Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type Data Sheet 1 Common Mode Choke Coil Wire Wound Type DLW21H Series (0805 Size) c Dimensions c Impedance-Frequency Characteristics (Main Items) DLW21HN181SQ2 (0.17) DLW21HN121SQ2 2.0±0.2 (0.45) 1.2±0.2 (0.45) DLW21HN900SQ2 100 DLW21HN670SQ2 10 (2) DLW21HN181SQ2 (0.4) (1) Common mode 1000 Impedance (Ω) 0.9±0.1 10000 DLW21HN121SQ2 1 DLW21HN900SQ2 (0.4) Differential mode (4) DLW21HN670SQ2 0.1 : Electrode 1 (3) 10 100 1000 Frequency (MHz) (in mm) c Impedance-Frequency Characteristics (Main Items) c Equivalent Circuit 10000 Common mode Impedance (Ω) 1000 DLW21HN121HQ2 DLW21HN900HQ2 100 (1) (2) (4) (3) DLW21HN670HQ2 10 1 DLW21HN121HQ2 DLW21HN900HQ2 DLW21HN670HQ2 0.1 1 10 Differential mode No polarity. 100 1000 Frequency (MHz) c Differential Mode Transmission Characteristics (Typ.) 0 DLW21HN670HQ2 DLW21HN900HQ2 DLW21HN121HQ2 Insertion Loss (dB) 2 c Packaging Code Packaging Minimum Quantity L 180mm Embossed Tape 3000 B Bulk(Bag) 500 4 6 8 10 1 10 100 Frequency (MHz) 1000 10000 Continued on the following page. oThis data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.3.7 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Wire Wound Type Data Sheet 2 Continued from the preceding page. c Rated Value (p: packaging code) Operating Temperature Range Part Number Common Mode Impedance (at 100MHz/20°C) DLW21HN670SQ2p 67ohm ±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. DLW21HN900SQ2p 90ohm ±25% 330mA 50Vdc 10M ohm 125Vdc 0.35ohm max. -40 to +85°C DLW21HN121SQ2p 120ohm ±25% 280mA 50Vdc 10M ohm 125Vdc 0.45ohm max. -40 to +85°C DLW21HN181SQ2p 180ohm ±25% 250mA 50Vdc 10M ohm 125Vdc 0.50ohm max. -40 to +85°C DLW21HN670HQ2p 67ohm ±25% 240mA 20Vdc 10M ohm 50Vdc 0.49ohm max. -40 to +85°C DLW21HN900HQ2p 90ohm ±25% 220mA 20Vdc 10M ohm 50Vdc 0.59ohm max. -40 to +85°C DLW21HN121HQ2p 120ohm ±25% 200mA 20Vdc 10M ohm 50Vdc 0.68ohm max. -40 to +85°C Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance -40 to +85°C Number of Circuit: 1 c !Caution/Notice !Caution (Rating) Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. oThis data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. !Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2013.3.7 http://www.murata.com/