Hybrid Aluminum Electrolytic Capacitors NSPE-HZ Series • CYLINDRICAL V-CHIP CONSTRUCTION FOR SURFACE MOUNTING • EXTENDED LOAD LIFE AT HIGH TEMPERATURE (2000 ~ 5,000 HOURS @ +105°C) • VOLTAGE RATINGS (16 ~ 40VDC) • ULTRA LOW ESR AND HIGH RIPPLE CURRENT RATINGS • 6.3x6.3mm ~ 10x12.8mm CASE SIZES • HIGH REFLOW SOLDERING TEMPERATURE (+260°C) • MEETS THE REQUIREMENTS OF AEC-Q200* *Contact NIC for supporting test data CHARACTERISTICS Rated Voltage Range Rated Capacitance Range Operating Temp. Range Capacitance Tolerance Max. Leakage Current After 2 Minutes @ 20°C 16 ~ 40Vdc 18 ~ 560μF -55 ~ +105°C ±20% (M) All Values Less than 0.01CV or 3μA whichever is greater W.V. (Vdc) S.V. (Vdc) Working and Surge Voltage Ratings 16 20 25 32 Tan δ @ 120Hz/20°C Load Life Test @ 105°C and Rated Voltage 40 50 0.16 0.75 ~ 1.25 0.75 ~ 1.25 Z -55°C/Z +20°C Z +105°C/Z +20°C W.V. (Vdc) φ6.3mm Case Dia. φ8 & 10mm Capacitance Change Tan δ and ESR Leakage Current Impedance Ratio 35 44 16 25 35 2000 hrs. 5000 hrs. Within ±30% of initial measured value Less than 200% of specified max. value Less than specified max. value 40 STANDARD PRODUCTS AND CASE SIZES Dφ x L (mm) NSPE-HZ820M16V6.3X6.3NBYF Cap. (μF) 82 NSPE-HZ121M16V6.3X8NBYF 120 PART NUMBER Working Case Size Voltage (D X L) mm 6.3X6.3 6.3X8 16 Max. ESR (mΩ) AT 100KHz/20°C 38 Max. Ripple Current (mA rms) AT 100KHz/105°C 1890 Load Life Hours (+105°C) 2000 32 2070 2000 NSPE-HZ271M16V8X10.8NBYF 270 8X10.8 23 2820 5000 NSPE-HZ471M16V10X10.8NBYF 470 10X10.8 18 3750 5000 NSPE-HZ561M16V10X12.8NBYF 560 10X12.8 14 4340 5000 NSPE-HZ470M25V6.3X6.3NBYF 47 6.3X6.3 40 1800 2000 NSPE-HZ680M25V6.3X8NBYF 68 6.3X8 35 1980 2000 NSPE-HZ151M25V8X10.8NBYF 150 8X10.8 25 2690 5000 NSPE-HZ271M25V10X10.8NBYF 270 25 10X10.8 19 3580 5000 NSPE-HZ331M25V10X12.8NBYF 330 10X12.8 14 4140 5000 NSPE-HZ270M35V6.3X6.3NBYF 27 6.3X6.3 50 1530 2000 NSPE-HZ470M35V6.3X8NBYF 47 6.3X8 45 1840 2000 NSPE-HZ101M35V8X10.8NBYF 100 8X10.8 28 2550 5000 NSPE-HZ151M35V10X10.8NBYF 150 35 10X10.8 20 3490 5000 NSPE-HZ221M35V10X12.8NBYF 220 10X12.8 15 4000 5000 NSPE-HZ180M40V6.3X6.3NBYF 18 6.3X6.3 55 1510 2000 NSPE-HZ270M40V6.3X8NBYF 27 6.3X8 48 1770 2000 NSPE-HZ560M40V8X10.8NBYF 56 8X10.8 30 2450 5000 NSPE-HZ101M40V10X10.8NBYF 100 10X10.8 21 3380 5000 NSPE-HZ121M40V10X12.8NBYF 120 10X12.8 16 3870 5000 40 RIPPLE CURRENT FREQUENCY CORRECTION FACTORS Cap. μF C < 4.7 5.6 ~ 33 > 33 100Hz 0.03 0.05 0.10 1KHz 0.30 0.32 0.35 10KHz 0.65 0.67 0.70 100KHz 1.00 1.00 1.00 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com 1 Hybrid Aluminum Electrolytic Capacitors NSPE-HZ Series PART NUMBER SYSTEM NSPE-HZ 101 M 35V 8x10.8 N B Y F RoHS Compliant B = Sn-Bi Finish, 13" Reel, LB=Sn-Bi Finish, 15" Reel Reflow Temp. Code (N=+260°C) Size in mm Working Voltage Tolerance Code