Cadeka CLC1003ASO8X Low distortion, low offset, rrio amplifier Datasheet

Data Sheet
A m p l i fy t h e H u m a n E x p e r i e n c e
Comlinear CLC1003
®
Low Distortion, Low Offset, RRIO Amplifier
General Description
Applications
n Active filters
n Sensor interface
n High-speed transducer amp
n Medical instrumentation
n Probe equipment
n Test equipment
n Smoke detecters
n Hand-held analytic instruments
Typical Application - Current Sensing in 3-Phase Motor
The COMLINEAR CLC1003 is a single channel, high-performance, voltage
feedback amplifier with near precision performance, low input voltage noise,
and ultra low distortion. The CLC1003 family of amplifiers offers 1mV maximum input offset voltage, 3.5nV/√Hz broadband input voltage noise, and
0.00005% THD at 1kHz. These amplifiers also provide 55MHz gain bandwidth
product and 12V/μs slew rate making them well suited for applications requiring precision DC performance and high AC performance. These COMLINEAR
high-performance amplifiers also offer a rail-to-rail input and output, simplifying single supply designs and offering larger dynamic range possibilities. The
inputs extend beyond the rails by 500mV.
The COMLINEAR CLC1003 family of amplifiers are designed to operate from
2.5V to 12V supplies and operate over the extended temperature range of
-40°C to +125°.
VCC
+
CLC1003
lph_1
–
SPM
(Smart
Power
Module)
M
lph_2
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
features
n 1mV max input offset voltage
n 0.00005% THD at 1kHz
n 5.3nV/√Hz input voltage noise >10kHz
n -90dB/-85dB HD2/HD3 at 100kHz, RL=100Ω
n <-100dB HD2 and HD3 at 10kHz, RL=1kΩ
n Rail-to-Rail input and output
n 55MHz unity gain bandwidth
n 12V/μs slew rate
n +80mA, -55mA output current
n -40°C to +125°C operating temperature
range
n Fully specified at 3V and ±5V supplies
n CLC1003: Pb-free SOT23-5, SOIC-8
n Future option CLC2003: Dual
n Future option CLC4003: Quad
Rev 1A
lph_3
Ordering Information
Part Number
Package
Pb-Free
RoHS Compliant
Operating Temperature Range
Packaging Method
CLC1003IST5X
SOT23-5
Yes
Yes
-40°C to +85°C
Reel
CLC1003ISO8X*
SOIC-8
Yes
Yes
-40°C to +85°C
Reel
CLC1003ISO8*
SOIC-8
Yes
Yes
-40°C to +85°C
Rail
CLC1003AST5X
SOT23-5
Yes
Yes
-40°C to +125°C
Reel
CLC1003ASO8X*
SOIC-8
Yes
Yes
-40°C to +125°C
Reel
CLC1003ASO8*
SOIC-8
Yes
Yes
-40°C to +125°C
Rail
*Preliminary Product Information
Moisture sensitivity level for all parts is MSL-1.
©2008 CADEKA Microcircuits LLC www.cadeka.com
Data Sheet
CLC1003 SOT Pin Configuration
OUT
1
-V S
2
3
+
-IN
4
CLC1003 SOIC Pin Configuration
NC
-IN1
Pin Name
Description
1
OUT
Output
2
-VS
Negative supply
3
+IN
Positive input
4
-IN
Negative input
5
+VS
Positive supply
CLC1003 SOIC Pin Assignments
Pin No.
Pin Name
Description
No connect
1
NC
1
8
NC
2
-IN1
Negative input
2
7
+VS
3
+IN1
Positive input
4
-VS
Negative supply
5
NC
No connect
6
OUT
Output
7
+VS
Positive supply
8
NC
No connect
+IN1
3
6
OUT
-V S
4
5
NC
CLC2003 Pin Configuration
OUT1
1
8
+VS
-IN1
2
7
OUT2
+IN1
3
6
-IN2
-V S
4
5
+IN2
CLC4003 Pin Configuration
CLC2003 (Future Option) Pin Configuration
Pin No.
