MC33201, MC33202, MC33204, NCV33202, NCV33204 Low Voltage, Rail-to-Rail Operational Amplifiers http://onsemi.com The MC33201/2/4 family of operational amplifiers provide rail−to−rail operation on both the input and output. The inputs can be driven as high as 200 mV beyond the supply rails without phase reversal on the outputs, and the output can swing within 50 mV of each rail. This rail−to−rail operation enables the user to make full use of the supply voltage range available. It is designed to work at very low supply voltages (± 0.9 V) yet can operate with a supply of up to +12 V and ground. Output current boosting techniques provide a high output current capability while keeping the drain current of the amplifier to a minimum. Also, the combination of low noise and distortion with a high slew rate and drive capability make this an ideal amplifier for audio applications. PDIP−8 P, VP SUFFIX CASE 626 8 1 8 1 Features 8 • Low Voltage, Single Supply Operation • • • • • • • • • • 1 (+1.8 V and Ground to +12 V and Ground) Input Voltage Range Includes both Supply Rails Output Voltage Swings within 50 mV of both Rails No Phase Reversal on the Output for Over−driven Input Signals High Output Current (ISC = 80 mA, Typ) Low Supply Current (ID = 0.9 mA, Typ) 600 W Output Drive Capability Extended Operating Temperature Ranges (−40° to +105°C and −55° to +125°C) Typical Gain Bandwidth Product = 2.2 MHz NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable These are Pb−Free Devices SOIC−8 D, VD SUFFIX CASE 751 Micro8] DM SUFFIX CASE 846A PDIP−14 P, VP SUFFIX CASE 646 14 1 14 SOIC−14 D, VD SUFFIX CASE 751A 1 14 1 TSSOP−14 DTB SUFFIX CASE 948G ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 11 of this data sheet. © Semiconductor Components Industries, LLC, 2014 April, 2014 − Rev. 17 1 Publication Order Number: MC33201/D MC33201, MC33202, MC33204, NCV33202, NCV33204 PIN CONNECTIONS MC33204 All Case Styles MC33201 All Case Styles NC 1 8 2 7 Output 1 1 NC 2 VCC Inputs 1 Inputs 3 6 Output VEE 4 5 NC 1 4 3 12 11 5 10 6 2 3 Output 2 7 MC33202 All Case Styles Output 1 1 2 Inputs 1 1 3 VEE 4 13 VCC 4 Inputs 2 (Top View) 14 Output 4 9 8 Inputs 4 VEE Inputs 3 Output 3 (Top View) 8 VCC 7 Output 2 6 2 Inputs 2 5 (Top View) VCC VCC VEE VCC Vin- Vout VCC Vin+ VEE This device contains 70 active transistors (each amplifier). Figure 1. Circuit Schematic (Each Amplifier) http://onsemi.com 2 MC33201, MC33202, MC33204, NCV33202, NCV33204 MAXIMUM RATINGS Rating Symbol Value Unit VS +13 V Input Differential Voltage Range VIDR Note 1 V Common Mode Input Voltage Range (Note 2) VCM VCC + 0.5 V to VEE − 0.5 V V Output Short Circuit Duration ts Note 3 sec Maximum Junction Temperature TJ +150 °C Storage Temperature Tstg − 65 to +150 °C Maximum Power Dissipation PD Note 3 mW Supply Voltage (VCC to VEE) DC ELECTRICAL CHARACTERISTICS (TA = 25°C) Characteristic VCC = 2.0 V VCC = 3.3 V VCC = 5.0 V Input Offset Voltage VIO (max) MC33201 MC33202, NCV33202 MC33204, NCV33204 ± 8.0 ±10 ±12 ± 8.0 ±10 ±12 ± 6.0 ± 8.0 ±10 Output Voltage Swing VOH (RL = 10 kW) VOL (RL = 10 kW) 1.9 0.10 3.15 0.15 4.85 0.15 Power Supply Current per Amplifier (ID) 1.125 1.125 1.125 Unit mV Vmin Vmax mA Specifications at VCC = 3.3 V are guaranteed by the 2.0 V and 5.0 V tests. VEE = GND. DC ELECTRICAL CHARACTERISTICS (VCC = + 5.0 V, VEE = Ground, TA = 25°C, unless otherwise noted.) Figure Symbol Input Offset Voltage (VCM 0 V to 0.5 V, VCM 1.0 V to 5.0 V) MC33201: TA = + 25°C MC33201: TA = − 40° to +105°C MC33201V: TA = − 55° to +125°C MC33202/NCV33202: TA = + 25°C MC33202/NCV33202: TA = − 40° to +105°C MC33202V: TA = − 55° to +125°C NCV33202V: TA = − 55° to +125°C (Note 4) MC33204: TA = + 25°C MC33204: TA = − 40° to +105°C MC33204V: TA = − 55° to +125°C NCV33204: TA = − 55° to +125°C 3 ⎮VIO⎮ Input Offset Voltage Temperature Coefficient (RS = 50 W) TA = − 40° to +105°C TA = − 55° to +125°C 4 Characteristic Input Bias Current (VCM = 0 V to 0.5 V, VCM = 1.0 V to 5.0 V) TA = + 25°C TA = − 40° to +105°C TA = − 55° to +125°C 5, 6 Min Typ Max − − − − − − − − − − − − − − − − − − − − − − 6.0 9.0 13 8.0 11 14 14 10 13 17 17 − − 2.0 2.0 − − − − − 80 100 − 200 250 500 Unit mV DVIO/DT mV/°C ⎮IIB⎮ nA Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. The differential input voltage of each amplifier is limited by two internal parallel back−to−back diodes. For additional differential input voltage range, use current limiting resistors in series with the input pins. 2. The input common mode voltage range is limited by internal diodes connected from the inputs to both supply rails. Therefore, the voltage on either input must not exceed either supply rail by more than 500 mV. 3. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded. (See Figure 2) 4. All NCV devices are qualified for Automotive use. http://onsemi.com 3 MC33201, MC33202, MC33204, NCV33202, NCV33204 DC ELECTRICAL CHARACTERISTICS (cont.) (VCC = + 5.0 V, VEE = Ground, TA = 25°C, unless otherwise noted.) Figure Symbol Input Offset Current (VCM = 0 V to 0.5 V, VCM = 1.0 V to 5.0 V) TA = + 25°C TA = − 40° to +105°C TA = − 55° to +125°C − ⎮IIO⎮ Common Mode Input Voltage Range − VICR Large Signal Voltage Gain (VCC = + 5.0 V, VEE = − 5.0 V) RL = 10 kW RL = 600 W 7 AVOL Characteristic Output Voltage Swing (VID = ± 0.2 V) RL = 10 kW RL = 10 kW RL = 600 W RL = 600 W Min Typ Max − − − 5.0 10 − 50 100 200 VEE − VCC Unit nA V kV/V 50 25 300 250 − − VOH VOL VOH VOL 4.85 − 4.75 − 4.95 0.05 4.85 0.15 − 0.15 − 0.25 60 90 − 500 25 − 50 80 − − − 0.9 0.9 1.125 1.125 8, 9, 10 V Common Mode Rejection (Vin = 0 V to 5.0 V) 11 CMR Power Supply Rejection Ratio VCC/VEE = 5.0 V/GND to 3.0 V/GND 12 PSRR Output Short Circuit Current (Source and Sink) 13, 14 ISC Power Supply Current per Amplifier (VO = 0 V) TA = − 40° to +105°C TA = − 55° to +125°C 