M=20% Capacitance Code in μF, first 2 digits are significant Third digit is no. of zeros, “R” indicates decimal for values under 10μF Series Suitable for automotive equipment, sourced to special production and inspection at TS-16949 certified production site Code B BY LB LBY Plating Sn-Bi Sn-Bi Sn-Bi Sn-Bi A, B ±0.2 6.6 6.6 8.3 10.3 10.3 W 0.5 ~ 0.8 0.5 ~ 0.8 0.7 ~ 1.0 1.0 ~ 1.4 1.0 ~ 1.4 Termination Type Standard Standard Standard Standard Automotive No Yes No Yes Reel Size 13" Reel 13" Reel 15" Reel 15" Reel DIMENSIONS (mm) Case Size 6.3X6.3 6.3X8 8X10.8 10X10.8 10X12.8 Dφ ±0.5 6.3 6.3 8.0 10 10 L max. 6.3 8.0 10.8 10.8 12.8 + Dφ I I ±0.2 2.5 2.5 2.9 3.2 3.2 I P ±0.2 2.2 2.2 3.2 4.6 4.6 - W 0.3mm max. Part Marking Series Code Lot Code Z__ 68 25V Capacitance Value A L Voltage P B PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] 2 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Hybrid Aluminum Electrolytic Capacitors NSPE-HZ Series STANDARD TERMINATION LAND PATTERN DIM. (mm) Case Dia. 6.3 8 10 A 3.6 4.1 4.4 B 1.8 2.1 2.5 + P 1.8 2.8 4.3 B A P A Temperature - Deg. C RECOMMENDED REFLOW SOLDERING PROFILE* Peak Temperature (+260°C) 260 230 200 Time Above 230°C (40 sec.) 150 Time Above 200°C (100 sec.) 100 Preheat - 120 seconds max. (150°C ~ 190°C) 50 Time (Seconds) PEAK TEMPERATURE AND DURATION Time above Time above Time above Peak 200°C 217°C 230°C Temperature 6.3 ~ 10mm 100 sec. max. 80 sec. max. 40 sec. max. 260°C/5 sec. *Two reflow passes are permissible with a cool down to room temperature required between the first and second pass. Diameter Review & Compare Reflow Soldering Heat Limits V-chip SMT Aluminum Electrolytic Capacitors www.niccomp.com/RSL NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com 3 Hybrid Aluminum Electrolytic Capacitors NSPE-HZ Series TAPING SPECIFICATIONS (mm) 1. Both Leader and Trailer tape: Minimum 40mm (1.57") empty carrier tape pockets. 2. Leader tape: Approximately 20cm of cover tape at leader. 3. Connection: Maximum 3 connections (slices) per reel. CARRIER DIMENSIONS (mm) D ±0.1 7.5 7.5 11.5 11.5 11.5 P ±0.1 12.0 12.0 16.0 16.0 16.0 T ±0.2 6.5 8.2 11.1 11.2 13.3 t max. 0.6 0.6 0.6 0.6 0.6 6.3X6.3 6.3X8 8X10.8 10X10.8 10X12.8 W ±1.0 18 18 26 26 26 + A P Feeding T 2mm ± 0.5mm REEL DIMENSIONS (mm) Case Size - t B C ±0.3 16.0 16.0 24.0 24.0 24.0 D B ±0.5 7.0 7.0 8.7 10.7 10.7 1.75 ± Qty per Reel 13" (330mm) 15" (380mm) 800 1000 500 900 300 500 300 500 300 400 φ13mm ± 0.5mm φ50mm min. 6.3X6.3 6.3X8 8X10.8 10X10.8 10X12.8 A ±0.5 7.0 7.0 8.7 10.7 10.7 1.75 + 0.15 1.5∅ +0.1/1.5φ+0.1/-0 C Case Size 4 + 0.1 φ21mm ± 0.8mm φ330mm ± 2.0mm or φ380mm ± 2.0mm 4 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com W www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE 3mm www.SMTmagnetics.com