ON LMV981 Single and dual low voltage, rail-to-rail input and output, operational amplifiers with shutdown Datasheet

LMV981, LMV982
Single and Dual Low
Voltage, Rail-to-Rail Input
and Output, Operational
Amplifiers with Shutdown
The LMV981 Single and LMV982 Dual are low−voltage
operational amplifiers which can operate on single−sided power
supplies (1.8 V to 5.0 V) with rail−to−rail input and output swing.
Both devices come in small state−of−the−art packages and require
very low quiescent current making them ideal for battery−operated,
portable applications such as notebook computers and hand−held
instruments. Rail−to−Rail operation allows for optimal
signal−to−noise applications plus the small packages allow for closer
placement to signal sources further enhancing overall signal chain
performance.
The LMV981 Single and LMV982 Dual both have a shutdown pin
that can be used to disable the device and further reduce power
consumption. Shutdown is implemented by driving the SHDN Pin LOW.
Features
• Specified at Single−Sided Power Supply: 1.8 V, 2.7 V, and 5 V
• Small Packages:
•
•
•
•
•
LMV981 in a SC−70 and uLLGA (1.5mm x 1.5mm x 0.4mm)
LMV982 in a Micro10 and uQFN (1.4mm x 1.8mm x 0.6 mm)
No Output Crossover Distortion
Extended Industrial Temperature Range: −40°C to +125°C
Low Quiescent Current 210 mA, max per channel
No Output Phase−Reversal from Overdriven Input
These are Pb−Free Devices
http://onsemi.com
MARKING
DIAGRAMS
LMV981 (Single)
6
1
SC−70
CASE 419B
1
AE MG
G
1
ULLGA8
CASE 613AG
M = Date Code
G
= Pb−Free Package
(Note: Microdot may be in either location)
LMV982 (Dual)
V982
AYW
• Notebook Computers, Portable Battery−Operated Instruments, PDA’s
• Active Filters, Supply−Current Monitoring
0.1
1
UQFN10
CASE 488AT
RL = 600 W
TA = 25°C
0.09
0.08
DV FROM RAIL (V)
1
Micro10
CASE 846B
Typical Applications
DE MG
G
A
= Assembly Location
Y
= Year
W = Work Week
G
= Pb−Free Package
(Note: Microdot may be in either location)
0.07
0.06
0.05
0.04
VOH
0.03
0.02
ORDERING INFORMATION
VOL
0.01
0 1.8
AAE MG
G
2.2
2.6
3
See detailed ordering and shipping information in the package
dimensions section on page 17 of this data sheet.
3.4
3.8
4.2
4.6
5
SUPPLY VOLTAGE (mV)
Figure 1. Output Voltage Swing vs. Supply Voltage
© Semiconductor Components Industries, LLC, 2010
February, 2010 − Rev. 5
1
Publication Order Number:
LMV981/D
LMV981, LMV982
PIN CONNECTIONS
SC70−6
1
NC
VCC
+IN
2
VEE
3
+
−
Micro10
ULLGA8/QFN
6
IN−
5
SHDN
IN+
4
−IN
OUT
VEE
8
1
2
7
+
−
3
IN A−
2
IN A+
3
VEE
4
7 IN B+
5
6 SHDN B
(Top View)
SHDN A
UQFN10
SHDN A
8
SHDN B
9
+INB
10
6
−
+
+
−
1
9 OUT B
B
+ −
8 IN B−
(Top View)
+INA
7
A
− +
VCC
5
NC − No internal connection
VEE
10 VCC
SHDN
NC
(Top View)
1
OUT
6
4
OUT A
5
−INA
4
OUTA
3
VCC
2
−INB
OUTB
(Top View)
MAXIMUM RATINGS
Symbol
VS
Rating
Supply Voltage (Operating Range VS = 2.7 V to 5.5 V)
Value
Unit
5.5
V
V
VIDR
Input Differential Voltage
$Supply Voltage
VICR
Input Common Mode Voltage Range
−0.5 to (V+) + 0.5
V
10
mA
Maximum Input Current
tSo
Output Short Circuit (Note 1)
Continuous
TJ
Maximum Junction Temperature (Operating Range −40°C to 85°C)
150
°C
qJA
Thermal Resistance
280
340
200
300
°C/W
Tstg
Storage Temperature (SOT23−6)
−65 to 150
°C
260
°C
SC−70
ULLGA8
Micro10
UQFN10
Mounting Temperature (Infrared or Convection −30 sec)
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may
affect device reliability.
