EGP20A THRU EGP20K 2.0 AMPS. Glass Passivated High Efficient Plastic Rectifiers Voltage Range 50 to 800 Volts Current 2.0 Amperes DO-15 Features Plastic material used carries Underwriters Laboratory Classification 94V-0 Glass passivated cavity-free junction Superfast recovery time for high efficiency Low forward voltage, high current capability Low leakage current High surge current capability High temperature metallurgically bonded construction High temperature soldering guaranteed: 300℃/10 seconds, .375”(9.5mm) lead length at 5 lbs., (2.3kg) tension Mechanical Data Cases: JEDEC DO-15 molded plastic over glass body Lead: Plated axial leads, solderable per MIL-STD750, Method 2026 Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.015 ounce, 0.4 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Symbol EGP VRRM VRMS VDC 20A EGP 20B EGP 20D EGP 20F EGP 20G EGP 20J EGP 20K Units 50 35 50 100 70 100 200 140 200 300 210 300 400 280 400 600 420 600 800 560 800 V V V Maximum Average Forward Rectified Current .375”(9.5mm) Lead Length @ TA = 55℃ I(AV) 2.0 A Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) IFSM 75.0 A Maximum Instantaneous Forward Voltage @ 2.0A VF Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=125℃ IR Maximum Reverse Recovery Time ( Note 1 ) Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) 0.95 1.25 5.0 100 1.7 50 Trr Cj 40 RθJA RθJL TJ ,TSTG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1.0 MHz and Applied VR=4.0 Volts 3. Mount on Cu-Pad Size 10mm x 10mm on P.C.B. Operating and Storage Temperature Range - 588 - 75 35 60 20 -65 to + 150 V uA uA nS pF ℃/W ℃ RATINGS AND CHARACTERISTIC CURVES (EGP20A THRU EGP20K) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A 1cm 100 RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH 2.0 1.0 0 0 25 50 75 100 125 150 175 o PEAK FORWARD SURGE CURRENT. (A) AMBIENT TEMPERATURE. ( C) 90 FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT Tj=150 0C 10 1 Tj=125 0C 0.1 Tj=75 0C 0.01 Tj=25 0C Tj=Tj max. 8.3ms Single Half Sine Wave JEDEC Method 75 0.001 60 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 45 FIG.6- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 30 50 PULSE WIDTH-300 S 1% DUTY CYCLE 15 0 1 100 10 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 140 JUNCTION CAPACITANCE.(pF) SET TIME BASE FOR 5/ 10ns/ cm FIG.5- TYPICAL REVERSE CHARACTERISTICS FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE Tj=25 0C f=1.0MHz Vsig=50mVp-p 120 100 80 60 40 20 0 0.1 INSTANTANEOUS FORWARD CURRENT. (A) AVERAGE FORWARD CURRENT. (A) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 3.0 0 -0.25A INSTANTANEOUS REVERSE CURRENT. ( A) (+) 50Vdc (approx) (-) 10 Tj=150 0C 1 Tj=25 0C 0.1 EGP20A-EGP20D EGP20F EGP20K EGP20A-EGP20D EGP20F-EGP20K 1 10 0.01 100 1000 REVERSE VOLTAGE. (V) - 589 - 0.2 0.4 0.6 0.8 1.0 1.2 1.4 FORWARD VOLTAGE. (V) 1.6 1.8