15 ID dB mV/V mA mA AC ELECTRICAL CHARACTERISTICS (VCC = + 5.0 V, VEE = Ground, TA = 25°C, unless otherwise noted.) Characteristic Slew Rate (VS = ± 2.5 V, VO = − 2.0 V to + 2.0 V, RL = 2.0 kW, AV = +1.0) Figure Symbol 16, 26 SR Min Typ Max 0.5 1.0 − Unit V/ms Gain Bandwidth Product (f = 100 kHz) 17 GBW − 2.2 − MHz Gain Margin (RL = 600 W, CL = 0 pF) 20, 21, 22 AM − 12 − dB Phase Margin (RL = 600 W, CL = 0 pF) 20, 21, 22 OM − 65 − Deg 23 CS − 90 − dB BWP − 28 − kHz − − 0.002 0.008 − − − 100 − Rin − 200 − kW Cin − 8.0 − pF − − 25 20 − − nV/ Hz − − 0.8 0.2 − − Channel Separation (f = 1.0 Hz to 20 kHz, AV = 100) Power Bandwidth (VO = 4.0 Vpp, RL = 600 W, THD ≤ 1 %) Total Harmonic Distortion (RL = 600 W, VO = 1.0 Vpp, AV = 1.0) f = 1.0 kHz f = 10 kHz 24 THD % ⎮ZO⎮ Open Loop Output Impedance (VO = 0 V, f = 2.0 MHz, AV = 10) Differential Input Resistance (VCM = 0 V) Differential Input Capacitance (VCM = 0 V) Equivalent Input Noise Voltage (RS = 100 W) f = 10 Hz f = 1.0 kHz 25 Equivalent Input Noise Current f = 10 Hz f = 1.0 kHz 25 http://onsemi.com 4 W en in pA/ Hz 2500 40 PERCENTAGE OF AMPLIFIERS (%) PD(max) , MAXIMUM POWER DISSIPATION (mW MC33201, MC33202, MC33204, NCV33202, NCV33204 8 and 14 Pin DIP Pkg 2000 TSSOP-14 Pkg 1500 SO-14 Pkg 1000 SOIC-8 Pkg 500 0 -55 -40 -25 0 25 50 85 TA, AMBIENT TEMPERATURE (°C) 30 25 20 15 10 5.0 0 -10 -8.0 -6.0 -4.0 -2.0 0 2.0 4.0 6.0 VIO, INPUT OFFSET VOLTAGE (mV) 125 Figure 2. Maximum Power Dissipation versus Temperature I IB , INPUT BIAS CURRENT (nA) 30 160 120 20 10 0 -50 -40 -30 -20 -10 0 10 20 30 40 VCC = +5.0 V VEE = Gnd VCM = 0 V to 0.5 V 80 VCM > 1.0 V 40 0 -55 -40 -25 50 TCV , INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (mV/°C) IO A VOL , OPEN LOOP VOLTAGE GAIN (kV/V) 100 50 0 -50 -100 VCC = 12 V VEE = Gnd TA = 25°C -200 0 2.0 4.0 6.0 8.0 10 VCM, INPUT COMMON MODE VOLTAGE (V) 25 70 85 125 Figure 5. Input Bias Current versus Temperature 150 -150 0 TA, AMBIENT TEMPERATURE (°C) Figure 4. Input Offset Voltage Temperature Coefficient Distribution I IB , INPUT BIAS CURRENT (nA) 10 200 360 amplifiers tested from 3 (MC33204) wafer lots VCC = +5.0 V VEE = Gnd TA = 25°C DIP Package 40 -250 8.0 Figure 3. Input Offset Voltage Distribution 50 PERCENTAGE OF AMPLIFIERS (%) 360 amplifiers tested from 3 (MC33204) wafer lots VCC = +5.0 V VEE = Gnd TA = 25°C DIP Package 35 12 300 260 220 180 140 VCC = +5.0 V VEE = Gnd RL = 600 W DVO = 0.5 V to 4.5 V 100 -55 -40 -25 Figure 6. Input Bias Current versus Common Mode Voltage 0 25 70 85 TA, AMBIENT TEMPERATURE (°C) 105 Figure 7. Open Loop Voltage Gain versus Temperature http://onsemi.com 5 125 MC33201, MC33202, MC33204, NCV33202, NCV33204 RL = 600 W TA = 25°C 10 8.0 6.0 4.0 2.0 0 ±1.0 VCC VSAT, OUTPUT SATURATION VOLTAGE (V) VO, OUTPUT VOLTAGE (Vpp ) 12 ±2.0 ±3.0 ±4.0 ±5.0 VCC,⎮VEE⎮ SUPPLY VOLTAGE (V) ±6.0 TA = -55°C TA = 125°C VCC - 0.4 V TA = -55°C CMR, COMMON MODE REJECTION (dB) VO, OUTPUT VOLTAGE (Vpp ) 6.0 VCC = +6.0 V VEE = -6.0 V RL = 600 W AV = +1.0 TA = 25°C 5.0 60 40 VCC = +6.0 V VEE = -6.0 V TA = -55° to +125°C 20 0 10 I SC , OUTPUT SHORT CIRCUIT CURRENT (mA) PSR, POWER SUPPLY REJECTION (dB) PSR+ 80 60 PSR40 VCC = +6.0 V VEE = -6.0 V TA = -55° to +125°C 0 1.0 k 10 k f, FREQUENCY (Hz) 100 1.0 k 10 k f, FREQUENCY (Hz) 100 k 1.0 M Figure 11. Common Mode Rejection versus Frequency 100 100 VEE 20 15 80 1.0 M 120 10 10 IL, LOAD CURRENT (mA) 100 Figure 10. Output Voltage versus Frequency 20 VEE + 0.2 V Figure 9. Output Saturation Voltage versus Load Current 9.0 10 k 100 k f, FREQUENCY (Hz) TA = 25°C TA = 125°C 0 12 0 1.0 k VEE + 0.4 V VCC = +5.0 V VEE = -5.0 V Figure 8. Output Voltage Swing versus Supply Voltage 3.0 VCC - 0.2 V TA = 25°C 100 k 1.0 M 100 Source 80 60 Sink 40 VCC = +6.0 V VEE = -6.0 V TA = 25°C 20 0 0 1.0 2.0 3.0 4.0 5.0 ⎮Vout⎮, OUTPUT VOLTAGE (V) Figure 12. Power Supply Rejection versus Frequency Figure 13. Output Short Circuit Current versus Output Voltage http://onsemi.com 6 6.0 I CC , SUPPLY CURRENT PER AMPLIFIER (mA) 150 125 VCC = +5.0 V VEE = Gnd 100 Source 75 Sink 50 25 0 -55 -40 -25 0 25 70 85 TA, AMBIENT TEMPERATURE (°C) 105 125 2.0 1.6 TA = 125°C 1.2 TA = 25°C 0.8 TA = -55°C 0.4 0 ±0 ±1.0 Figure 14. Output Short Circuit Current versus Temperature GBW, GAIN BANDWIDTH PRODUCT (MHz) +Slew Rate 1.0 -Slew Rate 0.5 25 70 85 105 0 -55 -40 -25 0 25 70 85 105 Figure 16. Slew Rate versus Temperature Figure 17. Gain Bandwidth Product versus Temperature 40 VS = ±6.0 V TA = 25°C RL = 600 W 80 30 120 1A 2A 10 A 1.0 TA, AMBIENT TEMPERATURE (°C) 50 -30 10 k 2.0 TA, AMBIENT TEMPERATURE (°C) 70 -10 VCC = +2.5 V VEE = -2.5 V f = 100 kHz 3.0 125 2B 1A - Phase, CL = 0 pF 1B - Gain, CL = 0 pF 2A - Phase, CL = 300 pF 2B - Gain, CL = 300 pF 100 k 1B 1.0 M 160 200 O , EXCESS PHASE (DEGREES) , OPEN LOOP VOLTAGE GAIN (dB) VOL 0 4.0 A VOL, OPEN LOOP VOLTAGE GAIN (dB) SR, SLEW RATE (V/μ s) VCC = +2.5 V VEE = -2.5 V VO = ±2.0 V 0 -55 -40 -25 ±6.0 Figure 15. Supply Current per Amplifier versus Supply Voltage with No Load 2.0 1.5 ±2.0 ±3.0 ±4.0 ±5.0 VCC, ⎮VEE⎮, SUPPLY VOLTAGE (V) 70 30 1A 10 120 -10 160 1A - Phase, VS = ±6.0 V 1B - Gain, VS = ±6.0 V 2A - Phase, VS = ±1.0 V 2B - Gain, VS = ±1.0 V f, FREQUENCY (Hz) 100 k 1B 2B 200 1.0 M f, FREQUENCY (Hz) Figure 18. Voltage Gain and Phase versus Frequency Figure 19. Voltage Gain and Phase versus Frequency http://onsemi.com 7 80 2A -30 10 k 240 10 M 40 CL = 0 pF TA = 25°C RL = 600 W 50 125 240 10 M O , EXCESS PHASE (DEGREES) I SC , OUTPUT SHORT CIRCUIT CURRENT (mA) MC33201, MC33202, MC33204, NCV33202, NCV33204 MC33201, MC33202, MC33204, NCV33202, NCV33204 75 50 50 40 30 VCC = +6.0 V VEE = -6.0 V RL = 600 W CL = 100 pF 40 30 20 20 10 10 Gain Margin 0 -55 -40 -25 0 25 70 85 105 O M , PHASE MARGIN (DEGREES) 60 A , GAIN MARGIN (dB) M O M , PHASE MARGIN (DEGREES) 60 60 60 VCC = +6.0 V