.2 （46） φA （L1）(L2) Outer N-J-8 φ21 φA Applicable φB φA N-LP-5-CF φA N-J-8 Part Number φ21 φ11.2 φ17.5 ー φA φA (L2) (L2) φA φA φ17.5 φ21 N-LP-8U φ17.5 Ag （46） （47.0） φ17.5 52.9 36.6 Ag N-J-3 N-J-5 （L1） （L1） N-LP-8U 5.4 Conductor Conductor Assembly Instruction N-J-5 φ21 φ21 （L1） 52.9 36.6 Center ジャック （L1） N-LP-8U 5.4 Finish （46） （L1） N-LP-58U ジャック N-LP-58U-Ni-CFN-J-3 RG-58/U (L2) φA φ17.5 RG-58/U φA (L1)（L2）Outer ー N Series Unit：mm ○ Straight ジャック Cable Jack N-J-3 Clamp Type Part Number Applicable Cable φA ジャック N-J-3 N-J-5 （46） ジャック φA φA N-J-3 3C-2V N-J-3-CF 3D-2V 3C-2V N-J-3-Ni-CF 3D-2V Finish φA Outer Assembly Instruction Center Conductor Conductor 6.2 Ag Ag 2 6.2 Ni Ag 2 N-J-58U-CF RG-58/U 5.4 Ag Ag 2 N-J-58U-Ni-CF RG-58/U 5.4 Ni Ag 2 ジャック （L） （46） N-J-3 φA φA φB φA φA N-J-5 N-J-8 Part Number （46） （L） N-J-8 N-J-10 N-J-5 φB φA （L） （46） N-J-8 N-J-5-Ni-CF N-J-8U-CF N-J-8U-Ni-CF （L） （52.7） N-J-8 Part Number N-J-8-1-CF φB φA φB φA （L） N-J-8-1-Ni-CF UG-23D/U-CF N-J-10 φA 5D-2V 8.6 47.0 5D-2V 8.6 RG-8/U RG-9/U RG-8/U RG-9/U Finish (L) Outer Center Conductor Conductor Assembly Instruction Ag Ag 2 47.0 Ni Ag 2 11.2 47.0 Ag Ag 2 11.2 47.0 Ni Ag 2 （L） φB φA N-J-10 Cable N-J-5-CF （L） φB φA φA φA N-J-5 Applicable Applicable φA φB 8D-2V 12.7 19.1 41.2 8D-2V 12.7 19.1 11.2 19.0 Cable RG-8/U RG-9/U Finish (L) Outer Center Conductor Conductor Assembly Instruction Ag Ag 5 41.2 Ni Ag 5 40.0 Ag Ag 5 （L） （52.7） φB φA N-J-10 Part Number φB φA （52.7） （52.7） N-J-10-CF N-J-10-Ni-CF N-J-10DFB-1-CF Applicable Cable 10C-2V 10D-2V 10C-2V 10D-2V 10D-FB φA φB Outer Finish Center Conductor Conductor 14.2 22.2 Ag Ag 5 14.2 22.2 Ni Ag 5 14.2 22.2 Ni Ag 5 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 5 Assembly Instruction N Series Unit：mm ○ Straight Panel Cable Jack N-PJ-3取付参考寸法 +0.1 C φ17.5 φA Part Number C （46） 4-φ3.2 18.2 Ag Ag 3 5.4 16.6 18.2 Ni Ag 3 N-PJ-58U-CF RG-58/U 5.4 16.6 18.2 Ag Ag 3 0 N-PJ-58U-Ni-CF 4-φ3.2 RG-58/U 5.4 16.6 18.2 Ni Ag 3 +0.1 φ17.8 02 C +0.1 18.24±0.05 4-φ3.2 0 18.2 □25.4 +0.1 4-φ3.2 0 4-φ3.2 0 +0.1 0 φ15.0 Part Number 5D-2V C D 8.6 17.5 16.7 18.24 Ag Ag 3 8.6 17.5 16.7 18.24 Ni Ag 3 +0.1 +0.1 φ15.0 0 2 18.2 Panel Mounting Dimensions 18.7 18.2±0.05 □25.4 L +0.1 4-φ3.2 0 4-φA◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. 18.2 http://www.ddknet.co.jp +0.1 φ15.0 0 6 Assembly Outer Center Instruction Conductor Conductor B 4-φ3.2 0 18.2 18.24±0.05 Finish φA 18.24±0.05 18.24±0.05 +0.1 18.2±0.05 φ18.0 0 φ14.6 D □25.4 D □25.4 Cable ±0.05 18.25D-2V N-PJ-5-Ni-CF D □25.4 Applicable 5C-2V +0.1 N-PJ-5-CF φ18.0 0 4-φA 18.2 18.24±0.05 +0.1 4-φ3.2 0 +0.1 18.2 18.7 +0.1 φ15.0 0 +0.1 +0.1 18.2±0.05 C 18.2 -R取付け 16.6 RG-55/U 4-φA 4-φ3.2 C 2.0 18.24±0.05 18.2±0.05 +0.1 0 （47） 4-φ3.2 4-φA 5.4 N-PJ-55U-Ni-CF 18.2±0.05 D +0.1 4-φ3.2 0 L □25.4 3 C 18.2±0.05 D C φ14.6 φB φA C Ag □25.4 φA D □25.4 3 18.24±0.05 18.2±0.05 4-φ3.2 0 4-φ3.2 N-PJ-5取付け Ag 18.2±0.05 D +0.1 B Ag Ni φ17.8 0 +0.1 18.2 18.2 D Panel （47） Mounting Dimensions □25.4 φ18.0 0 16.7 16.7 +0.1 φ18.0 0 4-φ3.2 2.0 B 18.2±0.05 R取付け4-φ3.2 6.2 6.2 18.24±0.05 φ17.5 φA □25.4 φB φA C Assembly Outer Center Instruction Conductor Conductor C 4-φ3.2 C +0.1 φ17.8 0 3C-2V Finish B 3D-2V 18.2±0.05 N-PJ-55U-CF RG-55/U 18.2±0.05 C 2.0 18.2±0.05 N-PJ-5取付け N-PJ-3取付参考寸法 φA 18.2±0.05 φA +0.1 4-φ3.2 0 4-φ3.2 