OCXOW Oven Controlled Crystal Oscillator HC-MOS Output 3.3 V Power Supply FREQUENCY STABILITY OVER: OPERATING TEMP. RANGE : LONG TERM AGING 1ST YEAR: 10 YEARS: SUPPLY VOLTAGE ± 0.15 V LOAD ±10%: NOTE 1 see note 1 < ± 0.7 ppm * < ± 4.0 ppm * < ± 0.1 ppm * < ± 0.01 ppm POWER SUPPLY SUPPLY INPUT: INPUT CURRENT : INPUT CURRENT : Vcc = 3.3 V ±0.15 V * < 100 mA @ +30 °C * < 160 mA @ -20 °C * FREQUENCY CONTROL RANGE CONTROL VOLTAGE: FREQUENCY DEVIATION: RESPONSE SLOPE: see note 2 > ± 4 ppm * positive RISE AND FALL TIME: LEVEL „0“ AND „1“: FAN OUT (LOAD): TEMP. RANGE * STABILITY * OCXOW-BR1, BV3 -20 to +70 °C ±0.3 ppm (0.6 ppm peak to peak) TEMP. RANGE * STABILITY * OCXOW-CR1, CV3 -40 to +85 °C ±0.5 ppm (1ppm peak to peak) OCXOW-AR1, BR1, CR1 HC-MOS compatible 40 (min.) /60 (max.) % @ Vcc / 2 * tr < 7ns tf < 7 ns * < 0.4 V > Vcc –0.5 V 10 LS 0 to 10 kΩ > -4.7 kΩ OCXOW-AV3, BV3, CV3 -40 to +85 °C -65 to +125 °C 10 to 2000 Hz / 10 g 2000 g, 0.3 ms, ½ sine DIL 14, 4 pins, GND to case 8 mm (see packaging info) WARM-UP within spec after 60s @ 0°C * < 250 mA during 30s ∆ F/F: CURRENT: OCXOW-AR1, AV3 0 to +60 °C ±0.2 ppm (0.4 ppm peak to peak) ADJUSTMENT WITH RESISTOR (connected to ground) INPUT IMPEDANCE ENVIRONMENT OPERABLE TEMP. RANGE: STORAGE TEMP. RANGE: VIBRATION: SHOCK: PACKAGE: PACKAGE HEIGHT: TEMP. RANGE * STABILITY * NOTE 2 OUTPUT OUTPUT SIGNAL: SYMMETRY: up to 20 MHz ADJUSTMENT WITH VOLTAGE 0 to 3.3 V INPUT IMPEDANCE > 47 kΩ MARKING EXAMPLE OCXOW-BV3 20.000 MHz Type Frequency (PIN 1) 01.25 12 Spec No. Date Code Piece No. ORDERING INFORMATION EXAMPLE O C X O W - B V 3 20 MHz xxx MISCELLANEOUS SHORT TERM STABILITY: PHASE NOISE (BW = 1Hz): (typical, @ 10MHz in static conditions) * < 5 E-10 0.1 s to 30 s Typical 5 E-11 @ 1 s 1 Hz : - 70 dBc / Hz 10 Hz : -100 dBc / Hz 100 Hz : -130 dBc / Hz 1 kHz : -140 dBc / Hz Oscillator Type OCXO = oven controlled Crystal Oscillator N° of customer spec. Oscillator Version W = low power voltage 3.3V Temperature Range A = 0 to +60°C; +/-0.2ppm B = -20 to +70°C: +/-0.3ppm X = custom spec. Customer’s specification on request Oscillator output frequency Frequency Adjustment R1 = external resistor V3 = voltage 3.3V Y = custom spec. STANDARD FREQUENCIES (MHz) 10.0000 DATE: 12.8000 16.0000 16.3840 19.4400 20.0000 June 2003 Revision No.: 8 Page 1/2 In accordance with our policy of continuous development and improvement, we reserve the right to modify the design or the specifications of our products without prior notice. Headquarters: Micro Crystal Div. of ETA SA Mühlestrasse 14 CH-2540 Grenchen Switzerland Tel. Fax Internet Email +41 32 655 82 82 +41 32 655 80 90 www.microcrystal.ch [email protected] OCXOW Oven Controlled Crystal Oscillator HC-MOS Output 3.3 V Power Supply up to 20 MHz Application and Test Circuit: Adjustment with voltage Adjustment with resistor HC-MOS TTL Oscilloscope or Counter HC-MOS Vcc TTL Oscilloscope or Counter R load 2k A R load 2k A D1 14 8 1 7 D1 14 8 1 7 D2 Vcc Vcc V Cd2 Cd1 C load * 15pF D2 Vcc D3 V Cd2 Cd1 Radj (0–10kohms ) Vc D4 V C load * 15pF D3 D4 low thermal coefficient Waveform Output: Waveshape TTL tf Waveshape HC-MOS tf tr tr Vcc Vcc Vcc - 0.5V min. (Except 12V: 5V-0.5V min.) 2.4V min. 1/2 Vcc 1.4V Gnd + 0.4V max. Gnd T1 0.4V max. T2 Gnd T1 T2 Duty Cycle = 100 × DATE: T1 [%] T1 + T 2 June 2003 Revision No.: 6 Page 2/2 In accordance with our policy of continuous development and improvement, we reserve the right to modify the design or the specifications of our products without prior notice. Headquarters: Micro Crystal Div. of ETA SA Mühlestrasse 14 CH-2540 Grenchen Switzerland Tel. Fax Internet Email +41 32 655 82 82 +41 32 655 80 90 www.microcrystal.ch [email protected]