Pin Name
1
OUT1
Description
Output, channel 1
2
-IN1
Negative input, channel 1
3
+IN1
Positive input, channel 1
4
-VS
5
+IN2
Positive input, channel 2
6
-IN2
Negative input, channel 2
7
OUT2
Output, channel 2
8
+VS
Negative supply
Positive supply
CLC4003 (Future Option) Pin Configuration
Pin No.
Pin Name
Description
1
OUT1
Output, channel 1
1
14
OUT4
2
-IN1
Negative input, channel 1
-IN1
2
13
-IN4
3
+IN1
Positive input, channel 1
+IN1
3
12
+IN4
4
+VS
Positive supply
+VS
4
11
-VS
5
+IN2
Positive input, channel 2
6
-IN2
Negative input, channel 2
+IN2
5
10
+IN3
7
OUT2
Output, channel 2
-IN2
6
9
-IN3
8
OUT3
Output, channel 3
7
8
OUT3
OUT2
©2004-2008 CADEKA Microcircuits LLC 9
-IN3
Negative input, channel 3
10
+IN3
Positive input, channel 3
11
-VS
12
+IN4
Positive input, channel 4
13
-IN4
Negative input, channel 4
14
OUT4
Output, channel 4
Rev 1A
OUT1
Pin No.
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
+IN
+VS
5
CLC1003 SOT23-5 Pin Assignments
Negative supply
www.cadeka.com
2
Data Sheet
Absolute Maximum Ratings
The safety of the device is not guaranteed when it is operated above the “Absolute Maximum Ratings”. The device
should not be operated at these “absolute” limits. Adhere to the “Recommended Operating Conditions” for proper device function. The information contained in the Electrical Characteristics tables and Typical Performance plots reflect the
operating conditions noted on the tables and plots.
Supply Voltage
Input Voltage Range
Min
Max
Unit
0
-Vs -0.5V
14
+Vs +0.5V
V
V
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
Parameter
Reliability Information
Parameter
Junction Temperature
Storage Temperature Range
Lead Temperature (Soldering, 10s)
Package Thermal Resistance
5-Lead SOT23
8-Lead SOIC
14-Lead SOIC
Min
Typ
-65
Max
Unit
150
150
260
°C
°C
°C
221
100
88
°C/W
°C/W
°C/W
Notes:
Package thermal resistance (qJA), JDEC standard, multi-layer test boards, still air.
Recommended Operating Conditions
Parameter
Min
Operating Temperature Range (CLC1003I)
Operating Temperature Range (CLC1003A)
Supply Voltage Range
-40
-40
2.5
Typ
Max
Unit
+85
+125
12
°C
°C
V
Rev 1A
©2004-2008 CADEKA Microcircuits LLC www.cadeka.com
3
Data Sheet
Electrical Characteristics at +3V
TA = 25°C, Vs = +3V, Rf = 1kΩ, RL = 1kΩ to VS/2, G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
-3dB Gain Bandwidth Product
G = 10, VOUT = 0.05Vpp
31
MHz
UGBW
Unity Gain Bandwidth
BWSS
-3dB Bandwidth
VOUT = 0.05Vpp , Rf = 0
50
MHz
VOUT = 0.05Vpp
24
BWLS
Large Signal Bandwidth
MHz
VOUT = 2Vpp
3.3
MHz
Time Domain Response
tR, tF
Rise and Fall Time
VOUT = 2V step; (10% to 90%)
150
ns
tS
Settling Time to 0.1%
VOUT = 2V step
78
ns
OS
Overshoot
VOUT = 2V step
0.3
%
SR
Slew Rate
2V step
11
V/µs
2Vpp, 10kHz, RL = 1kΩ
-98
dBc
2Vpp, 100kHz, RL = 100Ω
-85
dBc
2Vpp, 10kHz, RL = 1kΩ
-95
dBc
-81
dBc
Distortion/Noise Response
HD2
2nd Harmonic Distortion
HD3
3rd Harmonic Distortion
THD