3D-2V N-PJ-3-Ni-CF □25.4 Cable 3C-2V +0.1 N-PJ-3-CF φ17.8 0 （46） Applicable 18.2±0.05 4-φ3.2 B 2.0 4-φ3.2 0 φ18.0 0 C （46） □25.4 （47） N 18.24 +0.1 D1 φB φA φ17.8 0 18.2±0.05 D □25.4 Series 18.24±0.05 Unit：mm ○ Receptacle Jack +0.1 N-R取付け 4-φ3.2 +0.1 4-φA φ14.6 D +0.1 φ18.0 0 （47） D □25.4 4-φ3.2 0 Part Number N-R-CF +0.1 φ15.0 0 N-R-Ni-CF 18.24±0.05 2 18.2 18.7 □25.4 L L 18.2±0.05 C 18.24±0.05 18.2 2.0 4-φ3.2 0 Finish Outer Center Conductor Conductor 29 Ag Ag φ 3.2 29 Ni Ag φ 3.2 N-R-NiCAu-CF 29 Ni Au φ 3.2 UG-58A/U-CF 18.2±0.05 29 Ag Ag φ 3.2 +0.1 4-φ3.2 0 18.2 □25.4 18.2±0.05 Panel Mounting Dimensions ○ Dust Cap 5/8-24UNEF-2B （φ3.5） Part Number (φ19.5) L +0.1 φ15.0 0 （60） Finish N-RC-5 Ni N-RC-5-D1 Ag （71） 5/8-24UNEF-2B Part Number N-RC-3-CF Finish Ni (φ19.3) 2 18.7 18.2±0.05 18.2 4-φA 11.1 ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 7 φA N Series Unit：mm ○ Assembly Instruction(1) Straight Cable Plug Parts Configulration Contact Nut Nut Washer Washer Gasket Washer Clamp Contact Gasket Washer Clamp ① Insulator Body Insulator Body ① L=The Cable length require for the single-ended cable assembly. L=L1-10 L1 Sheath ② L1 Sheath Nut Nut Washer Washer Outer Conductor Cut the sheath 15mm from the end of the cable and insert the clamp. Please be careful to not damage the outer 15mm Gasket Clamp Clamp Insulator Canter Conductor （Pre-soldering） Insulator Pick the outer conductor and turn down to the clamp equally. Canter Conductor （Pre-soldering） 3.5～4.0mm 3.5～4.0mm ④ conductor. 15mm Gasket Pick the outer conductor and turn down to the clamp equally. ③ ② Insert the nut, washer and gasket into the cable. Outer Conductor 5.0mm 3.5mm 3.5mm ③ Pick the outer conductor and turn down to the clamp. Cut the outer conductor along the clamp. Cut the insulator and center conductor as fig.3. Please be careful to not damage the center conductor. ④ Solder up the contact with the center conductor. 5.0mm Soldering Contact Soldering No gap Contact No gap Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. ⑤ Insert the ring and insulator as fig. 5. ● In case of the insulator which has directivity, ⑤ insert the insulator as below direction and fit the thinner side of the insulator into the inside Washer diameter of the washer. Insulator Washer Insulator Washer Insulator ⑥ Washer assembly into the body and screw ⑥ Insert the above Insulator up by wrench. Applicable Cable 3C-2V, 3D-2V, 3C-2W,3D-2W, RG-55/U, RG-58/U 5C-2V, 5D-2V 5C-2W, 5D-2W 5D-FB RG-8/U, RG-9/U Recommended Tightening Torque 196 〜 392N・cm(20 〜 40kgf・cm) 392N・cm(40kgf・cm) 490 〜 686N・cm(50 〜 70kgf・cm) 441 〜 539N・cm(45 〜 55kgf・cm) 343 〜 392N・cm(35 〜 40kgf・cm) ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 8 N Series Unit：mm ○ Assembly Instruction(2) Straight Cable Jack Washer Clamp Washer Parts Configulration Contact Gasket Nut ① Body Insulator Contact Gasket Nut Washer Clamp Washer Body Insulator ① L=The Cable length require for the single-ended cable assembly. L1 L=L1-12 L1 Gasket Nut Outer Conductor Nut ② Cable Gasket Washer Cable ② Insert the nut, washer and gasket into the cable. Outer Conductor Cut the sheath 15mm from the end of the cable and insert the calmp. Please be careful to not damage the outer conductor . 