VEE = -6.0 V TA = 25°C 45 30 15 0 0 125 10 100 Gain Margin 12 10 40 8.0 30 6.0 20 4.0 10 2.0 0 10 THD, TOTAL HARMONIC DISTORTION (%) 14 10 1.0 0 1.0 k 100 AV = 10 60 VCC = +6.0 V VEE = -6.0 V VO = 8.0 Vpp TA = 25°C 30 1.0 k 10 k f, FREQUENCY (Hz) Figure 22. Gain and Phase Margin versus Capacitive Load Figure 23. Channel Separation versus Frequency VCC = +5.0 V TA = 25°C VO = 2.0 Vpp VEE = -5.0 V RL = 600 W AV = 100 AV = 10 0.01 0.001 10 90 CL, CAPACITIVE LOAD (pF) AV = 1000 0.1 AV = 100 120 0 100 AV = 1.0 100 1.0 k 10 k 100 k en , EQUIVALENT INPUT NOISE VOLTAGE (nV/ Hz) 50 0 100 k 150 CS, CHANNEL SEPARATION (dB) 60 10 k Figure 21. Gain and Phase Margin versus Differential Source Resistance 16 Phase Margin 1.0 k RT, DIFFERENTIAL SOURCE RESISTANCE (W) A , GAIN MARGIN (dB) M O M , PHASE MARGIN (DEGREES) 70 15 Gain Margin Figure 20. Gain and Phase Margin versus Temperature VCC = +6.0 V VEE = -6.0 V RL = 600 W AV = 100 TA = 25°C 45 30 TA, AMBIENT TEMPERATURE (°C) 80 75 Phase Margin A , GAIN MARGIN (dB) M 70 Phase Margin 50 5.0 VCC = +6.0 V VEE = -6.0 V TA = 25°C 40 30 3.0 Noise Voltage 20 10 Noise Current 0 10 100 1.0 k 10 k f, FREQUENCY (Hz) Figure 25. Equivalent Input Noise Voltage and Current versus Frequency http://onsemi.com 8 2.0 1.0 f, FREQUENCY (Hz) Figure 24. Total Harmonic Distortion versus Frequency 4.0 0 100 k i n , INPUT REFERRED NOISE CURRENT (pA/ Hz) 70 MC33201, MC33202, MC33204, NCV33202, NCV33204 DETAILED OPERATING DESCRIPTION Circuit Information The MC33201/2/4 family of operational amplifiers are unique in their ability to swing rail−to−rail on both the input and the output with a completely bipolar design. This offers low noise, high output current capability and a wide common mode input voltage range even with low supply voltages. Operation is guaranteed over an extended temperature range and at supply voltages of 2.0 V, 3.3 V and 5.0 V and ground. Since the common mode input voltage range extends from VCC to VEE, it can be operated with either single or split voltage supplies. The MC33201/2/4 are guaranteed not to latch or phase reverse over the entire common mode range, however, the inputs should not be allowed to exceed maximum ratings. Rail−to−rail performance is achieved at the input of the amplifiers by using parallel NPN−PNP differential input stages. When the inputs are within 800 mV of the negative rail, the PNP stage is on. When the inputs are more than 800 mV greater than VEE, the NPN stage is on. This switching of input pairs will cause a reversal of input bias currents (see Figure 6). Also, slight differences in offset voltage may be noted between the NPN and PNP pairs. Cross−coupling techniques have been used to keep this change to a minimum. In addition to its rail−to−rail performance, the output stage is current boosted to provide 80 mA of output current, enabling the op amp to drive 600 W loads. Because of this high output