ESD data available upon request.
1. Continuous short−circuit operation to ground at elevated ambient temperature can result in exceeding the maximum allowed junction
temperature of 150°C. Output currents in excess of 45 mA over long term may adversely affect reliability. Shorting output to either V+
or V− will adversely affect reliability.
http://onsemi.com
2
LMV981, LMV982
1.8 V DC ELECTRICAL CHARACTERISTICS Unless otherwise noted, all min/max limits are guaranteed for TA = 25°C,
V+ = 1.8 V, V− = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm.
Parameter
Input Offset Voltage
Input Offset Voltage
Average Drift
Symbol
Condition
VIO
Min
Typ
Max
Unit
LMV981 (Single) (−40°C to +125°C)
1
6
mV
LMV982 (Dual) (−40°C to +125°C)
1
7.5
TCVIO
5.5
mV/°C
Input Bias Current
(Note 2)
IB
−40°C to +125°C
<1
nA
Input Offset Current
(Note 2)
IIO
−40°C to +125°C
<1
nA
Supply Current
(per Channel)
ICC
In Active Mode
75
−40°C to +125°C
205
In Shutdown: LMV981 (Single)
1.0
−40°C to +125°C
2.0
In Shutdown: LMV982 (Dual)
3.5
−40°C to +125°C
Common Mode
Rejection Ratio
Power Supply
Rejection Ratio
Input Common−Mode
Voltage Range
Large Signal Voltage
Gain LMV981
(Single) (Note 2)
CMRR
PSRR
VCM
AV
Output Swing
40
− 40°C to +125°C
40
−0.2 V v VCM v 0 V, 1.8 V v VCM v 2 V
40
1.8 V v
V+
v 5 V, VCM = 0.5 V
50
dB
70
50
For CMRR w 50 dB and TA = 25°C
V−
− 0.2
For CMRR w 50 dB and TA = − 40°C to +85°C
V−
V+
For CMRR w 50 dB and TA = − 40°C to +125°C
V−
+ 0.2
V+
− 0.2
RL = 600 W to 0.9 V, VO = 0.2 V to 1.6 V, VCM = 0.5 V
77
−40°C to +125°C
73
RL = 2 kW to 0.9V, VO = 0.2 V to 1.6 V, VCM = 0.5 V
80
75
75
−40°C to +125°C
72
RL = 2 kW to 0.9 V, VO = 0.2 V to 1.6 V,VCM = 0.5 V
78
−40°C to +125°C
75
VOH
RL = 600 W to 0.9V, VIN = $100 mV
1.65
−40°C to +125°C
1.63
VOL
RL = 600 W to 0.9V, VIN = $100 mV
−0.2
to 2.1
−40°C to +125°C
1.74
−40°C to +125°C
2. Guaranteed by design and/or characterization.
http://onsemi.com
3
dB
90
100
V
1.72
0.105
0.12
1.75
V
105
0.077
RL = 2 kW to 0.9V, VIN = $100 mV
RL = 2 kW to 0.9 V, VIN = $100 mV
V+
+ 0.2
101
−40°C to +125°C
VOL
dB
−40°C to +125°C
−40°C to +125°C
VOH
mA
5.0
0 V v VCM v 0.6 V, 1.4 V v VCM v 1.8 V
RL = 600 W to 0.9 V, VO = 0.2 V to 1.6 V, VCM = 0.5 V
Large Signal Voltage
Gain LMV982 (Dual)
(Note 2)
185
1.77
0.24
0.035
0.04
LMV981, LMV982
1.8 V DC ELECTRICAL CHARACTERISTICS Unless otherwise noted, all min/max limits are guaranteed for TA = 25°C,
V+ = 1.8 V, V− = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm.
