May 15, 2007 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G (ITU-T Rec.G.984.2) Members of FlexonTM Family Standard Compliant with ITU-T G.984.2, G.984.2 Amendment 1 Compliant with FCC 47 CFR Part 15, Class B Compliant with FDA 21 CFR 1040.10 and 1040.11, Class I Description FTM-9423P(T)-K(F)GH(i)G is Optical Network Terminal (ONT) diplexer for 1244/2488M Class B+ application in Features Single ITU-T Rec.G.984.2 and G.984.2 Amendment 1. fiber bi-directional data links with asymmetric 1244Mbit/s upstream and 2488Mbit/s downstream Integrated with micro-optics WDM filter for dual wavelength Tx/Rx operation at 1310/1490nm The diplexers are the high performance modules for 1244/2488M data link in single fiber by using 1310nm burst mode transmitter and 1490nm continuous mode receiver with 1550nm optical signal rejection. Burst mode operation transmitter with 1310nm The transmitter section uses a multiple quantum well DFB laser 1310nm DFB laser, which is ClassⅠlaser compliant Power levelling mechanism(for 2×10 SFF) product according to international safety standard Continuous mode operation receiver with 1490nm IEC-60825. The receiver section uses an integrated high sensitivity APD-TIA with 1550nm optical 1490nm APD and preamplifier mounted in an optical signal rejection header and limiting post-amplifier IC. Different operating case temperature class 0 to 70℃ Standard Class -40 to 85℃ Industrial Class The optical burst output can be enabled by a LVTTL logic high-level input of TX_BRST. Signal Detected (SD) output is provided to indicate the detection of an input 2×5 and 2×10 SFF package SC/UPC or SC/APC connector Single 3.3V power supply The LVPECL data input interface and CML data output incorporated into the 2×10 SFF transceivers and allows interface real time access to the transceiver operating parameters LVTTL transmitter burst-mode control such as power supply, operating temperature, laser bias LVTTL receiver signal-detected indication current, receiver optical power by reading a built-in Low EMI and excellent ESD protection memory with I2C interface. Class I laser safety standard IEC-60825 compliant optical signal of receiver. Digital diagnostic monitoring interface Applications Gigabit-capable Passive Optical Networks(GPON) ONT with video-overlay Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 1 of 17 is SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e Regulatory Compliance The transceivers have been tested according to American and European product safety and electromagnetic compatibility regulations (See Table 1). For further information regarding regulatory certification, please refer to FlexonTM regulatory specification and safety guidelines, or contact with Fiberxon, Inc. America sales office listed at the end of documentation. Table 1 - Regulatory Compliance Feature Standard Electrostatic Discharge MIL-STD-883E (ESD) to the Electrical Pins Method 3015.7 Performance Class Ⅰ(>500 V) FCC Part 15 Class B Electromagnetic EN55022 Class B (CISPR 22B) Interference (EMI) Compliant with standards VCCI Class B Immunity IEC 61000-4-3 Compliant with standards FDA 21CFR 1040.10 and 1040.11 Laser Eye Safety EN60950, EN (IEC) 60825-1,2 Compliant with Class I laser product Component Recognition UL and CSA Compliant with standards RoHS 2002/95/EC 4.1&4.2 Compliant with standards Absolute Maximum Ratings Absolute Maximum Ratings are those values, beyond which, some damages may occur to the devices. Exposure to conditions above the Absolute Maximum Ratings listed in Table 2 may negatively impact the reliability of the products. Table 2 - Absolute Maximum Ratings Parameter Storage Ambient Temperature Operating Case Temperature (Note) Symbol Min. Max. Unit