Engineering Bulletin HXC Introductory No.849C/May.2015 Conductive Polymer Hybrid Aluminum Electrolytic Capacitors Series High reliability and high voltage are realized by hybrid electrolyte Endurance with ripple current : 4,000 hours at 125℃ Rated voltage range : 16 to 35Vdc, Capacitance range : 150 to 470μF For high temperature and high reliability applications. (Automotive equipment, Base station equipment, etc.) ● Halogen Free. ● ● ● ● ◆ SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance -55 to +125℃ 16 to 35Vdc ±20%（M） I=0.01CV Where, I : Max. leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V) 16V 25V 35V Rated voltage (Vdc) tanδ(Max.) 0.16 0.14 0.12 Leakage Current Dissipation Factor (tanδ) Low Temperature Characteristics (Max. Impedance Ratio) Endurance (at 20℃ , 120Hz) (at 20℃ after 2 minutes) (at 20℃ , 120Hz) Z(-25℃ ) / Z(+20℃ ) ≦ 1.5 Z(-55℃ ) / Z(+20℃ ) ≦ 2.0 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated ripple current is applied (the peak voltage shall not exceed the rated voltage) for 4,000 hours at 125℃ . Capacitance change ≦ ±30％ of the initial value D.F. (tanδ) ≦ 200％ of the initial specified value ESR ≦ 200％ of the initial specified value Leakage current ≦ The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 125℃ without voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4. Capacitance change ≦ ±30％ of the initial value D.F. (tanδ) ≦ 200％ of the initial specified value ESR ≦ 200％ of the initial specified value Leakage current ≦ The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to the DC rated voltage at 85℃ , 85% RH for 2,000 hours. Appearance No significant damage Capacitance change ≦ ±30％ of the initial value D.F. (tanδ) ≦ 200％ of the initial specified value ESR ≦ 200％ of the initial specified value Leakage current ≦ The initial specified value Shelf Life Bias Humidity Test ◆ MARKING ◆ DIMENSIONS ［mm］ ●Terminal Code : A EX) 35V150μF ⊕ W 26A Size Code HA0 JA0 C±0.2 B±0.2 φD±0.5 P Vent for JA0 L A B C W φD 8 10.0 8.3 8.3 9.0 0.7 to 1.1 10 10.0 10.3 10.3 11.0 0.7 to 1.1 P 3.1 4.5 ⊖ 150 V HC ⊕ ●Rated voltage symbol Rated voltage (Vdc) 16 25 35 A±0.2 0.3max. ⊖ L±0.5 ◆ PART NUMBERING SYSTEM 1 2 3 4 H HXC 5 6 7 8 9 10 A RA 11 12 13 14 M 15 16 17 Symbol C E V 18 G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 150μF:151, 470μF:471) Taping code Terminal code Voltage code (ex. 16V:160,35V:350) Series code Category Please contact us for mass production schedule. Specifications in this bulletin are subject to change without notice. NIPPON CHEMI-CON CORPORATION 1755 1 ALUMINUM ELECTROLYTIC CAPAC Engineering Bulletin Introductory No.849C/May.2015 Engineering Bulletin RECOMMENDED Tentative No.824C / Oct.2012 HXCSeries NPCAP TM PMA ◆SURFACE MOUNT TYPE - Conductive Polymer Hybrid Aluminum Electrolytic Capacitors SOLDERING CONDIT Conductive Polymer Aluminum Solid Capacitors Series ◆ STANDARD RATINGS AlchipTM MVA/MVE/MZR/MZJ/MZA/MVY/MZF/MZE/M MVL/MVJ/MVH/MHL/MHB/MHJ/MHK/MKB/M ◆STANDARD RATINGS WV (Vdc) WV (Vdc) 16 Cap (μF) Cap (μF) 270 470 220 330 150 270 39 68 150 220 47 150 15 22 56 ESR Rated ripple current Part No. Size code Rated ripple current ESR (mArms/125℃ , 100kHz) (mΩ max/20℃ , 100kHz) Leakage current (mArms/100kHz) (mΩmax/20℃, Part No. (µAmax/after 2min.) 100k to 300kHz) -55℃≦Tx≦+85℃*1 +85℃<Tx≦ +105℃*1 HA0 22 1,700 HHXC160ARA271MHA0G 40 2,700 2,200 APMA160ARA390MF40S JA0 312 18 2,100 HHXC160ARA471MJA0G 544 40 2,700 2,200 APMA160ARA680MF40S HA0 27 1,600 