ML12509 ML12511 ML12513 MECL PLL Components Dual Modulus Prescaler Legacy Device: Motorola 12509, 12511, 12513 These devices are two–modulus prescalers which will divide by 5 and 6, 8 and 9, respectively. A MECL–to–MTTL translator is provided to interface directly with the Motorola MC12014 Counter Control Logic. In addition, there is a buffered clock input and MECL bias voltage source. • ML12509 480 MHz (÷5/6), ML12511 550 MHz (÷8/9), ML12513 550 MHz (÷10/11) • MECL to MTTL Translator on Chip • MECL and MTTL Enable Inputs • 5.0 or –5.2 V Operation* • Buffered Clock Input — Series Input RC Typ, 20 Ω and 4.0 pF • VBB Reference Voltage • 310 mW (Typ) * When using a 5.0 V supply, apply 5.0 V to Pin 1 (VCCO), Pin 6 (MTTL VCC), Pin 16 (VCC), and ground Pin 8 (VEE). When using –5.2 V supply, ground Pin 1 (VCCO), Pin 6 (MTTL VCC), and Pin 16 (VCC) and apply –5.2 V to Pin 8 (VEE). If the translator is not required, Pin 6 may be left open to conserve DC power drain. MAXIMUM RATINGS Characteristic Symbol Rating Unit 16 1 CERDIP 16 = E CERAMIC PACKAGE CASE 620 CROSS REFERENCE/ORDERING INFORMATION PACKAGE MOTOROLA LANSDALE CERDIP 16 CERDIP 16 CERDIP 16 12509/BEA 12511/BEA 12513/BEA ML12509/BEA ML12511/BEA ML12513/BEA PIN CONNECTIONS 16 VCC 15 Clock VCCO Q 1 Q (–) 3 (+) 5 MTTL VCC 6 MTTL Output 7 11 E3 MECL 10 E4 MECL VEE 8 9 E5 MECL 2 14 VBB 13 E1 MECL 12 E2 MECL 4 (Top View) (Ratings above which device life may be impaired) Power Supply Voltage (VCC = 0) VEE –8.0 Vdc Input Voltage (VCC = 0) Vin 0 to VEE Vdc Output Source Current Continuous Surge IO Storage Temperature Range mAdc 50 100 Tstg –65 to 175 °C (Recommended Maximum Ratings above which performance may be degraded) Operating Temperature Range DC Fan–Out (Note 1) (Gates and Flip–Flops) TA –55 to 125 °C n 70 — NOTES: 1. AC fan–out is limited by desired system performance. Page 1 of 12 www.lansdale.com Issue 0 ML12509, ML12511, ML12513 Page 2 of 12 LANSDALE Semiconductor, Inc. www.lansdale.com Issue 0 ML12509, ML12511, ML12513 ELECTRICAL CHARACTERISTICS LANSDALE Semiconductor, Inc. Page 3 of 12 www.lansdale.com Issue 0 ML12509, ML12511, ML12513 ELECTRICAL CHARACTERISTICS LANSDALE Semiconductor, Inc. Page 4 of 12 www.lansdale.com Issue 0 ML12509, ML12511, ML12513 SWITCHING CHARACTERISTICS LANSDALE Semiconductor, Inc. Page 5 of 12 www.lansdale.com Issue 0 ML12509, ML12511, ML12513 LANSDALE Semiconductor, Inc. Figure 5. AC Test Circuit Vin 25 µF 50 Pulse Generator #1 Vout (Scope Channel B) VCC = 2.0 V 100 Vin 50 Pulse Generator #2 100 Vin 1 6 13 E1 12 E2 11 E3 10 E4 9 E5 15 C 0.1 µF 16 Vout 2 Q 3 Vout Q VBB 14 950 Pulse Generator #3 50 5 + 4 – MECL to MTTL Trans– lator 1950 7 8 0.1 µF Vin (Scope Channel A) Pulse Generator #4 CT VEE = –3.0 V MC10109 or equiv. A All Pulse Generators are EH 137 or equiv. Pulse Generators 1, 2 and 4: PRF = 10 MHz PW = 50% Duty Cycle t + = t – = 2.0 ± 0.2 ns Pulse Generator 3: PRF = 2.0 MHz PW = 50% Duty Cycle t + = t – = 5.0 ± 0.5 ns 50 VEE = –3.0 V All resistors are +1%. All input and output cables to the scope are equal lengths of 50 Ω coaxial cable. The 1950 Ω resistor at Pin 7 and the scope termination impedance constitute a 40 :1 attenuator probe. CT = 15 pF = total parasitic capacitance which includes probe, wiring, and load capacitance. Unused output connected to a 50 Ω resistor to ground. NOTES: 1. Test outputs of the device must be tested by sequencing through the truth table. All input, power supply and ground voltages must be maintained between tests. The clock input is the waveform shown. 