TSTG -40 85 °C 0 70 -40 85 TC °C Operating Humidity HOPR 5 95 % Power Supply Voltage VCC 0 4 V GND Vcc V Input Voltage Receiver Damaged Threshold 0 Soldering Temperature Bending Radius FTM-9423P(T)-K(F)GHG FTM-9423P(T)-K(F)GHiG dBm 260/10 30 Note °C/s mm Note: Refer to temperature testing area marked in Figure 6 Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 2 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e Recommended Operating Conditions Table 3 - Recommended Operating Conditions Parameter Symbol Min. Power Supply Voltage VCC Operating Case Temperature TC Operating Humidity Max. Unit 3.13 3.47 V 0 70 -40 85 5 95 HOPR Data Rate(Upstream/Downstream) Typ. 1244.16/2488.32 Consecutive Identical Digital Immunity Note 3.3V±5% FTM-9423P(T)-K(F)GHG °C FTM-9423P(T)-K(F)GHiG % Mbit/s 72 Bit Optical and Electrical Characteristics Table 4- Transmitter Optical and Electrical Characteristics FTM-9423P(T)-K(F)GHG (0°C <TC<70°C and 3.13V<VCC<3.47V) FTM-9423P(T)-K(F)GHiG (-40°C <TC<85°C and 3.13V<VCC<3.47V) Parameter Symbol Min. Optical Center Wavelength λC 1260 Optical Spectrum Width(-20dB) ∆λ Side Mode Suppression Ratio SMSR +0.5 POUT Average Launch Power (mode 2) Average Launch Power-OFF Transmitter Max. Unit 1360 nm 1 nm 2 +5 -2.5 +2 -5.5 -1 POFF -45 10 dBm ER Burst Turn On Time TON 12.8 dB ns Burst Turn Off Time TOFF 12.8 ns -10 dB Transmitter Reflectance Tolerance to Transmitter Incident Light Power -15 0.5 VIN 200 Common-Mode Input Voltage VCM Vcc-1.49 Input Differential Impedance ZIN 90 3 dB Compliant With ITU-T G984.2 Data Input Differential Swing 2 dB Optical Penalty Optical Eye Diagram 1 dBm Extinction Ratio Power Supply Current Note 30 Average Launch Power (mode 0) Average Launch Power (mode 1) Typ. 2,4 1600 mV Vcc-1.32 Vcc-VIN/4 V 100 110 Ω 250 mA Transmitter Burst Control Voltage - Low VBURST, L ICC_TX 0 0.8 V Transmitter Burst Control Voltage - High VBURST, H 2.0 VCC V 5 6 Note 1: Launched into 9/125um SMF, mode 1, 2 are implemented by power leveling mechanism in 2×10 SFF Note 2: Measured with PRBS 223-1 plus 72bits CID test pattern @1244.16Mbit/s, and the Bessel-Thompson filter is turned on. Note 3: Refer to Timing Parameter Definition in Burst Mode Sequence Note 4: Transmitter eye mask definition is shown as below. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 3 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e 1244.16Mbit/s x1/x4 0.22/0.78 x2/x3 0.40/0.60 y1/y4 0.17/0.83 y2/y3 0.20/0.80 Note 5: Compatible with LVPECL input (See Recommended Interface Circuit) Note 6: TX_BRST (See Pin Function Definitions) Table 5 - Receiver Optical and Electrical Characteristics FTM-9423P(T)-K(F)GHG (0°C <TC<70°C and 3.13V<VCC<3.47V) FTM-9423P(T)-K(F)GHiG (-40°C <TC<85°C and 3.13V<VCC<3.47V) Parameter Symbol Operating Wavelength Min. Typ. Max. Unit 1480 1490 1500 nm -31 -29 Sensitivity PSEN Overload POV Signal-Detected Assert Level PSDA Signal-Detected Deassert Level PSDD -39 PSDA- PSDD 0.5 Signal-Detected Hysteresis -7 -30 dBm 1 dBm 2 dBm 3 6 dB Tolerance to Reflected Optical Power 10 dB Receiver Reflectance -20 dB 150 mA Power Supply Current ICC_RX Data Output Differential Swing VOUT 400 1000 mV Signal-Detected Voltage - Low VSD, L 0 0.4 V Signal-Detected Voltage - High VSD, H 2.4 VCC V Signal-Detected Assert Time TASS 100 µs TDAS 100 µs Signal-Detected Deassert Time Notes 4 5 23 Note 1: Measured with PRBS 2 -1 plus 72bits CID test pattern @2488.32Mbit/s 1310nm, ER=10dB, BER =10-10 Note 2: An increase in optical power above the specified level will cause the Signal Detect output to switch from a low state to a high state. Note 3: A decrease in optical power below the specified level will cause the Signal Detect output to switch from a high