Anachip AP435 Dual linear controller with shutdown Datasheet

AP435/435L
Dual Linear Controller With Shutdown
( Preliminary )
Features
General Descriptions
-Power shutdown (SD) control
-Fixed output voltage reference 1.25V
-Voltage precision:
AP435L: 1.25 + 0.4%
AP435 : 1.25 + 1%
-Wide power supply range: 3 to 32V
-Sourcing current capability: 1 to 200mA
-Typical output impedance: 0.2Ω
The AP435/435L is a linear controller IC with
Shutdown function, wired to a 1.25V fixed Voltage
Reference. This device is offering space and cost
saving in many applications like power supply
management or data acquisition systems.
Ordering Information
AP435 X X X
■ Application
-Computer
-Disk driver
-CD-ROM
-Graphic Card
-TFT panel
Precision
Package
Packing
Blank: 1%
L : 0.4%
N: PDIP-8L
S: SOP-8L
Blank: Tube
A : Taping
Pin Descriptions
Pin Assignments
( Top view )
FB1
1
8
FB2
VCC
2
7
OUT2
OUT1
3
6
SD1
GND
4
5
SD2
Name
Descriptions
OUT1
FB1/2
VCC
GND
SD1/2
OUT2
Output1
Output Feedback
Supply Voltage
Ground
Power shutdown control
Output2
( DIP8/SO8 )
Block Diagram
VCC
FB1
FB2
Error
Amp1
10K
Error
Amp2
VCC
OUT2
OUT1
SD1
Vref
GND
SD2
This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of
this product. No rights under any patent accompany the sale of the product.
Rev. 0.B Dec. 02, 2002
1/5
AP435/435L
Dual Linear Controller With Shutdown
( Preliminary )
Absolute Maximum Ratings
Symbol
Parameter
VCC
VSD
VESD
Rating
Unit
36
2
V
V
KV
Input Voltage
-0.3 ~ +36
V
Operating temperature range
Storage temperature range
-55 ~ +125
-65 ~ +150
100
ºC
ºC
Supply Voltage
Shutdown pin
ESD
VIN
TOP
TST
θJA (DIP package)
θJA (SOP package)
TJ
Thermal resistance junction to Ambient
ºC/W
160
Maximum junction temperature
150
ºC
Electrical Characteristics ( TAMB=25ºC, VCC=5V)
Symbol
VCC
Input voltage
Parameter
ICC(ACTIVE)
Supply current
Conditions
Min.
Typ. Max.
3
32
Vcc(+)=5V, No Load
,TMIN<TAMB<TMAX
0.7
1.2
Unit
V
mA
ICC(SHUTDOWN)
Error-amp ( VCC = 5V, TAMB=25OC,unless otherwise notice )
Symbol
VIO
Parameter
Input Offset voltage
Vicm = 0V
ISOURCE
ISHORT
ISINK
IIB
Input Offset voltage Drift
Supply voltage rejection
ratio
Output current source
Short circuit to Ground
Output current Sink
Input bias current
VOH
High Level output voltage
VOL
Low Level output voltage
AVD
Large signal voltage gain
SR
Slew rate at unity gain
DVIO
SVRR
GBP
Gain bandwidth product
THD
Total Harmonic Distortion
Conditions
Min.
TAMB=25OC
AP435
TMIN<TAMB<TMAX
TAMB=25OC
AP435L
TMIN<TAMB<TMAX
Typ.
Max.
Unit
1
4
5
2
3
mV
0.5
0.5
7
VCC+=5~30V
65
100
VCC=+15V,VO=2V,VID=+1V
VCC=+15V
VCC=+15V,VO=2V,VID=-1V
Negative input
TAMB=25OC,RL=10K
VCC+=30V,TMIN<TAMB<TMAX
RL=10K
TMIN<TAMB<TMAX
VCC=+15V,VO=1.4~11.4V,
RL=2K TMIN<TAMB<TMAX
VI=0.5~3V,VCC=15V,RL=2K
,
CL=100pF,unity gain
VCC=30V,RL=2K,CL=100pF
f = 100Khz,VIN=10mV
20
40
40
20
20
VCC=30V,RL=2K,CL=100pF
f = 1Khz,Vo=2VP-P,AV=20dB
Anachip Corp.
www.anachip.com.tw
10
27
µV / °C
dB
60
28
5
mA
mA
mA
nA
V
20
mV
100
V/mV
0.3
0.5
V / µs
0.5
0.9
MHz
0.02
%
Rev. 0.B Dec. 02, 2002
2/5
AP435/435L
Dual Linear Controller With Shutdown
Voltage reference
Symbol
Parameter
( Preliminary )
Conditions
O
VREF
Reference input voltage
TAMB=25 C
TMIN<TAMB<TMAX
TAMB=25OC
AP435L
TMIN<TAMB<TMAX
AP435
Min.
