DOS(H)10-12T SERIES POINT OF LOAD DC-DC CONVERTER FEATURES • OUTPUT CURRENT UP TO 10A • SMALL SIZE AND LOW PROFILE : 1.30” X 0.53” X 0.30” (SMD) ; 2.00” X 0.50” X 0.28” (SIP) • HIGH EFFICIENCY UP TO 93% @ 3.3V FULL LOAD • INPUT RANGE FROM 8.3VDC TO 14.0VDC • FIXED SWITCHING FREQUENCY (300kHZ) • SMD & SIP PACKAGES • SMD PACKAGE QUALIFIED FOR LEADFREE REFLOW SOLDER PROCESS ACCORDING IPC J-STD-020D • OUTPUT VOLTAGE PROGRAMMABLE FROM 0.75VDC TO 5.0VDC VIA EXTERNAL RESISTOR • INPUT UNDER-VOLTAGE PROTECTION • SAFETY MEETS UL60950-1, EN60950-1 AND IEC60950-1 • ISO9001 CERTIFIED MANUFACTURING FACILITIES • COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU APPLICATIONS Wireless Network Telecom/Datacom Industry Control System Distributed Power Architectures Semiconductor Equipment Microprocessor Power Applications OPTIONS POSITIVE LOGIC REMOTE ON/OFF DESCRIPTION DOS10-12T (SMD type), DOH10-12T (for Vertical Mounting SIP type) and DOH10-12TA (for Horizontal Mounting SIP type) are non-isolated DC/DC converters that can deliver up to 10A of output current with full load efficiency of 93% at 3.3V output. T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted INPUT SPECIFICATIONS OUTPUT SPECIFICATIONS ≦3.63 >3.63 Output current Voltage accuracy Minimum load Line regulation Load regulation Vin=Vin(min) to Vin(max) at Full Load No Load to Full Load Ripple and noise (Note2) 20MHz bandwidth 10A max Vout(set) V 8.3 ~14VDC Input voltage range Vin(nom) =12V 8.3 ~13.2VDC Vout(set) V ± 2%Vout(set) 7A 0% Maximum input current Vin=8.3 to 14.0VDC; Io=Io(max) Input filter (Note 5) C filter ± 0.3%Vout(set) Input no load current Vout(set) =0.75VDC 40mA (Vin=12V, Io=0, module enabled) 100mA Vout(set) =5.0VDC ± 0.4%Vout(set) Start-up voltage 7.9VDC 30mVrms,max Input under voltage lockout 7.8VDC Shutdown voltage 75mVp-p,max Input reflected ripple current 5~20MHz, 1µH source impedance 20mAp-p 0.4% ± Temperature coefficient Io / t = 2.5A/µs ,Vin(nom) Peak deviation 200mV Dynamic load Setting time Load change step response (50% to 100% or (Vout<10%peak 25µs (Note 2) 100% to 50% of Io(max)) deviation) Io / t = 2.5A/µs,Vin(nom) Peak deviation 100mV Dynamic load Load change step Setting time response (50% to 100% or (Vout<10%peak 25µs (Note 3) 100% to 50% of Io(max)) deviation) Output current limit 200% Output short-circuit current Continuous, automatics recovery ESR 1m 1000µF,max External load capacitance 5000µF,max ESR 10m Vin=Vin(min) to Vin(max) Output voltage overshoot-startup 1%Vout(set) F.L. Voltage adjustability (see fig.1) (Note 4) 0.7525V ~ 5.0V Δ Δ Δ Δ ≧ Ω ≧ Ω ENVIRONMENTAL SPECIFICATIONS Operating ambient temperature Storage temperature range Thermal shock Vibration Relative humidity(non-condensing) Lead-free reflow solder process Moisture sensitivity level(MSL) Over temperature protection –40ºC ~ +85ºC(with derating) –55ºC ~ +125ºC MIL-STD-810F MIL-STD-810F 5% to 95% RH IPC J-STD-020D IPC J-STD-033B Level 2a 125ºC FEATURE SPECIFICATIONS Remote ON/OFF(Note 6) Negative logic(standard) ON = Open or 0V < Vr < 0.3V IIN=10µA,max OFF =2.5V < Vr < Vin(max) IIN=1mA,max Positive logic(option) ON = Open or (Vin-4) < Vr < Vin(max) IIN=10µA,max OFF=0V < Vr < 0.3V IIN=1mA,max GENERAL SPECIFICATIONS 10µA~1.0m Input current of Remote control pin Efficiency See table A Isolation voltage None Remote off state