state to a low state. Note 4: CML output, AC coupled internally, guaranteed in the full range of input optical power (See Recommended Interface Circuit) Note 5: SD (See Pin Function Definitions) Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 4 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e Optical Signal (1-Level) Optical Signal Output (at ONT side) Optical Signal (0-Level) Dark Level TON TOFF Upstream Data (TD+/TD- at ONT side) Tx_BRST (at ONT side) Figure 1 Timing Parameter Definition in Burst Mode Sequence Recommended Interface Circuit Figure 2 shows the recommended interface scheme for FTM-9423P(T)-FGH(i)G +3.3V VEET(7) 0.1µF 2 X 1µH 10µF 0.1µF FTM-9423P(T)-FGH(i)G VCCT(6) VCCR(2) 10µF PON_TX_DISABLE 0.1µF +3.3V 10K VEER(1) TX_BRST(8) +3.3V Z=50 TXP Z=50 TXN G-PON MAC 130 130 TD+(9) Laser Driver (BM) TD-(10) 82 SerDes 82 +3.3V 82 82 Z=50 RD-(4) Z=50 RD+(5) RXN RXP 130 LIA(CM) 130 +3.3V PON_LOS SD(3) 10K Figure 2 Recommended Interface Circuit for FTM-9423P(T)-FGH(i)G Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 5 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet Document Confidential Level: In public May. 15, 2007 Template ver. 1e Figure 3 shows the recommended interface scheme for FTM-9423P(T)-KGH(i)G Figure 3 Recommended Interface Circuit FTM-9423P(T)-KGH(i)G Pin Definitions 2×5/2×10 SFF planform in Figure 4 below shows the pin information of electrical interface and mounting studs. Functions are described in Table 6 and Table 7 with some accompanying notes. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 6 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet Document Confidential Level: In public May. 15, 2007 Template ver. 1e Figure 4 2×5/2×10 SFF Planform Table 6 - Pin Function Definitions (2x5 SFF) Pin No. Name Description 1 VEER Receiver Signal Ground 2 VCCR Receiver Power Supply 3 SD Receiver Signal-Detected Indication 4 RD- Inverted Receiver Data Output 5 RD+ Non-inverted Receiver Data Output 6 VCCT Transmitter Power Supply 7 VEET Transmitter Signal Ground 8 TX_BRST Transmitter Burst Control 9 TD+ Transmitter Non-inverted Data Input 10 TD- Transmitter Inverted Data Input F MS Mounting Studs Notes 1 2 3 4 5 Table 7 - Pin Function Definitions (2x10 SFF) Pin No. Name Description 1 NC 2 VEER Receiver Signal Ground 3 VEER Receiver Signal Ground 4 NC No Function Definition Not connected 5 NC No Function Definition Not connected 6 VEER Receiver Signal Ground 7 VCCR Receiver Power Supply 8 SD Receiver Signal-Detected Indication 9 RD- Inverted Receiver Data Output 10 RD+ Non-inverted Receiver Data Output 11 VCCT Transmitter Power Supply 12 VEET Transmitter Signal Ground 13 TX_BRST 14 TD+ Transmitter Non-inverted Data Input 15 TD- Transmitter Inverted Data Input 16 VEET Transmitter Signal Ground 17 SCL Clock Line of the I2C interface No Function Definition Transmitter Burst Control Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Notes Not connected 1 2 3 4 6 Page 7 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e 2 18 SDA Data Line of the I C interface 6 19 RESET Reset Input to Microprocessor 7 20 VEET Transmitter Signal Ground F MS Mounting Studs 5 Note 1: LVTTL logic output, with internal 10KΩ pull-up resistor. Optical Signal-Detected: High; Optical Signal Loss: Low Note 2: CML logic output, AC coupled internally. (See Recommended Interface Circuit) Note 3: A positive level enable optical signal output under burst mode. (See Timing Parameter Definition in Burst Mode Sequence) Note 4: Compatible with LVPECL input, DC coupled internally (See Recommended Interface Circuit) Note 5: The mounting studs are provided for transceiver mechanical attachment to circuit board. They may also provide an optional connection