current capability, care should be taken not to exceed the 150°C maximum junction temperature. VCC = +6.0 V VEE = -6.0 V RL = 600 W CL = 100 pF TA = 25°C VCC = +6.0 V VEE = -6.0 V RL = 600 W CL = 100 pF TA = 25°C V , OUTPUT VOLTAGE (50 mV/DIV) O V , OUTPUT VOLTAGE (2.0 mV/DIV) O General Information t, TIME (10 ms/DIV) t, TIME (5.0 ms/DIV) V , OUTPUT VOLTAGE (2.0 V/DIV) O Figure 26. Noninverting Amplifier Slew Rate Figure 27. Small Signal Transient Response VCC = +6.0 V VEE = -6.0 V RL = 600 W CL = 100 pF AV = 1.0 TA = 25°C t, TIME (10 ms/DIV) Figure 28. Large Signal Transient Response Surface mount board layout is a critical portion of the total design. The footprint for the semiconductor packages must be the correct size to ensure proper solder connection interface between the board and the package. With the correct pad geometry, the packages will self−align when subjected to a solder reflow process. http://onsemi.com 9 MC33201, MC33202, MC33204, NCV33202, NCV33204 ORDERING INFORMATION Operational Amplifier Function Device Operating Temperature Range MC33201DG MC33201DR2G MC33201PG TA= −40° to +105°C Single MC33201VDR2G MC33201VDG TA = −55° to 125°C Shipping† SOIC−8 (Pb−Free) 98 Units / Rail MC33202DR2G 2500 / Tape & Reel PDIP−8 (Pb−Free) 50 Units / Rail SOIC−8 (Pb−Free) 2500 / Tape & Reel SOIC−8 (Pb−Free) 98 Units / Rail SOIC−8 (Pb−Free) MC33202DG 98 Units / Rail 2500 / Tape & Reel Micro−8 (Pb−Free) 4000 / Tape & Reel MC33202PG PDIP−8 (Pb−Free) 50 Units / Rail MC33202VDG SOIC−8 (Pb−Free) 98 Units / Rail SOIC−8 (Pb−Free) 2500 / Tape & Reel MC33202VPG PDIP−8 (Pb−Free) 50 Units / Rail MC33204DG SO−14 (Pb−Free) MC33202DMR2G TA= −40 ° to +105°C NCV33202DMR2G* Dual MC33202VDR2G NCV33202VDR2G* TA = −55° to 125°C MC33204DR2G MC33204DTBG TA= −40 ° to +105°C MC33204DTBR2G Quad Package TSSOP−14 (Pb−Free) 55 Units / Rail 2500 Units / Tape & Reel 96 Units / Rail 2500 Units / Tape & Reel MC33204PG PDIP−14 (Pb−Free) 25 Units / Rail MC33204VDG SO−14 (Pb−Free) 55 Units / Rail MC33204VDR2G SO−14 (Pb−Free) 2500 Units / Tape & Reel NCV33204DTBR2G* TSSOP−14 (Pb−Free) 2500 Units / Tape & Reel MC33204VPG PDIP−14 (Pb−Free) 25 Units / Rail NCV33204DR2G* TA = −55° to 125°C †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable. http://onsemi.com 10 MC33201, MC33202, MC33204, NCV33202, NCV33204 MARKING DIAGRAMS 8 1 320xV ALYW G * Micro−8 DM SUFFIX CASE 846A 8 8 8 3320x ALYW G PDIP−8 VP SUFFIX CASE 626 PDIP−8 P SUFFIX CASE 626 SOIC−8 VD SUFFIX CASE 751 SOIC−8 D SUFFIX CASE 751 MC3320xP AWL YYWWG 8 MC33202VP AWL YYWWG 14 14 MC33204VDG AWLYWW 1 * PDIP−14 VP SUFFIX CASE 646 14 MC33204P AWLYYWWG 1 MC33204VP AWLYYWWG 1 MC33 204 ALYWG G 1 1 x = 1 or 2 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G = Pb−Free Package G = Pb−Free Package (Note: Microdot may be in either location) *This marking diagram applies to NCV3320xV **This marking diagram applies to NCV33202DMR2G 11 