15mm 15mm Washer Center Conductor Insulator ③ Pick the outer conductor and turn down to the （Pre-soldering） ③ Insulator Center Conductor （Pre-soldering） Clamp 3.5～4mm Cut the insulator and center conductor as fig.3. Please be careful to not damage the center conductor. 3.5mm Clamp 3.5～4mm 5mm 3.5mm ④ clamp. Cut the outer conductor along the clamp. ④ Solder up the contact with the center conductor. 5mm Contact Soldering Soldering Contact No gap Washer No gap ⑤ Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. ⑤ Insert the ring and insulator as fig. 5. Washer ● In case of the insulator which has directivity, insert the insulator as below direction and fit the thinner side of the insulator into the inside diameter of the washer. Insulator Insulator Washer Insulator ⑥ into the body and screw Washer ⑥ Insert the above assembly up by wrench. Applicable Cable 3C-2V, 3D-2V, RG-58/U, 5D-2V RG-8/U,RG-9/U Insulator Recommended Tightening Torque 196 〜 392N・cm(20 〜 40kgf・cm) 490 〜 686N・cm(50 〜 70kgf・cm) 343 〜 392N・cm(35 〜 40kgf・cm) ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 9 N Series Unit：mm ○ Assmbly Instruction(3）Straight Panel Jack Parts Configulration Washer Clamp Washer Body Washer Clamp Washer Body Nut Gasket Contact Insulator Nut Gasket Contact Insulator ① L2 Nut L2 Nut ② ① L=The Cable length require for the single-ended L1 cable assembly. Gasket L1 Outer Conductor Gasket Outer Conductor L=L1-6.7 L=-L2-1.2 ② Insert the nut, washer and gasket into the cable. Cut the sheath 15mm from the end of the cable 15mm and insert the clamp. Cable Washer Cable 15mm Insulator Center Conductor Washer （Pre-soldering) ③ Please be careful to not damage the outer Insulator Center Conductor （Pre-soldering) Clamp 3.5～4mm Clamp 3.5～4mm Soldering 3.5mm Contact 5mm Soldering Contact conductor. ④ Solder up the contact with the center conductor. Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. Washer Washer ⑤ clamp. Cut the outer conductor along the clamp. Please be careful to not damage the center No gap No gap ③ Pick the outer conductor and turn down to the Cut the insulator and center conductor as fig.3. 5mm 3.5mm ④ conductor. ⑤ Insert the ring and insulator as fig. 5. ● In case of the insulator which has directivity, insert the insulator as below direction and fit Insulator the thinner side of the insulator into the inside Washer diameter ofInsulator the washer. Insulator Washer Insulator ⑥ ⑥ Insert the above assembly into the body and screw up by wrench. Recommended Tightening Torque ：196 〜 392N・cm(20 〜 40kgf・cm) ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 10 N Series Unit：mm ○ Assembly Instruction(4）MIL Clamp Straigh Cable Plug Parts Configulration Nut Nut Gasket ※Washer Gasket ※Washer Clamp Body Clamp Contact Body Contact ※ As for N-P-8-1-CF, N-P-8-1-Ni-CF, UG-21D/U-CF and N-P-8DFB-1-CF washer is not attached. The washer is not inserted into the cable. ① The cable length require for the single-ended cable assembly as following table. ① Part Number L1 Sheath Sheath L1 Outer Conductor Washer N-P-8-1-Ni-CF N-P-10-Ni-CF L1ー21.5 N-P-8DFB-1-CF L1-14.2 N-P-10DFB-1-CF L2 Nut Nut ③ 10 N-P-10-CF ② Gasket L2 13 ② Insert the nut, washer and gasket into the cable. Clamp Cut the sheath from the end of the cable and insert the clamp. Clamp Gasket L2(mm) L1ー11.4 UG-21D/U-CF Outer Conductor Washer L（mm） N-P-8-1-CF