of the transceiver to the equipment chassis ground. The holes in the circuit board must be tied to chassis ground. It is not recommended that the mounting studs be connected to signal ground. Note 6: I2C interface, they should be pulled up with two 4.7-10KΩ resistors on the host board. Note 7: LVTTL reset input to microprocessor, with internal 10KΩ pull-up resistor, active low. Mechanical Design Diagram The form factor is 2×5/2×10 SFF with pigtail fiber. The pigtail fiber length is 520 - 550mm and its minimum bending radius is 30mm. The fiber connector type is SC/UPC or SC/APC. The mechanical design diagram is shown in Figure 5 and Figure 6. (Dimension in mm) 19.56 24.89 10.16 5.11±0.05 3.7±0.1 2.85±0.3 520~550 2- 1 1.778 Max40mm 4X1.778(=7.112) 49.56±0.1 11.38±0.5 13.4±0.1 4.8±0.3 0.9 12.75±0.1 0 0 10- 0.50 -0.05 Label Case Temperature Testing Point Figure 5 Mechanical Design Diagram (2x5 SFF) Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 8 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e 19.56 16.89 10.16 13.11±0.05 3.7±0.1 4.8±0.3 0.9 12.75±0.1 0 0 20- 0.45 -0.05 2.85±0.3 520~550 2- 1 1.778 Max40mm 9X1.778(=16.002) 11.38±0.5 13.4±0.1 49.56±0.1 Label Case Temperature Testing Point Figure 6 Mechanical Design Diagram (2x10 SFF) Table 8 - Pigtail Fiber Characteristics Parameter Min. Mode Field Diameter Cladding Diameter Jacket Diameter Typical Max. 9 µm 125 µm 0.9 Bending Radius of Pigtail Fiber Unit mm 30 mm Tension Force on Pigtail Fiber 1 Kg 550 mm Pigtail Fiber Length 520 Optical Return Loss (UPC type) -1310nm 50 dB Optical Return Loss (APC type) -1310nm 60 dB Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 9 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e EEPROM Information The SFF-8472 defines a 256-byte memory map in EEPROM describing the transceiver’s capabilities, standard interfaces, manufacture, and other information, which is accessible over 2 wire interface at the 8-bit address 1010000X(A0h). The memory contents refer to Table 9. Table 9 - EEPROM Serial ID Memory Contents (A0h) Addr. Field Size (Bytes) Name of Field Hex Description 0 1 Identifier 02 SFF Tranceiver 1 1 Ext. Identifier 04 MOD4 2 1 Connector 0B Optical pigtail 3-10 8 Transceiver XX XX XX XX XX XX XX XX (Transmitter Code, not defined for GPON) 11 1 Encoding 03 NRZ 12 1 BR, Nominal 0C 1.244Gbps transmission 13 1 Reserved 00 14 1 Length (9um)-km 14 20(km) 15 1 Length (9um) C8 200(100m) 16 1 Length (50um) 00 Not Support MMF 17 1 Length (62.5um) 00 Not Support MMF 18 1 Length (Copper) 00 Not Support Copper 19 1 Reserved 00 20-35 16 Vendor name 36 1 Reserved 37-39 3 Vendor OUI 46 49 42 45 52 58 4F 4E 20 49 4E 43 2E 20 20 20 00 00 00 00 46 54 4D 39 34 32 33 50(54) 40-55 16 Vendor PN “FIBERXON INC.” (ASCII) 4B(46) 47 48 47 20 20 20 20 46 54 4D 39 34 32 33 50(54) 4B(46) 47 48 69 47 20 20 20 “FTM-9423P(T)-K(F)GHG” (ASCII) “FTM-9423P(T)-K(F)GHiG” (ASCII) 56-59 4 Vendor Rev XX XX 20 20 ASCII(“31 30 20 20” means 1.0 Revision) 60-61 2 Wavelength 05 1E 1310nm Laser Wavelength 62 1 Reserved 00 63 1 CC_BASE XX Check sum of byte 0-62 64-65 2 Options 00 06 SD,LAS_FAIL and TX_DISABLE 66 1 BR, max 00 67 1 BR, min 00 68-83 16 Vendor SN 84-91 8 Date code XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX XX 20 20 ASCII Year(2 bytes),Month(2 bytes),Day(2 bytes) Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 10 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e Compliant with SFF-8472 V9.5 92 1 Diagnostic Monitoring Type Internally Calibrated 68 Received power measurement type -Average Power 93 1 Enhanced Options 94 1 95 1 CC_EXT 96-255 164 Vendor Specific SFF-8472 Compliance 80 Diagnostics (Optional Alarm/warning flags) 02 Diagnostics Compliance(SFF-8472 V9.5) XX Check