MPS EV2361DQ-00A 2a, 1.4mhz step-down converter evaluation board Datasheet

TM
EV2361DK/DQ-00A
2A, 1.4MHz Step-Down Converter
Evaluation Board
The Future of Analog IC Technology
TM
DESCRIPTION
FEATURES
The EV2361DK/DQ-00A is the evaluation board
for the MP2361, a monolithic step down switch
mode converter with a built in internal power
MOSFET.
The
MP2361
achieves
2A
continuous output current over a wide input
supply range with excellent load and line
regulation.
•
•
•
•
•
•
•
•
•
Current mode operation provides fast transient
response and eases loop stabilization.
2A Output Current with QFN Package
Up to 90% Efficiency
20µA Shutdown Mode
Fixed 1.4MHz Frequency
Thermal Shutdown
Cycle-by-Cycle Over Current Protection
Wide 4.75V to 23V Operating Input Range
Output Adjustable from 0.92V to 16V
Programmable Under Voltage Lockout
Fault condition protection includes cycle-by-cycle
current limiting and thermal shutdown. In
shutdown mode the regulator draws 20µA of
supply
current.
Programmable
soft-start
minimizes the inrush supply current and the
output overshoot at initial startup.
APPLICATIONS
The MP2361 requires a minimum number of
readily available standard external components.
“MPS” and “The Future of Analog IC Technology” are Trademarks of Monolithic
Power Systems, Inc.
•
•
•
•
Distributed Power Systems
Set Top Boxes
DSL Modems
Pre-Regulator for Linear Regulators
ELECTRICAL SPECIFICATIONS
Parameter
Input Voltage
Output Voltage
Output Current (1)
Symbol
Value
Units
VIN
VOUT
IOUT
4.75 to 23
3.3
2
V
V
A
Note:
1) The maximum output current may be less than 2A if
VOUT>60% of VIN.
EV2361DK/DQ-00A EVALUATION BOARD
Efficiency vs
Load Current
100
VOUT=5V
EFFICIENCY (%)
90
80
VOUT=2.5V
VOUT=3.3V
70
60
(L x W x H) 2.1” x 1.3” x 0.4”
(5.3cm x 3.3cm x 1.0cm)
Board Number
MPS IC Number
EV2361DK/DQ-00A
MP2361DK/DQ
50
0
0.5
1.0
1.5
LOAD CURRENT (A)
EV2361DK/DQ-00A Rev. 1.3f
www.MonolithicPower.com
10/5/2005
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
2.0
MP2361-EC01
1
TM
EV2361DK/DQ-00A – 2A, 1.4MHz STEP-DOWN CONVERTER EV BOARD
EVALUATION BOARD SCHEMATIC
U1
NC
SS
BS
EN
SS
EN
C7
OPEN
C1
10nF
NC
COMP
C3
1.5nF
R5
OPEN
C4
OPEN
VOUT
VIN
IN
FB
C8
OPEN
GND
SW
GND
GND
MP2361
D1
B230A-13
30V/2A
EV2361DK/DQ-00A BILL OF MATERIALS
Qty
Ref
Value
1
C1
10nF
1
C2
10µF
1
C3
1.5nF
3
C4, C7,
C8
OPEN
1
C5
1
C6
1
D1
1
L1
1
R1
2
R2, R3
Description
Ceramic Capacitor,
50V, X7R
Ceramic Capacitor
25V, X7R
Ceramic Capacitor
50V, X7R
Ceramic Capacitor
16V, X5R
Ceramic Capacitor
0.47µF
25V, X7R
SM0805 TDK
C2012X7R1H103K
SM1210 TDK
C3225X7R1E106M
SM0805 Panasonic
ECJ-2VB1H152K
SM1210 TDK
C3225X5R1C226M
SM0805 TDK
C2012X7R1E474K
Schottky Diode, 30V, 2A
SMA
Diodes Inc
B230A-13
Inductor, 2.4A
SMD
Sumida
CDRH6D28-5R0NC
26.1kΩ Resistor, 1%
10kΩ
Manufacturer P/N
Do Not Stuff
22µF
5µH
Package Manufacturer
SM0805 Panasonic
ERJ-6ENF2610V
Resistor, 1%
SM0805 Panasonic
ERJ-6ENF1002V
SM0805 Panasonic
ERJ-6GEYJ104V
QFN10/
MPS
MSOP10
MP2361DQ/MP2361DK
1
R4
100kΩ Resistor, 5%
1
R5
OPEN
1
U1
Do Not Stuff
Step-Down Converter
EV2361DK/DQ-00A Rev. 1.3f
www.MonolithicPower.com
10/5/2005
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
2
TM
EV2361DK/DQ-00A – 2A, 1.4MHz STEP-DOWN CONVERTER EV BOARD
PRINTED CIRCUIT BOARD LAYOUT
Figure 1—Top Silk Layer
Figure 2—Top Layer
Figure 3—Bottom Layer
QUICK START GUIDE
1. Connect the positive terminal of the load to the VOUT pins, and the negative terminal of the load
to the GND pins
2. Preset the power supply output to 4.75V to 23V and turn off the power supply.
3. Connect the positive terminal of the power supply output to the VIN pin and the negative
terminal of the power supply output to the GND pin
4. Turn the power supply on. The MP2361 will automatically startup.
5. To use the Enable function, apply a digital input to EN pin. Drive EN higher than 2.5V to turn on
the regulator, drive EN less than 0.7V to turn it off.
6. An input under voltage lockout (UVLO) function can be implemented by the addition of a resistor
divider R4 and R5.
⎛
The EN threshold is 2.5V, so VIN UVLO threshold is: ⎜1 +
⎝
R4 ⎞
⎟ × 2.5 V .
R5 ⎠
NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications.
Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS
products into any application. MPS will not assume any legal responsibility for any said applications.
EV2361DK/DQ-00A Rev. 1.3f
www.MonolithicPower.com
10/5/2005
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
3
Similar pages