HHXC250ARA221MHA0G 1,200 18 4,100 3,300 APMA160ARA151MF60S JA01,760 20 2,000 HHXC250ARA331MJA0G 18 4,100 3,300 APMA160ARA221MF60S HA0 470 27 1,600 HHXC350ARA151MHA0G 45 2,600 2,100 APMA200ARA470MF40S JA01,500 20 2,000 HHXC350ARA271MJA0G 20 3,700 3,200 APMA200ARA151MF60S 187 50 2,400 2,000 APMA250ARA150MF40S 275 50 2,400 2,000 APMA250ARA220MF40S 700 26 3,400 2,800 APMA250ARA560MF60S Size code F40 F40 following conditions are recommended for air convection and infrared re The F60 F60 circuit boards by cream solder. The dimensions of the glass epoxy boards with F40 2035 F60 capacitors and 180×90×0.8mm for LH0 to MN0 case codes SMD capacitors. F40 F40 25 The temperatures shown are the surface temperature values on the top of the c F60 RECOMMENDED REFLOW SOLDERING CONDITIONS ◆ *1 Tx: Ambient temperature Reflow should be performed twice or less. The following conditions are recommended for air convection and infrared reflow soldering on the SMD products on to a glass epoxy circuit boards by cream solder. Theensure dimensions that of the glass boards with became resist are 90×50×0.8mm. Please theepoxy capacitor cold enough to the room temperature The temperatures shown are the surface temperature values on the top of the can and on the capacitor terminals. ◆RECOMMENDEDConsult REFLOW SOLDERING CONDITIONS Reflow should be performed twice orwith less. us when performing reflow profile in IPC / JEDEC (J-STD-020) 16 25 ●Reflow Profilethat the capacitor became cold enough to the room temperature (5 to 35℃ ) before the second reflow. Please ensure ●Recommended ● Reflow Profile soldering heat conditions (Except for Conductive Polymer Temperature on the top of capacitor and Temperature of capacitor terminal Temp (℃) (℃) Peak temp. Peak Peak 230 230 Peak temperature SMD type Voltage range (Vdc) 4 to 63V Size code Max. period time over 230℃ Max. period of of time over 230℃ 217 217 63V(MVH), 80V Preheat Vertical Preheat Time maintained 4 to 50V H63 to JA0 63 to 100, 400V 6.3 to 50V KE0 to MN0 Time (sec.)Time (sec.) Size Code ● Voltage range(Vdc ) (Except 63V for MVH) D55 to F90 Max. period of time over 217℃ Max. period of time over 217℃ 63 to 450V Time maintained Preheat Peak temp. Reflow number Time maintained Time maintained above 217℃ aboveBoard 230℃ Recommended Solder Land on PC Preheat Peak temp. Reflow number above 217℃ above 230℃ 150 to 180℃ 150℃ to 180℃ 120 sec. max. 120 sec.max. HA0, JA0 16 to 25V 50 sec.max. 50 sec. max. 40 sec.max. 260℃ max. 1-cycle only 40 sec.max. 1-cycle only 40 sec. max. 250℃ max. 245℃ max. 2-cycle allowed 30 sec.max. 2-cycle allowed D55, D60, D E55, E60, E F55, F60, F H63 HA0 JA0 KE0, KG5 LH0, LN0 MH0, MN0 c ●Recommended Solder Land(Based on the PX series) [mm] b a b : Solder land on PC board Solder land on PC board Location of capacitor c b a b Size code a b c F40,F60 1.9 3.5 1.6 Location ofLEAD capacitor ◆RADIAL AND SNAP-IN TYPE ● Recommended soldering heat conditions Flow soldering ：260±5℃ for 10+1 seconds Specifications in this bulletin are subject to change without notice. Please ask us for technical specifications before purchase and use. Hand soldering ：380±10℃ for 3±0.5 seconds NIPPON CHEMI-CON CORPORATION ◆PRECAUTIONS FOR USERS 1595 2 Please contact us for mass production schedule. Specifications in this bulletin are subject to change without notice. NIPPON CHEMI-CON CORPORATION Soldering method 1755 The capacitors of Alchip-series have no capability to withstand such dip Rework o 2 Use a solde