CBC910 Power Manager ASIC Charge Pump and Battery Management ASIC Bare Die Features • • • • • • • • • Power Manager with Charge Control Built-in Battery Protection Temperature Compensated Charge Control Adjustable Switchover Voltage Charges Battery Over a Wide Supply Range Low Standby Power Wire Bond attachment standard Gold solder bump for attachment optional Eco-Friendly, RoHS Compliant • Standby supply for non-volatile SRAM, Real-time clocks, controllers, supply supervisors, and other system-critical components. Wireless sensors and RFID tags and other powered, low duty cycle applications. Localized power source to keep microcontrollers and other devices alert in standby mode. Power bridging to provide back-up power to system during exchange of main batteries. Consumer appliances that have real-time clocks; provides switchover power from main supply to backup battery. Business and industrial systems such as: network routers, point-of-sale terminals, singleboard computers, test equipment, multi-function printers, industrial controllers, and utility meters. Energy Harvesting by coupling the energy storage device with energy transducers such as solar panels. Applications • • • • • • The CBC910 is a power management solution that provides battery backup control and power management for systems requiring power bridging and/or secondary power. During normal operation, the CBC910 delivers a controlled voltage using an internal charge pump that operates from 2.5V to 5.5V. An ENABLE pin allows for activation and deactivation of the charge pump using an external control line in order to minimize current consumption when battery charge current is not needed. When the primary power supply dips below a userdefined threshold voltage, the CBC910 will signal this event and route the battery voltage to VOUT. The CBC910 also has battery protection circuitry to protect an attached battery from being discharged too deeply. The CBC910 is available as a bare die having 9 bond pads. Figure 1 - Typical CBC910 Application Circuit Using External EnerChip Rechargeable Battery as a Backup Power Source for a Real-Time Clock ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 1 of 14 CBC910 Electrical Properties Battery Backup Output voltage: 3.3 V Physical Properties Die size: 0.96 mm x 1.36 mm (to center of scribe on wafer) Operating temperature: -40°C to +85°C Storage temperature: -40°C to +125°C Functional Block Diagram The CBC910 internal schematic is shown in Figure 2. The input voltage from the power supply (VDD) is applied to the charge pump, the control logic, and is compared to the user-set threshold as determined by the voltage on VMODE. VMODE is an analog input ranging from 0V to VDD. The ENABLE pin is a digital input that turns off the charge pump when low. VOUT is either supplied from VDD or the integrated battery. RESET is a digital output that, when low, indicates VOUT is being sourced by a backup battery. CFLY is the flying capacitor in the voltage doubler circuit. The value of CFLY can be changed if the output impedance of the CBC910 needs to be modified. The output impedance is dictated by 1/fC, where f is the frequency of oscillation (typically 100kHz) and C is the capacitor value (typically 0.1µF). GND is system ground. VCHG GND Figure 2: CBC910 Internal Block Diagram ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 2 of 14 CBC910 Device Input/Ouput Descriptions Pin Number Label Description 1 2 3 4 5 6 7 8 VDD VBAT EN GND CN CP RESET/ VOUT Positive Supply 4.1V Charging Source Charge Pump Enable Ground Charge Pump Flying Capacitor (-) Charge Pump Flying Capacitor (+) Battery Backup Indicator Output VDD VBAT VOUT RESET/ ENABLE CP VMODE GND CN Figure 3: CBC910 Die Pad Designations ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 3 of 14 CBC910 Absolute