input current Nominal Input 2.0mA 0.5V,max Switching frequency 300kHz±10% Remote sense range Design meets safety standard IEC60950-1, UL60950-1, EN60950-1 Rise time Time for Vout to rise from 10% to 90%of Vout(set) 6ms,max. SMD 1.30 X 0.53 X 0.30 Inch Case 1 (Note 7) 3ms (33.0 X 13.5 X 7.7 mm) Turn-on delay time 3ms Case 2 (Note 8) Dimensions 2.00 X 0.50 X 0.28 Inch SIP (50.8 X 12.7 X 7.2 mm) Weight MTBF (Note 1) Page 1 of 3 BELLCORE TR-NWT-000332 MIL-HDBK-217F 6.0g(0.22oz) 1.409 x 107 hrs 1.048 x 106 hrs www.pduke.com 2013/5/3 DOS(H)10-12T SERIES POINT OF LOAD ON/OFF Logic Model Name DOS10-12T DOS10-12T-P DOH10-12T DOH10-12T-P DOH10-12TA DOH10-12TA-P Package Negative Positive Negative Positive Negative Positive DC-DC CONVERTER Input Voltage Output Voltage ≦ SMD Output Current Efficiency (%) Min. Load Max. Load 12Vin, 3.3VDC@10A 0A 10A 93% Vout(set) 3.63V Vin = 8.3-14VDC Vertical Mounting SIP Vout(set) 3.63V Horizontal Mounting Vin = 8.3-13.2VDC SIP ＞ 0.75 ~ 5.0VDC Note 1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC. MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load(Ground, Benign, controlled environment). 2. External with Cout = 1µF ceramic//10µF tantalum capacitors. 3. External with Cout = 2pcs of 150µF polymer capacitors. 4. Output voltage programmable from 0.7525V to 5V by connecting a single resistor (shown as Rtrim in Table 1) between the TRIM and GND pins of the module.To calculate the value of the resistor Rtrim for a particular output voltage Vout, use the following equation: 10500 Rtrim = - 1000 Ω Vout - 0.7525 5. It’s necessary to equip the external input capacitors at the input of the module. The capacitors should connect as close as possible to the input terminals that ensuring module stability. The external Cin is 4pcs of 47µF ceramic capacitors at least. 6. Device code with suffix “-P” – Positive logic(ON/OFF is open collector/drain logic input; Signal referenced to GND ) Device code with no suffix – Negative logic (ON/OFF pin is open collector/drain logic input with external pull –up resistor; signal referenced to GND) 7. Case 1 :On/Off input is set to logic low (module on) and then input power is applied (delay from instant at which Vin=Vin(min) until Vout=10% of Vout(set)) 8. Case 2 :Input power is applied for at least one second and then the ON/OFF input is set to logic low (delay form instant at which Von/off=0.3V until Vout=10% of Vout(set)) CAUTION: This power module is not internally fused. An input line fuse must always be used. DOS10-12T, Vo=3.3V, Derating Curve OUTPUT CURRENT,Io(A) 12 10 8 6 4 2 0 20 30 40 50 60 70 ℃ AMBIENT TEMPERATURE,TA( ) 80 90 Fig. 1 Table 1 Vout(set) (V) Rtrim (K Page 2 of 3 www.pduke.com Ω) 0.7525 Open 1.2 22.46 1.5 13.05 1.8 9.024 2.5 5.009 3.3 3.122 5 1.472 2013/5/3 DOS(H)10-12T SERIES POINT OF LOAD MECHANICAL DRAWING DC-DC CONVERTER ： DOH10-12T TYPE PIN CONNECTION PIN 1 2 3 4 5 6 7 8 10 11 DEFINE +OUTPUT +OUTPUT +SENSE +OUTPUT GND GND + INPUT + INPUT TRIM CTRL DOH10-12TA TYPE PIN CONNECTION PIN 1 2 3 4 5 6 7 8 10 11 DEFINE +OUTPUT +OUTPUT +SENSE +OUTPUT GND GND + INPUT + INPUT TRIM CTRL DOS10-12T TYPE PIN CONNECTION PIN 1 2 3 4 5 6 DEFINE CTRL +SENSE TRIM +OUTPUT GND + INPUT 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01 (0.25) 3. Pin dimension tolerance ±0.004 (0.1) Page 3 of 3 www.pduke.com 2013/5/3