Total Harmonic Distortion
en
Input Voltage Noise
2Vpp, 100kHz, RL = 100Ω
1Vpp, 1kHz, G=1, RL = 2kΩ
0.0005
%
> 10kHz
5.5
nV/√Hz
> 100kHz
3.9
nV/√Hz
0.088
mV
µV/°C
DC Performance
VIO
dVIO
Input Offset Voltage
Average Drift
1.3
Ib
Input Bias Current
-0.340
μA
dIb
Average Drift
0.8
nA/°C
Ios
Input Offset Current
0.2
nA
PSRR
Power Supply Rejection Ratio
DC
100
dB
AOL
Open-Loop Gain
VOUT = VS / 2
104
dB
IS
Supply Current
per channel
1.85
mA
Input Characteristics
Input Resistance
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio
Non-inverting, G = 1
DC , Vcm=0.5V to 2.5V
30
MΩ
1.1
pF
-0.5 to
3.5
V
94
dB
0.085 to
2.80
V
0.04 to
2.91
V
+75, -40
mA
+95, -50
mA
Rev 1A
RIN
Output Characteristics
RL = 150Ω
VOUT
Output Voltage Swing
IOUT
Output Current
ISC
Short-Circuit Output Current
RL = 1kΩ
VOUT = VS / 2
Notes:
1. 100% tested at 25°C
©2004-2008 CADEKA Microcircuits LLC www.cadeka.com
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
GBWP
4
Data Sheet
Electrical Characteristics at ±5V
TA = 25°C, Vs = ±5V, Rf = 1kΩ, RL = 1kΩ to GND, G = 2; unless otherwise noted.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Frequency Domain Response
-3dB Gain Bandwidth Product
G = 10, VOUT = 0.05Vpp
35
MHz
UGBW
Unity Gain Bandwidth
BWSS
-3dB Bandwidth
VOUT = 0.05Vpp , Rf = 0
55
MHz
VOUT = 0.05Vpp
25
BWLS
Large Signal Bandwidth
MHz
VOUT = 2Vpp
3.6
MHz
Time Domain Response
tR, tF
Rise and Fall Time
VOUT = 2V step; (10% to 90%)
125
ns
tS
Settling Time to 0.1%
VOUT = 2V step
80
ns
OS
Overshoot
VOUT = 2V step
0.3
%
SR
Slew Rate
4V step
12
V/µs
2Vpp, 10kHz, RL = 1kΩ
-125
dBc
2Vpp, 100kHz, RL = 100Ω
-90
dBc
2Vpp, 10kHz, RL = 1kΩ
-127
dBc
-85
dBc
Distortion/Noise Response
HD2
2nd Harmonic Distortion
HD3
3rd Harmonic Distortion
THD
Total Harmonic Distortion
en
Input Voltage Noise
2Vpp, 100kHz, RL = 100Ω
1Vpp, 1kHz, G=1, RL = 2kΩ
0.00005
%
> 10kHz
5.3
nV/√Hz
> 100kHz
3.5
nV/√Hz
DC Performance
VIO
dVIO
Ib
dIb
Input Offset Voltage(1)
-1
0.050
-2.6
-0.30
Average Drift
1
1.3
Input Bias Current (1)
Average Drift
µV/°C
2.6
0.85
μA
nA/°C
Ios
Input Offset Current (1)
PSRR
Power Supply Rejection Ratio (1)
DC
82
100
dB
AOL
Open-Loop Gain (1)
VOUT = VS / 2
95
115
dB
IS
Supply Current
per channel
2.2
Non-inverting, G = 1
30
MΩ
1
pF
(1)
0.2
mV
0.7
2.75
μA
mA
Input Characteristics
RIN
Input Resistance
CIN
Input Capacitance
CMIR
Common Mode Input Range
CMRR
Common Mode Rejection Ratio (1)
DC , Vcm= -3V to 3V
70
±5.5
V
95
dB
-4.826
to 4.534
V
RL = 150Ω
VOUT
Output Voltage Swing
IOUT
Output Current
ISC
Short-Circuit Output Current
RL = 1kΩ (1)
VOUT = VS / 2
-4.7
-4.93 to
4.85
4.7
Rev 1A
Output Characteristics
V
+80, -55
mA
+115, -90
mA
Notes:
1. 100% tested at 25°C
©2004-2008 CADEKA Microcircuits LLC www.cadeka.com
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
GBWP
5
Data Sheet
Typical Performance Characteristics
TA = 25°C, Vs = ±5V, Rf = 1kΩ, RL = 1kΩ to GND, G = 2; unless otherwise noted.