Parameter
Output Short Circuit
Current
Shutdown Enable
Control
Symbol
Condition
Min
Typ
IO
Sourcing, Vo = 0 V, VIN = +100 mV
4.0
30
−40°C to +125°C
3.3
Sinking, Vo = 1.8V, VIN = −100 mV
7.0
−40°C to +125°C
5.0
VSHDN
Max
Unit
mA
60
Turn−on Voltage to Enable Device
1.0
Turn−off Voltage to Shutdown Device
0.55
V
2. Guaranteed by design and/or characterization.
1.8V AC ELECTRICAL CHARACTERISTICS Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 1.8 V,
V− = 0 V, VCM = 2.0 V,Vo = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm. Min/Max
specifications are guaranteed by testing, characterization, or statistical analysis.
Parameter
Slew Rate
Symbol
Condition
SR
(Note 3)
Min
Typ
Max
Unit
0.35
V/mS
GBWP
1.4
MHz
Phase Margin
Qm
67
°
Gain Margin
Gm
7
dB
Input−Referred
Voltage Noise
en
f = 50 kHz, VCM = 0.5 V
60
nV/√Hz
Total Harmonic
Distortion
THD
f = 1 kHz, AV = +1, RL = 600 W, VO = 1 VPP
0.023
%
(Note 4)
123
dB
Gain Bandwidth
Product
Amplifier−to−Amplifier
Isolation
3. Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates.
4. Input referred, RL = 100 kW connected to V+/2. Each amp excited in turn with 1 kHz to produce VO = 3 VPP. (For Supply Voltages < 3 V,
VO = V+).
http://onsemi.com
4
LMV981, LMV982
2.7V DC ELECTRICAL CHARACTERISTICS Unless otherwise noted, all min/max limits are guaranteed for TA = 25°C,
V+ = 2.7 V, V− = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm.
Parameter
Input Offset Voltage
Input Offset Voltage
Average Drift
Symbol
Condition
VIO
Min
Typ
Max
Unit
LMV981 (Single) (−40°C to +125°C)
1
6
mV
LMV982 (Dual) (−40°C to +125°C)
1
7.5
TCVIO
5.5
mV/°C
Input Bias Current
(Note 5)
IB
−40°C to +125°C
<1
nA
Input Offset Current
(Note 5)
IIO
−40°C to +125°C
<1
nA
Supply Current (per
Channel)
ICC
In Active Mode
80
−40°C to +125°C
210
In Shutdown: LMV981 (Single)
1.0
−40°C to +125°C
2.0
In Shutdown: LMV982 (Dual)
3.5
−40°C to +125°C
Common Mode
Rejection Ratio
Power Supply
Rejection Ratio
Input Common−Mode
Voltage Range
Large Signal Voltage
Gain LMV981
(Single) (Note 5)
Large Signal Voltage
Gain LMV982 (Dual)
(Note 5)
Output Swing
CMRR
PSRR
VCM
AV
50
−40°C to +125°C
50
−0.2 V v VCM v 0 V, 2.7 V v VCM v 2.9 V
50
70
50
70
1.8 V v
V+
v 5 V, VCM = 0.5 V
dB
50
For CMRR w 50 dB and TA = 25°C
V−
− 0.2
For CMRR w 50 dB and TA = −40°C to +85°C
V−
V+
For CMRR w 50 dB and TA = −40°C to +125°C
V−
+ 0.2
V+
− 0.2
RL = 600 W to 1.35 V, VO = 0.2 V to 2.5 V
87
−40°C to +125°C
86
RL = 2 kW to 1.35 V, VO = 0.2 V to 2.5 V
92
91
78
−40°C to +125°C
75
RL= 2 kW to 1.35 V, VO = 0.2 V to 2.5 V
81
−40°C to +125°C
78
VOH
RL = 600 W to 1.35 V, VIN = $100 mV
2.55
−40°C to +125°C
2.53
VOL
RL = 600 W to 1.35 V, VIN = $100 mV
−0.2
to 3.0
−40°C to +125°C
2.64
−40°C to +125°C
5. Guaranteed by design and/or characterization.
http://onsemi.com
5
dB
90
100
V
2.62
0.11
0.13
2.65
V
110
0.083
RL = 2 kW to 1.35 V, VIN = $100 mV
RL = 2 kW to 1.35 V, VIN = $100 mV
V+
+ 0.2
104
−40°C to +125°C
VOL
dB
70
−40°C to +125°C
−40°C to +125°C
VOH
mA
5.0
0 V v VCM v 1.5 V, 2.3 V v VCM v 2.7 V
RL = 600 W to 1.35 V, VO = 0.2 V to 2.5 V
AV
190
2.675
0.025
0.04
0.045
LMV981, LMV982
2.7V DC ELECTRICAL CHARACTERISTICS Unless otherwise noted, all min/max limits are guaranteed for TA = 25°C,
V+ = 2.7 V, V− = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm.