Please be careful to not damage the outer conductor. Tip the outer conductor and turn down to the clamp equally. Insulator ③ Pick the outer conductor and turn down to the Tip the outer conductor and turn down to the clamp equally. Insulator clamp. Cut the outer conductor along the clamp. Center Conductor （Pre-soldering） Center Conductor （Pre-soldering） B B ④ A A Cut the insulator and center conductor as fig.3. Please be careful to not damage the center conductor. C Part Number C N-P-8-1-CF N-P-8-1-Ni-CF UG-21D/U-CF Soldering N-P-10-CF Soldering Contact No gap B（mm） 1.0 3.5 〜 4.0 C(mm) 5 N-P-10-Ni-CF 1.8 4.0 〜 4.5 N-P-8DFB-1-CF 1.8 3.5 〜 4.0 N-P-10DFB-1-CF Contact A（mm） 4.5 ④ Solder up the contact with the center conductor. No gap Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. ⑤ ⑤ Insert the above assembly into the body and screw up by wrench. Applicable Cable RG-8/U, RG-9/U 8D-2V 8D-FB 10C-2V, 10D-2V 10D-FB Recommended Tightening Torque 196 〜 392N・cm(20 〜 40kgf・cm) 294 〜 392N・cm(30 〜 40kgf・cm) 294N・cm(30kgf・cm) 980N・cm(100kgf・cm) 294N・cm(30kgf・cm) ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 11 N Series Unit：mm ○ Assembly Instruction(5）MIL Clamp Straight Cable Jack Parts Configulration ※Washer Nut ※Washer Nut Calmp Gasket Body ※ As for N-J-8-1-CF, N-J-8-1-Ni-CF and UG-23D/U-CF, Body the washer is not attached. The washer is not inserted into the cable. Calmp Gasket Contact Contact ① The cable length require for the single-ended ① cable assembly as following table. L1 Part Number L1 Sheath ② Washer Sheath Washer ③ N-J-8-1-Ni-CF Outer conductor Insert the nut, washer and gasket into the cable. ② Clamp Cut the sheath 10mm from the end of the cable Please be careful to not damage the outer Insulator conductor. Insulator ③ （Pre-soldering） Pick Outer Conductor 5mm B the outer conductor and turn down to the clamp. Cut the outer conductor along the clamp. Cut the insulator and center conductor as fig.3. （Pre-soldering） Please be careful to not damage the center A conductor. 5mm Part Number A Soldering N-J-8-1-CF N-J-8-1-Ni-CF UG-23D/U-CF Soldering Contact N-J-10-CF N-J-10-Ni-CF No gap N-J-10DFB-1-CF Contact No gap L1ー23.4 Outer Conductor Pick the outer conductor and turn down to the clamp equally/ ④ N-J-10-Ni-CF and insert the clamp. 10mm Clamp Gasket Pick the outer conductor and turn down to the clamp equally/ B L1ー13.2 L1ー13.8 N-J-10DFB-1-CF 10mm Gasket L（mm） UG-23D/U-CF N-J-10-CF Outer conductor Nut Nut N-J-8-1-CF A（mm） B（mm） 1.0 3.5 〜 4.0 1.8 4.0 〜 4.5 ④ Solder up the contact with the center conductor. Please be careful to not deform the insulator by heat. When the solder is stick out, please shave the extra solder. No gap between contact and insulator of the cable. ⑤ ⑤ Insert the above assembly into the body and screw up by wrench. Applicable Cable 8D-2V, RG-8/U, RG-9/U 10C-2V, 10D-2V 10D-FB Recommended Tightening Torque 294 〜 392N・cm(30 〜 40kgf・cm) 980N・cm(100kgf・cm) 294N・cm(30kgf・cm) ◎ Please acknowledge that the specification etc. of this catalog might change by the improvement etc. without notice. Moreover, the characteristic and the specification of the published product are the reference values. Please confirm the content with the latest delivery specifications when you use the product. http://www.ddknet.co.jp 12