1.237
1.225
1.245
1.237
Reference input voltage
VKA=VREF,IK=10mA
deviation over
TMIN<TAMB<TMAX
Temperature range
Minimum cathode current
IMIN
VKA=VREF
for regulation
Ik
Cathode Current
VKA=VREF
Dynamic impedance
│ZKA│
ΔIK=1~100mA , f=0
(note1)
Note 1: The dynamic impedance is defined as│ZKA│=ΔVKA/ΔIK
ΔVREF
Shutdown control
Symbol
Parameter
VSDL
VSDH
ISD
Threshold voltage
Conditions
Active mode
Shutdown mode
Min.
Typ.
Max.
Unit
1.25
1.263
1.275
1.255
1.263
V
3.0
20
mV
0.15
0.3
mA
0.2
1
mA
0.2
0.5
Ω
Typ.
Max.
Unit
0.2
V
V
uA
0.8
Current in shutdown mode
Typical Application Circuit
5V
AP435
3.3V
VCC
FB1
12V
22uF
22uF
Error
Amp1
FB2
10K
OUT2
VCC
NMOS1
SD1
OUT1
2.5V
R1=1K
Vref
GND
22uF
NMOS2
Error
Amp2
3.3V
R3=2.64K
ON/OFF
Input
22uF
R4=1K
SD2
R2=1K
Anachip Corp.
www.anachip.com.tw
Rev.0B Dec.02, 2002
3/5
AP435/435L
Dual Linear Controller With Shutdown
( Preliminary )
Package Outline
(1) Plastic Dual-in-line Package:PDIP-8L
D
E1
E-PIN O0.118 NOTE 9
PIN #1 INDENT O0.025 DEEP 0.006-0.008
E
7 (4X)
A1
L
A
A2
15 (4X)
B
S
Symbols
A
A1
A2
B
B1
B2
C
D
E
E1
e
L
eB
S
e
B1
B2
C
eB
Dimensions in millimeters
Min.
Nom.
Max.
5.33
−
−
0.38
−
−
3.1
3.30
3.5
0.36
0.46
0.56
1.4
1.52
1.65
0.81
0.99
1.14
0.20
0.25
0.36
9.02
9.27
9.53
7.62
7.94
8.26
6.15
6.35
6.55
2.54
−
−
2.92
3.3
3.81
8.38
8.89
9.40
0.71
0.84
0.97
Anachip Corp.
www.anachip.com.tw
Dimensions in inches
Min.
Nom.
Max.
0.210
−
−
0.015
−
−
0.122
0.130
0.138
0.014
0.018
0.022
0.055
0.060
0.065
0.032
0.039
0.045
0.008
0.010
0.014
0.355
0.365
0.375
0.300
0.313
0.325
0.242
0.250
0.258
0.100
−
−
0.115
0.130
0.150
0.330
0.350
0.370
0.028
0.033
0.038
Rev.0B Dec.02, 2002
4/5
AP435/435L
Dual Linear Controller With Shutdown
( Preliminary )
E
H
(2) JEDEC Small Outline Package :SOP-8L
L
VIEW "A"
D
0.015x45
7 (4X)
C
A
A2
7 (4X)
B
VIEW "A"
A1
e
y
A
Dimensions in millimeters
MIN
NOM
MAX
1.40
1.60
1.75
A1
0.10
0.040
1.50
0.051
−
0.057
0.100
1.30
−
1.45
0.25
A2
B
0.33
0.41
0.51
0.013
0.016
0.020
C
0.19
0.20
0.25
0.0075
0.008
0.010
D
4.80
4.85
5.05
0.189
0.191
0.199
E
3.80
3.91
4.00
0.150
0.154
0.157
e
1.27
5.99
−
6.20
−
0.228
0.050
H
−
5.79
−
0.244
L
0.38
0.71
1.27
0.015
0.028
0.050
y
−
0O
−
0.10
−
−
8O
−
0O
0.004
−
8O
Symbols
θ
Anachip Corp.
www.anachip.com.tw
Dimensions in inches
MIN
NOM
MAX
0.055
0.063
0.069
0.236
0.059
Rev.0B Dec.02, 2002
5/5
Similar pages