MC33204DG AWLYWW TSSOP−14 DTB SUFFIX CASE 948G 14 14 http://onsemi.com 14 1 1 PDIP−14 P SUFFIX CASE 646 SO−14 VD SUFFIX CASE 751A ** 3202 AYWG G 1 1 SO−14 D SUFFIX CASE 751A MC33 204V ALYWG G 1 * MC33201, MC33202, MC33204, NCV33202, NCV33204 PACKAGE DIMENSIONS PDIP−8 P, VP SUFFIX CASE 626−05 ISSUE N D A E H 8 5 1 4 E1 NOTE 8 c b2 B END VIEW TOP VIEW WITH LEADS CONSTRAINED NOTE 5 A2 A e/2 NOTE 3 L SEATING PLANE A1 C M D1 e 8X SIDE VIEW b 0.010 eB END VIEW M C A M B M NOTE 6 http://onsemi.com 12 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. DIMENSIONS A, A1 AND L ARE MEASURED WITH THE PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS−3. 4. DIMENSIONS D, D1 AND E1 DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS ARE NOT TO EXCEED 0.10 INCH. 5. DIMENSION E IS MEASURED AT A POINT 0.015 BELOW DATUM PLANE H WITH THE LEADS CONSTRAINED PERPENDICULAR TO DATUM C. 6. DIMENSION E3 IS MEASURED AT THE LEAD TIPS WITH THE LEADS UNCONSTRAINED. 7. DATUM PLANE H IS COINCIDENT WITH THE BOTTOM OF THE LEADS, WHERE THE LEADS EXIT THE BODY. 8. PACKAGE CONTOUR IS OPTIONAL (ROUNDED OR SQUARE CORNERS). DIM A A1 A2 b b2 C D D1 E E1 e eB L M INCHES MIN MAX −−−− 0.210 0.015 −−−− 0.115 0.195 0.014 0.022 0.060 TYP 0.008 0.014 0.355 0.400 0.005 −−−− 0.300 0.325 0.240 0.280 0.100 BSC −−−− 0.430 0.115 0.150 −−−− 10 ° MILLIMETERS MIN MAX −−− 5.33 0.38 −−− 2.92 4.95 0.35 0.56 1.52 TYP 0.20 0.36 9.02 10.16 0.13 −−− 7.62 8.26 6.10 7.11 2.54 BSC −−− 10.92 2.92 3.81 −−− 10 ° MC33201, MC33202, MC33204, NCV33202, NCV33204 PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE AK NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. −X− A 8 5 S B 0.25 (0.010) M Y M 1 4 K −Y− G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− 0.10 (0.004) H M D 0.25 (0.010) M Z Y S X J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 13 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC33201, MC33202, MC33204, NCV33202, NCV33204 PACKAGE DIMENSIONS Micro8 DM SUFFIX CASE 846A−02 ISSUE H NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. 846A-01 OBSOLETE, NEW STANDARD 846A-02. D HE PIN 1 ID E e b 8 PL 0.08 (0.003) −T− M T B S A MILLIMETERS NOM MAX −− 1.10 0.08 0.15 0.33 0.40 0.18 0.23 3.00 3.10 3.00 3.10 0.65 BSC 0.40 0.55 0.70 4.75 4.90 5.05 DIM A A1 b c D E e L HE S SEATING PLANE MIN −− 0.05 0.25 0.13 2.90 2.90 A 0.038 (0.0015) A1 L c SOLDERING FOOTPRINT* 8X 1.04 0.041 0.38 0.015 3.20 0.126 6X 8X 4.24 0.167 0.65 0.0256 5.28 0.208 SCALE 8:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 14 INCHES NOM −− 0.003 0.013 0.007 0.118 0.118 0.026 BSC 0.016 0.021 0.187 0.193 MIN −− 0.002 0.010 0.005 0.114 0.114 MAX 0.043 0.006 0.016 0.009 0.122 0.122 0.028 0.199 MC33201, MC33202, MC33204, NCV33202, NCV33204 PACKAGE DIMENSIONS PDIP−14 CASE 646−06 ISSUE R D 14 A 8 E H E1 1 NOTE 8 7 b2 c B TOP VIEW END VIEW WITH LEADS CONSTRAINED NOTE 5 A2 A NOTE 3 L SEATING PLANE A1 C M D1 eB END VIEW e 14X b SIDE VIEW 0.010 M C A M B M NOTE 6 http://onsemi.com 15 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: INCHES. 