(888) IPD-CONVerters ● (888) 473-2668 ● www.ipdconverters.com HBS SERIES - 50 WATT DESCRIPTION FEATURES HBS DC/DC converters provide up to 50 Watts of • Industry Standard Halfoutput power in an industry standard half-brick footprint. Brick The HBS units feature excellent efficiency, Class A • Open-Frame Packaging conducted noise specs, and fixed switching frequency. The HBS, using open-frame packaging, along with planar • 100°C Baseplate Operation magnetics provides maximum useable power with minimal thermal constraints. The HBS series is especially suited to telecom, networking, and industrial applications. • • • • Water Washable “True-Trim” Option 1500V Isolation Positive Or Negative Logic Efficiency vs. Load (24V Input) 95 TECHNICAL SPECIFICATIONS Input Voltage Range 24 VDC Nominal 48 VDC Nominal Reflected Ripple Input Reverse Voltage Protection 18 - 36 VDC 34 - 75 VDC 25 mA Shunt Diode EFFICIENCY % 90 75 HBS050YG-A HBS050YH-A HBS050YJ-A 65 60 10 30 40 50 60 70 80 90 100 90 100 Efficiency vs. Load (48V Input) 95 90 EFFICIENCY % ±1% ±0.2% Vout ±0.2% V out 0.5 VDC 10%, Iout Rated 25% Iout 4% Vout 500 µs ±10% Hiccup 110 - 140% 115 - 140% Vout Nom. Hiccup 20 LOAD % 85 80 HBS050ZG-A 75 HBS050ZH-A HBS050Z10.5-A 70 65 General Turn-On Time Remote Shutdown Remote Shutdown Reference Switching Frequency Isolation Input - Output Input - Case Output - Case Temperature Coefficient Case Temperature Operating Range Storage Range Thermal Shutdown Range Vibration, 3 Axes, 5 Min Each MTBF† (Bellcore TR-NWT-000332) Safety Weight (approx.) 80 70 Output Setpoint Accuracy Line Regulation Vin Min. - Vin Max., Iout Rated Load Regulation Iout Min. - Iout Max., Vin Nom. Remote Sense Headroom Minimum Output Current Dynamic Regulation, Loadstep Pk Deviation Settling Time Voltage Trim Range Short Circuit / Overcurrent Protection Current Limit Threshold Range, % of Iout Rated OVP Trip Range OVP 85 60 10 ms Positive or Negative Logic Vin Negative 500 kHz 1500 VDC 1050 VDC 500 VDC 0.2%/°C -40 to +100°C -40 to +125°C 105 to 115°C 5 g, 10 - 55 Hz 2.1 x 106 hrs UL, CUL 2.5 oz 1 10 20 30 40 50 60 70 80 LOAD % Notes † MTBF predictions may vary slightly from model to model. Specifications typically at 25°C, normal line, and full load, unless otherwise stated. Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment. Safety: Agency approvals may vary from model to model. Please consult factory for specific model information. Units are water-washable and fully compatible with commercial spray or immersion post wave-solder washing equipment. HBS SERIES - 50 WATT MODELS - (See the last page of this file for options.) Vin (Volts) Vin Range (Volts) Iin Max.* (Amps) Vout (Volts) Iout Rated (Amps) Ripple & Noise Pk-Pk (mV) Efficiency Typ. ** Model 24 24 24 24 24 48 48 48 48 48 18 - 36 18 - 36 18 - 36 18 - 36 18 - 36 34 - 75 34 - 75 34 - 75 34 - 75 34 - 75 3.50 2.30 3.60 3.50 3.50 1.32 1.22 1.80 1.75 1.75 3.30 3.30 5.00 12.00 15.00 3.30 3.30 5.00 12.00 15.00 15.00 10.00 10.00 4.20 3.30 15.00 10.00 10.00 4.20 3.30 100 100 100 150 150 100 100 100 150 150 80% 80% 84% 85% 86% 80% 80% 82% 85% 87% HBS050YE-A HBS033YE-A HBS050YG-A HBS050YH-A HBS050YJ-A HBS050ZE-A HBS033ZE-A † HBS050ZG-A HBS050ZH-A HBS050ZJ-A † † Denotes advanced product release. Consult factory for product availability. * Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output. MECHANICAL DRAWING 0.18" 2.28" (57.9mm) 1 5 1.400"(35.6mm) 2 6 1.000"(25.4mm) 7 0.700"(17.8mm) 3 8 0.400"(10.2mm) 4 9 DIA 0.080" (2.0mm) (61.0mm) HBS 2PL BOTTOM VIEW 2.40" (4.6mm) MOUNTING INSERTS M3X.5 THROUGH 4PL DIA 0.040" (1.0mm) 7PL 0 -0.50"(-12.7mm) 0.025" REF. 0 1.900" (0.6mm) (48.3mm) 0.50" (12.7mm) -0.19" (-4.8mm) Thermal Impedance Natural Convection 100 LFM 200 LFM 300 LFM 400 LFM 6.6 5.7 4.2 3.1 2.6 °C/W °C/W °C/W °C/W °C/W Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application. Pin Function 1 2 3 4 5 6 7 8 9 -Vin Case On/Off +Vin -V out -Sense Trim +Sense +V out 2 Tolerances Inches: .XX ± 0.020 .XXX ± 0.010 (Millimeters) .X ± 0.5 .XX ± 0.25 Pin: ± 0.002 ± 0.05 ( Dimensions as listed unless otherwise specified.) OPTIONS When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table. OPTION SUFFIX APPLICABLE SERIES Negative Logic N HAS, HBD, HBS, HES, LES, QBS, QES, TES, TQD Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS REMARKS TTL “Low” Turns Module ON TTL “High” Turns Module OFF XWS, XWD, XWT Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS PIN LENGTH AND HEATSINK OPTIONS Standard Pin Length is 0.180” (4.6mm) 0.110” (2.8mm) Pin Length 8 All Units (Except SMS) 0.150” (3.8mm) Pin Length 9 All Units (Except SMS) 0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Horizontal Heatsink 2H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Horizontal Heatsink 3H All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad 0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM Packages) Includes Thermal Pad Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and 0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length. NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc. TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. 3