Non-Inverting Frequency Response
Inverting Frequency Response
1
0
0
-1
Normalized Gain (dB)
Normalized Gain (dB)
G=1
Rf = 0
G=2
-3
G=5
G = 10
-6
G = -1
-2
G = -2
-3
G = -5
G = -10
-4
-5
-6
VOUT = 0.05Vpp
-9
VOUT = 0.05Vpp
-7
0.1
1
10
100
0.1
1
Frequency (MHz)
10
100
10
100
Frequency (MHz)
Frequency Response vs. CL
Frequency Response vs. CL without RS
1
4
-1
2
CL = 500pF
Rs = 10Ω
-2
Normalized Gain (dB)
Normalized Gain (dB)
0
CL = 1000pF
Rs = 7.5Ω
-3
CL = 3000pF
Rs = 4Ω
-4
-5
CL = 500pF
0
CL = 300pF
-2
CL = 100pF
-4
CL = 50pF
-6
-6
-7
-8
0.1
1
10
100
CL = 10pF
VOUT = 0.05Vpp
Rs = 0Ω
VOUT = 0.05Vpp
0.1
1
Frequency (MHz)
Frequency (MHz)
Frequency Response vs. VOUT
Frequency Response vs. RL
3
2
Normalized Gain (dB)
Normalized Gain (dB)
0
VOUT = 1Vpp
VOUT = 2Vpp
-3
VOUT = 4Vpp
-6
RL = 150Ω
0
RL = 2.5KΩ
-1
RL = 1KΩ
-2
-3
-4
-5
-9
Rev 1A
RL = 50Ω
1
VOUT = 0.05Vpp
-6
0.1
1
10
Frequency (MHz)
©2004-2008 CADEKA Microcircuits LLC 100
0.1
1
10
100
Frequency (MHz)
www.cadeka.com
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
3
6
Data Sheet
Typical Performance Characteristics
TA = 25°C, Vs = ±5V, Rf = 1kΩ, RL = 1kΩ to GND, G = 2; unless otherwise noted.
Non-Inverting Frequency Response at VS = 3V
Inverting Frequency Response at VS = 3V
1
0
0
-1
Normalized Gain (dB)
Normalized Gain (dB)
G=1
Rf = 0
G=2
-3
G=5
G = 10
-6
G = -1
-2
G = -2
-3
G = -5
G = -10
-4
-5
-6
VOUT = 0.05Vpp
-9
VOUT = 0.05Vpp
-7
0.1
1
10
100
0.1
1
Frequency (MHz)
10
Frequency Response vs. VOUT at VS = 3V
Frequency Response vs. RL at VS = 3V
3
2
RL = 50Ω
1
0
Normalized Gain (dB)
Normalized Gain (dB)
100
Frequency (MHz)
VOUT = 1Vpp
VOUT = 2Vpp
-3
VOUT = 2.5Vpp
-6
RL = 150Ω
0
RL = 2.5KΩ
-1
RL = 1KΩ
-2
-3
-4
-5
-9
VOUT = 0.05Vpp
-6
0.1
1
10
100
0.1
1
Frequency (MHz)
10
100
Frequency (MHz)
-3dB Bandwidth vs. Output Voltage at VS = 3V
-3dB Bandwidth vs. Output Voltage
24
Rev 1A
24
21
-3dB Bandwidth (MHz)
-3dB Bandwidth (MHz)
21
18
15
12
9
6
3
18
15
12
9
6
3
0
0
0.0
0.5
1.0
1.5
VOUT (VPP)
©2004-2008 CADEKA Microcircuits LLC 2.0
2.5
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
3
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
VOUT (VPP)
www.cadeka.com
7
Data Sheet
Typical Performance Characteristics - Continued
TA = 25°C, Vs = ±5V, Rf = 1kΩ, RL = 1kΩ to GND, G = 2; unless otherwise noted.