Maximum Ratings PARAMETER CONDITION MIN TYPICAL MAX UNITS VDD with respect to GND 25°C GND - 0.3 - 6.0 V ENABLE and VMODE Input Voltage 25°C GND - 0.3 - VDD+0.3 V VBAT 25°C 3.0 - 4.3 V GND-0.3 GND - 0.3 - 6.0 V RESET Output Voltage 25°C 25°C - VOUT+0.3 V CP, Flying Capacitor Voltage 25°C GND - 0.3 - 6.0 V CN 25°C GND - 0.3 - VDD+0.3 V (1) VOUT (1) No external connections to this pin is allowed, except rechargeable batteries requiring a 4.1V charge voltage. Operating Characteristics PARAMETER Output Voltage VOUT CONDITION MIN TYPICAL MAX UNITS VDD > VTH VDD 25 85 V °C - +125 (2) °C Operating Temperature - -40 Storage Temperature - -40 Note: All specifications contained within this document are subject to change without notice. ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 4 of 14 CBC910 POWER SUPPLY CURRENT CHARACTERISTICS Ta = -40ºC to +85ºC CHARACTERISTIC SYMBOL CONDITION ENABLE=GND Quiescent Current IQ ENABLE=VDD Backup Battery Cutoff Current MIN MAX UNITS VDD=3.3V - 3.5 µA VDD=5.5V VDD=3.3V VDD=5.5V - 6.0 µA - 35 µA - 38 µA IQBATOFF VBAT < VBATCO, VOUT=0 - 0.5 nA IQBATON VBAT > VBATCO, ENABLE=VDD, IOUT=0 - 42 nA INTERFACE LOGIC SIGNAL CHARACTERISTICS VDD = 2.5V to 5.5V, Ta = -40ºC to +85ºC CHARACTERISTIC SYMBOL CONDITION MIN MAX UNITS High Level Input Voltage Low Level Input Voltage VIH VIL - VDD - 0.5 - Volts - - 0.5 Volts High Level Output Voltage VOH VDD>VTH (see Figures 4 and 5) IL=10µA VDD 0.04V (1) - Volts Low Level Output Voltage VOL IL = -100µA - 0.3 Volts Logic Input Leakage Current IIN 0<VIN<VDD -1.0 +1.0 nA (1) RESET tracks VDD; RESET = VDD - (IOUT x ROUT). RESET SIGNAL AC/DC CHARACTERISTICS VDD = 2.5V to 5.5V, Ta = -40ºC to +85ºC CHARACTERISTIC SYMBOL CONDITION MIN MAX UNITS VDD Rising to RESET Rising tRESETH VDD rising from 2.8V TO 3.1V in <10µs 60 200 ms VDD Falling to RESET Falling Mode 1 TRIP V VDD Rising tRESETL VDD falling from 3.1V to 2.8V in <100ns 0.2 60 µs VRESET VMODE = GND 2.80 3.20 V Mode 2 TRIP V (2) VDD Rising VRESET VMODE = VDD/2 2.25 2.60 V VMODE=VDD 60 100 VMODE=GND 45 75 VMODE = VDD/2 30 50 RESET Hysteresis Voltage (3) (VDD to RESET) VHYST mV (2) User-selectable trip voltage can be set by placing a resistor divider from the VMODE pin to GND. Refer to Figure 6. (3) The hysteresis is a function of trip level in Mode 2. Refer to Figure 7. ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 5 of 14 CBC910 CHARGE PUMP CHARACTERISTICS VDD = 2.5V to 5.5V, Ta = -40ºC to +85ºC CHARACTERISTIC ENABLE=VDD to Charge Pump Active ENABLE Falling to Charge Pump Inactive SYMBOL tCPON CONDITION MIN MAX UNITS 60 80 µs 0 1 µs - 120 KHz (1) 150 300 Ω ENABLE to 3rd charge pump pulse, VDD=3.3V tCPOFF - Charge Pump Frequency fCP Charge Pump Resistance RCP Delta VBAT, for IBAT charging current of 1µA to 100µA CFLY=0.1µF, CBAT=1.0µF VCHG Output Voltage VCP CFLY=0.1µF, CBAT=1.0µF, IOUT=1µA, Temp=+25ºC 4.075 4.125 V VCHG Temp. Coefficient TCCP ICP IOUT=1µA, Temp=+25ºC -2.0 -2.4 mV/ºC IBAT=1mA CFLY=0.1µF, CBAT=1.0µF 1.0 - mA ENABLE=VDD 2.5 - V Charge Pump Current Drive Charge Pump on Voltage (1) VENABLE fCP = 1/tCPPER ADDITIONAL CHARACTERISTICS Ta = -40ºC to +85ºC CHARACTERISTIC SYMBOL CONDITION LIMITS UNITS MIN MAX 2.75 3.25 V +1 +2 mV/ºC VBAT Cutoff Threshold Cutoff Temp. Coefficient VBATCO TCCO IOUT=1µA VBAT Cutoff Delay Time tCOOFF VBAT from 40mV above to 20mV below VBATCO IOUT=1µA 18 - ms VOUT Dead Time, VDD Rising (2) VOUT Dead Time, VDD Falling (2) Bypass Resistance tRSBR IOUT=1mA VBAT=4.1V 0.1 7.5 µs tRSBF VBAT=4.1V 0.2 65 µs - 2.5 Ω (2) ROUT - - Dead time is the time period when the VOUT pin is floating. Size the holding capacitor accordingly. Note: All specifications contained within this document are subject to change without notice ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 6 of 14 CBC910 Important timing diagrams