3. DIMENSIONS A, A1 AND L ARE MEASURED WITH THE PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS−3. 4. DIMENSIONS D, D1 AND E1 DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS ARE NOT TO EXCEED 0.10 INCH. 5. DIMENSION E IS MEASURED AT A POINT 0.015 BELOW DATUM PLANE H WITH THE LEADS CONSTRAINED PERPENDICULAR TO DATUM C. 6. DIMENSION E3 IS MEASURED AT THE LEAD TIPS WITH THE LEADS UNCONSTRAINED. 7. DATUM PLANE H IS COINCIDENT WITH THE BOTTOM OF THE LEADS, WHERE THE LEADS EXIT THE BODY. 8. PACKAGE CONTOUR IS OPTIONAL (ROUNDED OR SQUARE CORNERS). DIM A A1 A2 b b2 C D D1 E E1 e eB L M INCHES MIN MAX −−−− 0.210 0.015 −−−− 0.115 0.195 0.014 0.022 0.060 TYP 0.008 0.014 0.735 0.775 0.005 −−−− 0.300 0.325 0.240 0.280 0.100 BSC −−−− 0.430 0.115 0.150 −−−− 10 ° MILLIMETERS MIN MAX −−− 5.33 0.38 −−− 2.92 4.95 0.35 0.56 1.52 TYP 0.20 0.36 18.67 19.69 0.13 −−− 7.62 8.26 6.10 7.11 2.54 BSC −−− 10.92 2.92 3.81 −−− 10 ° MC33201, MC33202, MC33204, NCV33202, NCV33204 PACKAGE DIMENSIONS SOIC−14 CASE 751A−03 ISSUE K D A B 14 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE PROTRUSION SHALL BE 0.13 TOTAL IN EXCESS OF AT MAXIMUM MATERIAL CONDITION. 4. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSIONS. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 8 A3 E H L 1 0.25 M DETAIL A 7 B 13X M b 0.25 M C A S B S DETAIL A h A e DIM A A1 A3 b D E e H h L M X 45 _ M A1 C SEATING PLANE MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.19 0.25 0.35 0.49 8.55 8.75 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ SOLDERING FOOTPRINT* 6.50 14X 1.18 1 1.27 PITCH 14X 0.58 DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 16 INCHES MIN MAX 0.054 0.068 0.004 0.010 0.008 0.010 0.014 0.019 0.337 0.344 0.150 0.157 0.050 BSC 0.228 0.244 0.010 0.019 0.016 0.049 0_ 7_ MC33201, MC33202, MC33204, NCV33202, NCV33204 PACKAGE DIMENSIONS TSSOP−14 CASE 948G ISSUE B 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. S S N 2X 14 L/2 0.25 (0.010) 8 M B −U− L PIN 1 IDENT. F 7 1 0.15 (0.006) T U N S DETAIL E K A −V− ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ ÇÇÇ K1 J J1 SECTION N−N −W− C 0.10 (0.004) −T− SEATING PLANE D H G DETAIL E DIM A B C D F G H J J1 K K1 L M MILLIMETERS INCHES MIN MAX MIN MAX 4.90 5.10 0.193 0.200 4.30 4.50 0.169 0.177 −−− 1.20 −−− 0.047 0.05 0.15 0.002 0.006 0.50 0.75 0.020 0.030 0.65 BSC 0.026 BSC 0.50 0.60 0.020 0.024 0.09 0.20 0.004 0.008 0.09 0.16 0.004 0.006 0.19 0.30 0.007 0.012 0.19 0.25 0.007 0.010 6.40 BSC 0.252 BSC 0_ 8_ 0_ 8_ SOLDERING FOOTPRINT 7.06 1 0.65 PITCH 14X 0.36 14X 1.26 DIMENSIONS: MILLIMETERS Micro8 is a trademark of International Rectifier. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 http://onsemi.com 17 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC33201/D