Open Loop Gain and Phase vs. Frequency
CMIR
-75
PHASE
-150
20
-225
GAIN
0
-300
-20
-375
-40
-450
-60
0.3
PHASE (°)
40
0.4
Vout (V)
60
GAIN (dB)
0.5
0
0.1
0
-0.1
-525
10
100
1,000
10,000
100,000
0.2
-6
1,000,000
-4
-2
0
2
4
6
Vni(V)
FREQ (KHz)
Input Voltage Noise
CMIR at VS = 3V
14
0.5
12
0.4
11
10
0.3
9
Vout (V)
Input Voltage Noise (nV/√Hz)
13
8
7
6
0.2
0.1
5
4
0
3
2
-0.1
0.0001
0.001
0.01
0.1
1
-1
-0.5
0
0.5
Frequency (MHz)
2
2.5
3
3.5
4
PSRR vs. Frequency
110
100
100
90
90
CMRR (dB)
110
80
70
80
70
60
60
50
50
40
Rev 1A
CMRR (dB)
1.5
Vni(V)
CMRR vs. Frequency
0.001
1
40
0.01
0.1
1
Frequency (MHz)
©2004-2008 CADEKA Microcircuits LLC 10
100
1000
0.001
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
80
0.01
0.1
1
10
100
1000
Frequency (MHz)
www.cadeka.com
8
Data Sheet
Typical Performance Characteristics - Continued
TA = 25°C, Vs = ±5V, Rf = 1kΩ, RL = 1kΩ to GND, G = 2; unless otherwise noted.
2nd Harmonic Distortion vs. RL
3rd Harmonic Distortion vs. RL
-60
RL = 100Ω
RL = 10KΩ
-70
Distortion (dBc)
Distortion (dBc)
-60
-80
-90
RL = 10KΩ
RL = 1KΩ
-70
RL = 100Ω
-80
-90
RL = 1KΩ
RL = 500Ω
RL = 500Ω
-100
-100
VOUT = 2Vpp
VOUT = 2Vpp
-110
-110
100
200
300
400
500
600
700
800
900
100
1000
200
300
400
2nd Harmonic Distortion vs. VOUT
600
700
800
900
1000
3rd Harmonic Distortion vs. VOUT
-40
-30
-40
-50
-50
-60
Distortion (dBc)
Distortion (dBc)
500
Frequency (KHz)
Frequency (KHz)
RF=RL=1K
-70
-80
-60
RF=RL=1K
-70
-80
RF=RL=10K
RF=RL=10K
-90
-90
FREQ = 500KHz
-100
FREQ = 500KHz
-100
0.5
1.5
2.5
3.5
4.5
5.5
6.5
7.5
8.5
9.5
Output Amplitude (Vpp)
0.5
1.5
2.5
3.5
4.5
5.5
6.5
7.5
8.5
9.5
Output Amplitude (Vpp)
THD vs. Frequency
-65
Rev 1A
-70
-75
THD (dB)
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
-50
-50
-80
-85
-90
VOUT = 1Vpp
RL = 1K
AV+1
-95
-100
100
200
300
400
500
600
700
800
900
1000
Frequency (kHz)
©2004-2008 CADEKA Microcircuits LLC www.cadeka.com
9
Data Sheet
Typical Performance Characteristics - Continued
TA = 25°C, Vs = ±5V, Rf = 1kΩ, RL = 1kΩ to GND, G = 2; unless otherwise noted.