for the CBC910 relationship between Battery Switchover Timing and Battery Disconnect from Load Timing are shown in Figure 4. Battery Switchover Timing VDD VTH Vreset User Selectable Threshold VOUT VOUT=VDD VOUT=VBAT 2.5 Volts tRSBR tRSBF tRSBR Battery Disconnect From Load Timing Battery Backup Mode VOUT=(VBAT-0.6) typical Battery Disonnect Threshold VBCO VOUT=(VBAT-0.6) typical tCOOFF Figure 4: CBC910 Switchover and Disconnect Timing Diagrams ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 7 of 14 CBC910 Timing diagrams for the CBC910 relationship between VDD to RESET and ENABLE high to charge pump becoming active are shown in Figure 5. Figure 5: Timing Diagrams for VDD to RESET and Enable to Charge Pump Active. ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 8 of 14 CBC910 CBC910 Detailed Description The CBC910 uses a charge pump to generate the supply voltage for charging a battery. An internal FET switch with low RDSON is used to route VDD to VOUT during normal operation when main power is above the battery switchover threshold voltage. When VDD is below the battery switchover threshold voltage, the FET switch is shut off and VOUT is supplied by the battery through a silicon diode in series between VBAT and VOUT. An interrupt signal is asserted low prior to the switchover. Operating Modes The EnerChip CC can be operated from various power supplies such as a primary source or a non-rechargeable battery. With the ENABLE pin asserted high, the charge pump is active and charges the integrated EnerChip. The EnerChip CC will be 80% charged within 10 minutes. Due to the rapid recharge it is recommended that, once the EnerChip CC is fully charged, the user de-assert the ENABLE pin (i.e., force low) to reduce power consumption. A signal generated from the MCU could be used to enable and disable the EnerChip CC. When controlling the ENABLE pin by way of an external controller - as opposed to fixing the ENABLE line to VDD - ensure that the ENABLE pin is forced low by the controller anytime the RESET line is low, which occurs when the switchover threshold voltage is reached and the device is placed in backup mode. Although the internal charge pump is designed to operate below the threshold switchover level when the ENABLE line is active, it is recommended that the ENABLE pin be forced low whenever RESET is low to ensure no parasitic loads are placed on the EnerChip while in this mode. If ENABLE is high or floating while VDD is in an indeterminate state, bias currents within the EnerChip CC could flow, placing a parasitic load on the EnerChip that could dramatically reduce the effective backup operating time. Mode 1 Operation For use in 3.3 volt systems. The VMODE pin should be tied directly to GND. This will set the battery switchover threshold at approximately 3.0 volts. Mode 2 Operation To adjust the user-selectable battery switchover threshold to a value between 2.5 and 5.0 volts, refer to Figure 6 to determine the value of R1. To determine the amount of hysteresis from the backup battery switchover threshold, use Figure 7. ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 9 of 14 CBC910 Battery charging and backup power for 2.5 to 5.5 volt operation is selected by changing the value of R2. To determine the battery backup switchover point, set the value of R1 to 200kΩ and choose the value of R2 according to Figure 6. For example, to set a 3.0V trip point: If R1=200 kΩ then R2 = R1 x 0.72 = 144kΩ. Battery Switchover Threshold Voltage vs. R2/R1 Ratio Switchover Threshold Voltage (Volts) 6 5 4 3 Trip point 2 1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 R2/R1 Ratio Figure 6: MODE 2 Resistor Selection Graph To determine the battery backup switchover hysteresis for Mode 2 operation, use Figure 7. Hysteresis in Battery Switchover Threshold