sum of byte 64-94 Monitoring Specification The digital diagnostic monitoring interface defines 256 bytes memory map in EEPROM, which makes use of the 8 bit address 1010001X(A2h). Please see Figure 7. Table 10~12 show the EEPROM definition from 0 to 119 byte, please refer to the SFF-8472 Rev 9.5 for the data format of these tables. The monitoring specification of this product is described in Table 13. Figure 7 EEPROM Memory Map Specific Data Field Descriptions Table 10 - EEPROM Serial ID Memory of the Alarm and Warning Thresholds Contents in A2h Addr. Field Size (Bytes) Name of Field Hex Description 00-01 2 Temp High Alarm XX XX Based on difference operation case 02-03 2 Temp Low Alarm XX XX temperature class product 04-05 2 Temp High Warning XX XX Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 11 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e 06-07 2 Temp Low Warning XX XX 08-09 2 Voltage High Alarm 94 70 3.8 V 10-11 2 Voltage Low Alarm 6D 60 2.8 V 12-13 2 Voltage High Warning 8C A0 3.6 V 14-15 2 Voltage Low Warning 75 30 3.0 V 16-17 2 Bias High Alarm 75 30 60 mA 18-19 2 Bias Low Alarm 05 DC 3 mA 20-21 2 Bias High Warning 61 A8 50 mA 22-23 2 Bias Low Warning 07 D0 4 mA 24-31 8 Reserved 00 00 32-33 2 RX Power High Alarm 0F 8D -4dBm 34-35 2 RX Power Low Alarm 00 0A -30dBm 36-37 2 RX Power High Warning 0C 5A -5dBm 38-39 2 RX Power Low Warning 00 0C -29dBm 40-55 24 Reserved 00 00 0 Table 11 - EEPROM Serial ID Memory of the Calibration Constants Contents in A2h Addr. Field Size (Bytes) Name of Field Hex Description 56-59 4 Rx_PWR(4) 00 00 00 00 0 60-63 4 Rx_PWR(3) 00 00 00 00 0 64-67 4 Rx_PWR(2) 00 00 00 00 0 68-71 4 Rx_PWR(1) 3F 80 00 00 1 72-75 4 Rx_PWR(0) 00 00 00 00 0 76-77 2 Tx_I(Slope) 01 00 1 78-79 2 Tx_I(Offset) 00 00 0 80-81 2 Tx_PWR(Slope) 01 00 1 82-83 2 Tx_PWR(Offset) 00 00 0 84-85 2 T (Slope) 01 00 1 86-87 2 T (Offset) 00 00 0 88-89 2 V (Slope) 01 00 1 90-91 2 V (Offset) 00 00 0 92-94 3 Reserved 00 00 00 0 95 1 Checksum XX Check sum of byte 0-94 Table 12 - EEPROM Serial ID Memory of the A/D Values and Status Bits Contents in A2h Addr. Bit Name of Field Hex 96-97 7-0 Temperature XX XX 98-99 7-0 VCC XX XX 100-101 7-0 TX Bias XX XX 102-103 7-0 Reserved XX XX Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Description Page 12 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e 104-105 7-0 RX Power XX XX 106-109 7-0 Reserved 00 00 00 00 110 7 TX Disable State 110 6 Soft TX Disable 110 5~3 Reserved 110 2 TX Fault 110 1 LOS 110 0 Data_Ready_Bar 111 7-2 Reserved 111 1-0 Power leveling control 0 XX 00 0 00 00 for the power levelling mode 0 01 01 for the power levelling mode 1 10 10 for the power levelling mode 2 112 7 Temp High Alarm 112 6 Temp Low Alarm 112 5 VCC High Alarm 112 4 VCC Low Alarm 112 3 TX Bias High Alarm 112 2 TX Bias Low Alarm 112 1-0 Reserved 113 7 RX Power High Alarm 113 6 RX Power Low Alarm 113 5-0 Reserved “000000” 0 114-115 7-0 Reserved 00 00 0 116 7 Temp High Warning 116 6 Temp Low Warning 116 5 VCC High Warning 116 4 VCC Low Warning 116 3 TX Bias High Warning 116 2 TX Bias Low Warning 116 1-0 Reserved 117 7 RX Power High Warning 117 6 RX Power Low Warning 117 5-0 Reserved “000000” 0 118-119 0-7 Reserved 00 00 0 XX XX Note: The “XX” byte should be filled in according to practical case. For more information, please refer to the related document of SFF-8472 Rev 9.5. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 13 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e Table 13- Monitoring Specification Parameter Range Accuracy Calibration -40 to 100°C ±3°C Internal Voltage 3.0 to 3.6V ±3% Internal Bias Current 0 to 100mA ±10% Internal -30 to -4dBm ±3dB Internal Temperature RX Power Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 14 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet Document Confidential Level: In public May. 15, 2007 Template ver. 1e Ordering Information Part No. Product Description 1310nm(TX)/1490nm(RX), SC/UPC Pigtailed 2×5 SFF for GPON ONT 1244/2488M FTM-9423P-FGHG Class B+ application, 0°C ~ 70°C, RoHS compliance 1310nm(TX)/1490nm(RX), SC/UPC Pigtailed 2×5 SFF for GPON ONT 1244/2488M FTM-9423P-FGHiG Class B+ application, -40°C ~ 85°C, RoHS compliance 1310nm(TX)/1490nm(RX), SC/UPC Pigtailed 2×10 SFF for GPON ONT 1244/2488M FTM-9423P-KGHG Class B+ application, power levelling supported, 0°C ~ 70°C, RoHS compliance 1310nm(TX)/1490nm(RX), SC/UPC Pigtailed 2×10 SFF for GPON ONT 1244/2488M FTM-9423P-KGHiG Class B+ application, power levelling supported, -40°C ~ 85°C, RoHS compliance 1310nm(TX)/1490nm(RX), SC/APC Pigtailed 2×5 SFF for GPON ONT 1244/2488M FTM-9423T-FGHG Class B+ application, 0°C ~ 70°C, RoHS compliance 1310nm(TX)/1490nm(RX), SC/APC Pigtailed 2×5 SFF for GPON ONT 1244/2488M FTM-9423T-FGHiG Class B+ application, -40°C ~ 85°C, RoHS compliance 1310nm(TX)/1490nm(RX), SC/APC Pigtailed 2×10 SFF for GPON ONT 1244/2488M FTM-9423T-KGHG Class B+ application, power levelling supported, 0°C ~ 70°C, RoHS compliance 1310nm(TX)/1490nm(RX), SC/APC Pigtailed 2×10 SFF for GPON ONT 1244/2488M FTM-9423T-KGHiG Class B+ application, power levelling supported, -40°C ~ 85°C, RoHS compliance Related Documents For further information, please refer to the following documents: ITU-T G.984.2 ITU-T G.984.2. Amendment 1 Obtaining Document You can visit our website: http://www.fiberxon.com/ Or contact with Fiberxon, Inc. America Sales Office listed at the end of documentation to get the latest documents. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 15 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet May. 15, 2007 Document Confidential Level: In public Template ver. 1e Revision History Reversion Initiate Review Approve Pre 1a Gary Chen Peter Tang Peter Tang Subject Initial datasheet(temporary version) (Doc No. DS0000002-1a) Release Date Jul. 7, 2006 Revised Datasheet Pre.1b Gary Chen Peter Tang Peter Tang 1. Modify the pin definition 2. Update Figure 3 Aug. 7, 2006 (Doc No. DS0000002-1b) Revised Datasheet: Pre.1c Gary Chen Peter Tang Peter Tang 1. Added the module figure Sep. 26, 2006 2. Modify the order information Revised Datasheet: 1. Pre.1d Jacob Cai Gary Chen Peter Tang Update the value of overload in Table 4 from -5dBm to -7dBm 2. May 15, 2007 Delete FTM-9423P(T)-K(F)GHEG. (Doc No. DS0000002-1d) Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 16 of 17 SFF GPON ONT Diplexer FTM-9423P(T)-K(F)GH(i)G Class B+ attenuation range: 13-28dB Preliminary Data Sheet Document Confidential Level: In public May. 15, 2007 Template ver. 1e © Copyright Fiberxon Inc. 2007 All Rights Reserved. All information contained in this document is subject to change without notice. The products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change Fiberxon’s product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of Fiberxon or third parties. All information contained in this document was obtained in specific environments, and is presented as an illustration. The results obtained in other operating environment may vary. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN ”AS IS” BASIS. In no event will Fiberxon be liable for damages arising directly from any use of the information contained in this document. Contact U.S.A. Headquarters: 5201 Great America Parkway, Suite 340 Santa Clara, CA 95054 U. S. A. Tel: 408-562-6288 Fax: 408-562-6289 Or visit our website: http://www.fiberxon.com/ Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Page 17 of 17