2. In addition to meeting the output levels specified, the device must divide by 5 or 8 during this test. The clock input is the waveform shown. 3. In addition to meeting the output levels specified, the device must divide by 6 or 9 during this test. The clock input is the waveform shown. Clock Input VIHmax VILmin Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained. Outputs are terminated through a 50 Ω resistor to –2.0 V. Test procedures are shown for only one gate. The other gates are tested in the same manner. Page 6 of 12 www.lansdale.com Issue 0 ML12509, ML12511, ML12513 LANSDALE Semiconductor, Inc. Figure 3. AC Voltage Waveforms Pulse Generator 4 and 1 VIHmin 80% 50% 20% VILmin t++ Q (Pin 2) 50% t+ – 50% Q (Pin 3) + In 50% MTTL Out t++ t–– –1.5 V Figure 4. Setup and Release Time Waveforms Pulse 50 Generator % 1 tsetup1 Pulse Generator tsetup2 2 Pulse Generator +1.5 V 3 Q (Pin 2) Page 7 of 12 80% 20% 80% 50% 20% 90% 10% Divide by 5 — ML12509 Divide by 8 — ML12511 Divide by 10 — ML12513 VIHmin VILmin VIHmin VILmin 0V VEE Pulse Generator 1 Pulse 50% Generator t rel2 2 Pulse Generator 3 –1.5 V Q (Pin 2) www.lansdale.com 80% 20% 50% trel1 80% 20% 90% 10% VIHmin VILmin VIHmin VILmin 0V VEE Divide by 6 — ML12509 Divide by 9 — ML12511 Divide by 11 — ML12513 Issue 0 ML12509, ML12511, ML12513 LANSDALE Semiconductor, Inc. Figure 6. Maximum Frequency Test Circuit Vout VCC = 2.0 V 0.1 µF 1 to Scope 5.0 µF 16 13 E1 Vin 12 VEE (To Scope) Q E2 2 11 E3 10 E4 9 E5 0.1 µF Q 15 3 C 1.0 k 14 VBB 0.1 µF 8 0.1 µF VEE = –3.0 V Unused output connected to a 50 Ω resistor to ground DIVIDE BY 6 800 mV Clock Input 850 mV typ Q (Pin 2) 3 Cycles 3 Cycles DIVIDE BY 9 800 mV Clock Input 850 mV typ Q (Pin 2) Page 8 of 12 5 Cycles 4 Cycles www.lansdale.com Issue 0 ML12509, ML12511, ML12513 Page 9 of 12 LANSDALE Semiconductor, Inc. www.lansdale.com Issue 0 ML12509, ML12511, ML12513 Page 10 of 12 LANSDALE Semiconductor, Inc. www.lansdale.com Issue 0 ML12509, ML12511, ML12513 Page 11 of 11 LANSDALE Semiconductor, Inc. www.lansdale.com Issue 0 ML12509, ML12511, ML12513 LANSDALE Semiconductor, Inc. OUTLINE DIMENSIONS CERDIP 16 = E CERAMIC PACKAGE (ML12509/BEA, ML12511/BEA, ML12513/BEA) CASE 620 Lansdale Semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Lansdale does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. “Typical” parameters which may be provided in Lansdale data sheets and/or specifications can vary in different applications, and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by the customer’s technical experts. Lansdale Semiconductor is a registered trademark of Lansdale Semiconductor, Inc. Page 12 of 12 www.lansdale.com Issue 0