3rd Harmonic Distortion vs. RL at VS = 3V
-40
-40
-50
-50
-70
-80
RL = 10KΩ
RL = 1KΩ
RL = 500Ω
Distortion (dBc)
RL = 100Ω
-60
-60
RL = 100Ω
-70
-80
RL = 500Ω
RL = 10KΩ
RL = 1KΩ
-90
-90
VOUT = 2Vpp
VOUT = 2Vpp
-100
-100
100
200
300
400
500
600
700
800
900
100
1000
200
300
500
600
700
800
900
1000
3rd Harmonic Distortion vs. VOUT at VS = 3V
-40
-40
-50
-50
-60
Distortion (dBc)
Distortion (dBc)
2nd Harmonic Distortion vs. VOUT at VS = 3V
RF=RL=10K
-70
-80
400
Frequency (KHz)
Frequency (KHz)
RF=RL=1K
-90
-60
RF=RL=10K
-70
-80
RF=RL=1K
-90
FREQ = 500KHz
FREQ = 500KHz
-100
-100
0.5
0.75
1
1.25
1.5
1.75
2
2.25
2.5
Output Amplitude (Vpp)
0.5
0.75
1
1.25
1.5
1.75
2
2.25
2.5
Output Amplitude (Vpp)
THD vs. Frequency at VS = 3V
-65
Rev 1A
-70
-75
THD (dB)
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
Distortion (dBc)
2nd Harmonic Distortion vs. RL at VS = 3V
-80
-85
-90
VOUT = 1Vpp
RL = 1K
AV+1
-95
-100
100
200
300
400
500
600
700
800
900
1000
Frequency (kHz)
©2004-2008 CADEKA Microcircuits LLC www.cadeka.com
10
Data Sheet
Typical Performance Characteristics - Continued
TA = 25°C, Vs = ±5V, Rf = 1kΩ, RL = 1kΩ to GND, G = 2; unless otherwise noted.
Small Signal Pulse Response
Small Signal Pulse Response at VS = 3V
1.6
0.25
1.55
Voltage (V)
0.5
Voltage (V)
1.65
0
1.5
-0.25
1.45
-0.5
1.4
-0.75
1.35
0
0.5
1
1.5
2
0
0.5
Time (ns)
1.5
2
Large Signal Pulse Response at VS = 3V
6
3
4
2.5
2
2
Voltage (V)
Voltage (V)
Large Signal Pulse Response
0
1.5
-2
1
-4
0.5
-6
0
0
1
2
3
4
5
6
7
8
9
10
0
0.5
1
Time (ns)
1.5
2
Time (ns)
Input Offset Voltage vs. Temperature
Input Offset Voltage Distribution
5000
0.05
4000
Rev 1A
0.1
0
3000
Units
Vio (V)
1
Time (ns)
-0.05
2000
-0.1
1000
-0.15
©2004-2008 CADEKA Microcircuits LLC 100
120
0.98
80
0.7
60
0.42
40
Temperature (°C)
0.14
20
-0.14
0
-0.42
-20
-0.7
-40
-0.98
0
-0.2
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
0.75
Input Offset Voltage (mV)
www.cadeka.com
11
Data Sheet
Application Information
perature, the package thermal resistance value ThetaJA
(ӨJA) is used along with the total die power dissipation.
Basic Operation
+Vs
Input
6.8μF
Output
RL
0.1μF
Rf
6.8μF
Figure 1. Typical Non-Inverting Gain Circuit
R1
Input
Rg
Pload = ((VLOAD)RMS2)/Rloadeff
The effective load resistor (Rloadeff) will need to include
the effect of the feedback network. For instance,
RL || (Rf + Rg)
6.8μF
Output
0.1μF
6.8μF
-Vs
Vsupply = VS+ - VS-
Rloadeff in figure 3 would be calculated as:
0.1μF
+
Psupply = Vsupply × IRMS supply
Power delivered to a purely resistive load is:
G = 1 + (Rf/Rg)
-Vs
+Vs
In order to determine PD, the power dissipated in the load
needs to be subtracted from the total power delivered by
the supplies.
Supply power is calculated by the standard power equation.
-
Rg
Where TAmbient is the temperature of the working environment.
PD = Psupply - Pload
0.1μF
+
TJunction = TAmbient + (ӨJA × PD)
RL
Rf
These measurements are basic and are relatively easy to
perform with standard lab equipment. For design purposes
however, prior knowledge of actual signal levels and load
impedance is needed to determine the dissipated power.
Here, PD can be found from
PD = PQuiescent + PDynamic - PLoad
G = - (Rf/Rg)
For optimum input offset
voltage set R1 = Rf || Rg
Figure 2. Typical Inverting Gain Circuit
Power dissipation should not be a factor when operating
under the stated 300 ohm load condition. However, applications with low impedance, DC coupled loads should
be analyzed to ensure that maximum allowed junction
temperature is not exceeded. Guidelines listed below can
be used to verify that the particular application will not
cause the device to operate beyond it’s intended operating range.