Voltage vs. R2/R1 Ratio 0.09 0.08 Hysteresis (Volts) 0.07 0.06 0.05 Hysteresis 0.04 0.03 0.02 0.01 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 1.1 R2/R1 Ratio Figure 7: Mode 2 Hysteresis as a Function of R2/R1 ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 10 of 14 CBC910 Energy Harvesting with the CBC910 The CBC910 bare die ASIC can be configured to collect energy from transducers such as low power photovoltaic (PV) cells and use that harvested energy to charge the integrated EnerChip and deliver self-sustaining power to components such as microcontrollers, sensors, and radios in wireless systems. A feedback connection made from RESET to EN to implement the energy harvesting function. The CBC910 will be connected to one or more EnerChip batteries for energy storage. In order to make most efficient use of the power available from the transducer (for example, a PV cell), It is necessary to know the electrical characteristics including voltage and peak power point of the transducer being used. For assistance in designing your system to effectively harvest energy from a power transducer in a specific environment, contact Cymbet Applications Engineering. ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 11 of 14 CBC910 Example of using a CBC910 bare die in an 8 Lead VDFN Figure 8: Example CBC910 Wirebond Diagram in an 8L VDFN Notes: Pad size = 1.75mm x 2.66mm Pad pitch = 0.61mm ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 12 of 14 CBC910 CBC910 Partial Wafer Map when Purchasing wafers 126.35 (street center to pad center) 126.35 (street center to pad center) 328.4 (street center to pad center) 340.35 (street center to pad center) Notes: 1) Scribe lane is 150um (x) 150um (y) 2) Die thickness is 150um minimum. 200um maximum. 3) All dimensions in microns. ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 13 of 14 CBC910 CBC910 Die Pad Locations VDD VOUT VBAT RESET/ ENABLE 1102 Trim4 51.35 558.15 265.35 253.4 464.35 CN GND 847.15 VMODE 675.55 888.9 1102 CP 707.3 Notes: 1) All dimensions measured to the center of the respective bond pad and measured relative to the lower left corner of metal-2 on the Trim4 pad as shown below. That Trim4 coordinate is the 0,0 reference point for the data extents of the die. Total die size is 150um larger in x and y as defined by the street width. 2) Die size to center of scribe is 960um (x) by 1360um (y). 3) Drawing not to scale. All dimensions in microns. Ordering Information EnerChip CC Part Number CBC910-BDC-WP CBC910-BGC-WP CBC910-WAF Description CBC910 Bare Die Wirebond Pad CBC910 Bare Die Gold Bumped CBC910 Bare Die Notes Shipped in Waffle Pack Shipped in Waffle Pack Shipped as Wafer Disclaimer of Warranties; As Is The information provided in this data sheet is provided “As Is” and Cymbet Corporation disclaims all representations or warranties of any kind, express or implied, relating to this data sheet and the Cymbet battery product described herein, including without limitation, the implied warranties of merchantability, fitness for a particular purpose, non-infringement, title, or any warranties arising out of course of dealing, course of performance, or usage of trade. Cymbet battery products are not approved for use in life critical applications. Users shall confirm suitability of the Cymbet battery product in any products or applications in which the Cymbet battery product is adopted for use and are solely responsible for all legal, regulatory, and safety-related requirements concerning their products and applications and any use of the Cymbet battery product described herein in any such product or applications. Cymbet, the Cymbet Logo, and EnerChip are Cymbet Corporation Trademarks ©2012-2014 Cymbet Corporation • Tel: +1-763-633-1780 • www.cymbet.com DS-72-11 Rev A Page 14 of 14