Maximum power levels are set by the absolute maximum
junction rating of 150°C. To calculate the junction tem-
©2004-2008 CADEKA Microcircuits LLC Rev 1A
Power Dissipation
Quiescent power can be derived from the specified IS values along with known supply voltage, VSupply. Load power
can be calculated as above with the desired signal amplitudes using:
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
Figures 1 and 2 illustrate typical circuit configurations for
non-inverting, inverting, and unity gain topologies for dual
supply applications. They show the recommended bypass
capacitor values and overall closed loop gain equations.
(VLOAD)RMS = VPEAK / √2
( ILOAD)RMS = ( VLOAD)RMS / Rloadeff
The dynamic power is focused primarily within the output
stage driving the load. This value can be calculated as:
PDYNAMIC = (VS+ - VLOAD)RMS × ( ILOAD)RMS
Assuming the load is referenced in the middle of the power rails or Vsupply/2.
Figure 3 shows the maximum safe power dissipation in
the package vs. the ambient temperature for the packages available.
www.cadeka.com
12
Data Sheet
For a given load capacitance, adjust RS to optimize the
tradeoff between settling time and bandwidth. In general,
reducing RS will increase bandwidth at the expense of additional overshoot and ringing.
2
SOIC-8
1.5
SOT23-6
Overdrive Recovery
1
0.5
0
-40
-20
0
20
40
60
80
Ambient Temperature (°C)
Figure 3. Maximum Power Derating
An overdrive condition is defined as the point when either one of the inputs or the output exceed their specified
voltage range. Overdrive recovery is the time needed for
the amplifier to return to its normal or linear operating
point. The recovery time varies, based on whether the
input or output is overdriven and by how much the range
is exceeded. The CLCx003 will typically recover in less
than 20ns from an overdrive condition. Figure 5 shows the
CLC1003 in an overdriven condition.
3
Driving Capacitive Loads
Input
2
2
Input Voltage (V)
1
1
Input
1
0
0
Output
-1
-1
Output Voltage (V)
Increased phase delay at the output due to capacitive loading can cause ringing, peaking in the frequency response,
and possible unstable behavior. Use a series resistance,
RS, between the amplifier and the load to help improve
stability and settling performance. Refer to Figure 4.
2
VIN = .8Vpp
G=5
-1
+
Rs
-
Output
CL
Rf
-2
-2
-3
RL
-2
0
0.25
0.5
0.75
1
1.25
1.5
1.75
2
Time (us)
Rg
Figure 5. Overdrive Recovery
Figure 4. Addition of RS for Driving
Capacitive Loads
CL (pF)
RS (Ω)
-3dB BW (MHz)
500
10
27
1000
7.5
20
3000
4
15
Table 1: Recommended RS vs. CL
Offset Analysis
There are three sources of offset contribution to consider;
input bias current, input bias current mismatch, and input
offset voltage. The input bias currents are assumed to
be equal with and additional offset current in one of the
inputs to account for mismatch. The bias currents will not
affect the offset as long as the parallel combination of Rf
and Rg matches Rt. Refer to Figure 6.
+Vs
Rf
Rg
–
IN
Rt
CLC1003
+
RL
-Vs
Figure 6: Circuit for Evaluating Offset
©2004-2008 CADEKA Microcircuits LLC www.cadeka.com
13
Rev 1A
The CLC1003 family of amplifiers is capable of driving up to
300pF directly, with no series resistance. Directly driving
500pF causes over 4dB of frequency peaking, as shown in
the plot on page 6. Table 1 provides the recommended RS
for various capacitive loads. The recommended RS values
result in <=1dB peaking in the frequency response. The
Frequency Response vs. CL plots, on page 6, illustrates
the response of the CLCx003.
Considerations for Offset and Noise Performance
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
Maximum Power Dissipation (W)
2.5
Data Sheet
Rt = Rg||Rf
Where Vorext is the noise due to the external resistors and
is given by:
2
v
o
= en 1 +
RF
RG
2
RF
RG
+ eG ∗
2
2
+ eF
The complete equation can be simplified to:
This equation can be rearranged to solve for Rg:
2
v
o
Rg = (Rt * Rf) / (Rf - Rt)
(
2
) ( )
= 3 ∗ 4kT ∗ G ∗ RT + enG
(
+ 2 ∗ in ∗ RT
2
)
The other consideration is desired gain (G) which is:
G = (1 + Rf/Rg)
By plugging in the value for Rg we get
Rf = G * Rt
And Rg can be written in terms of Rt and G as follows:
Rg = (G * Rt) / (G - 1)
The complete input offset equation is now only dependent
on the voltage offset and input offset terms given by:
VI OS =
2
2
( VIO ) + (IOS ∗ RT)
And the output offset is:
VO OS = G ∗
2
It’s easy to see that the effect of amplifier voltage noise
is proportionate to gain and will tend to dominate at large
gains. The other terms will have their greatest impact at
large Rt values at lower gains.
Layout Considerations
General layout and supply bypassing play major roles in
high frequency performance. CADEKA has evaluation
boards to use as a guide for high frequency layout and as
aid in device testing and characterization. Follow the steps
below as a basis for high frequency layout:
• Include 6.8µF and 0.1µF ceramic capacitors for power
supply decoupling
2
( V IO ) + (I OS ∗ RT )
• Place the 6.8µF capacitor within 0.75 inches of the power pin
Noise analysis
• Place the 0.1µF capacitor within 0.1 inches of the power pin
The complete equivalent noise circuit is shown in Figure 7.
• Remove the ground plane under and around the part,
especially near the input and output pins to reduce parasitic capacitance
Rg
Rf
+–
+–
+–
+
+–
RL
w
+
–
Refer to the evaluation board layouts below for more information.
CLC1003
Rg
Evaluation Board Information
The following evaluation boards are available to aid in the
testing and layout of these devices:
Figure 7: Complete Equivalent Noise Circuit
The complete noise equation is given by:
2
v
o
2
RF
= vorext + en 1 +
RG
2
+ ibp ∗ RT 1 +
©2004-2008 CADEKA Microcircuits LLC RF
RG
Evaluation Board #
2
(
+ ibn ∗ RF
2
)
CEB002
CEB003
Products
CLC1003 in SOT23-5
CLC1003 in SOIC-8
www.cadeka.com
14
Rev 1A
• Minimize all trace lengths to reduce series inductances
–
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
The first place to start is to determine the source resistance. If it is very small an additional resistance may need
to be added to keep the values of Rf and Rg to practical
levels. For this analysis we assume that Rt is the total resistance present on the non-inverting input. This gives us
one equation that we must solve:
Data Sheet
Evaluation Board Schematics
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
Evaluation board schematics and layouts are shown in Figures 8-13. These evaluation boards are built for dual- supply operation. Follow these steps to use the board in a
single-supply application:
1. Short -Vs to ground.
2. Use C3 and C4, if the -VS pin of the amplifier is not
directly connected to the ground plane.
Figure 10. CEB002 Bottom View
Figure 8. CEB002 Schematic
Figure 11. CEB003 Top View
Rev 1A
Figure 9. CEB002 Top View
©2004-2008 CADEKA Microcircuits LLC Figure 12. CEB003 Bottom View
www.cadeka.com
15
Data Sheet
Mechanical Dimensions
SOT23-5 Package
Comlinear CLC1003 Low Distortion, Low Offset, RRIO Amplifier
SOIC-8
Rev 1A
For additional information regarding our products, please visit CADEKA at: cadeka.com
CADEKA Headquarters Loveland, Colorado
T: 970.663.5452
T: 877.663.5415 (toll free)
CADEKA, the CADEKA logo design, and Comlinear and the Comlinear logo design, are trademarks or registered trademarks of CADEKA
Microcircuits LLC. All other brand and product names may be trademarks of their respective companies.
CADEKA reserves the right to make changes to any products and services herein at any time without notice. CADEKA does not assume any
responsibility or liability arising out of the application or use of any product or service described herein, except as expressly agreed to in
writing by CADEKA; nor does the purchase, lease, or use of a product or service from CADEKA convey a license under any patent rights,
copyrights, trademark rights, or any other of the intellectual property rights of CADEKA or of third parties.
Copyright ©2008 by CADEKA Microcircuits LLC. All rights reserved.
A m p l i fy t h e H u m a n E x p e r i e n c e