Parameter
Output Short Circuit
Current
Shutdown Enable
Control
Symbol
Condition
Min
Typ
IO
Sourcing, Vo = 0 V, VIN = $100 mV
20
65
−40°C to +125°C
15
Sinking, Vo = 0 V, VIN = −100 mV
18
−40°C to +125°C
12
VSHDN
Max
Unit
mA
75
Turn−on Voltage to Enable Device
1.9
Turn−off Voltage to Shutdown Device
0.55
V
5. Guaranteed by design and/or characterization.
2.7V AC ELECTRICAL CHARACTERISTICS Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 2.7 V,
V− = 0 V, VCM = 2.0V ,Vo = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm. Min/Max
specifications are guaranteed by testing, characterization, or statistical analysis.
Parameter
Slew Rate
Symbol
Condition
SR
(Note 6)
Min
Typ
Max
Unit
0.4
V/uS
GBWP
1.4
MHz
Phase Margin
Qm
70
°
Gain Margin
Gm
7.5
dB
Input−Referred
Voltage Noise
en
f = 50 kHz, VCM = 1.0 V
57
nV/√Hz
Total Harmonic
Distortion
THD
f = 1 kHz, AV = +1, RL = 600 W, VO = 1 VPP
0.022
%
(Note 7)
123
dB
Gain Bandwidth
Product
Amplifier−to−Amplifier
Isolation
6. Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates.
7. Input referred, RL = 100 kW connected to V+/2. Each amp excited in turn with 1 kHz to produce VO = 3 VPP. (For Supply Voltages < 3 V,
VO = V+).
http://onsemi.com
6
LMV981, LMV982
5V DC ELECTRICAL CHARACTERISTICS Unless otherwise noted, all min/max limits are guaranteed for TA = 25°C, V+ = 5 V,
V− = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm.
Parameter
Input Offset Voltage
Input Offset Voltage
Average Drift
Symbol
Condition
VIO
Min
Typ
Max
Unit
LMV981 (Single) (−40°C to +125°C)
1
6
mV
LMV982 (Dual) (−40°C to +125°C)
1
7.5
TCVIO
5.5
mV/°C
Input Bias Current
(Note 8)
IB
−40°C to +125°C
<1
nA
Input Offset Current
(Note 8)
IIO
−40°C to +125°C
<1
nA
Supply Current (per
Channel)
ICC
In Active Mode
95
−40°C to +125°C
230
In Shutdown: LMV981 (Single)
1.0
−40°C to +125°C
2.0
In Shutdown: LMV982 (Dual)
3.5
−40°C to +125°C
Common−Mode
Rejection Ratio
Power Supply
Rejection Ratio
Input Common−Mode
Voltage Range
Large Signal Voltage
Gain LMV981
(Single) (Note 8)
Large Signal Voltage
Gain LMV982 (Dual)
(Note 8)
Output Swing
CMRR
PSRR
VCM
AV
50
−40°C to +125°C
50
−0.2 V v VCM v 0 V, 5.0 V v VCM v 5. 2V
50
70
50
70
1.8 V v
V+
v 5 V, VCM = 0.5 V
dB
50
For CMRR w 50 dB and TA = 25°C
V−
− 0.2
For CMRR w 50 dB and TA = −40°C to +85°C
V−
V+
For CMRR w 50 dB and TA = −40°C to +125°C
V−
+ 0.3
V+
− 0.3
RL = 600 W to 2.5 V, VO = 0.2 V to 4.8 V
88
−40°C to +125°C
87
RL = 2 kW to 2.5 V, VO = 0.2 V to 4.8 V
94
93
81
−40°C to +125°C
78
RL = 2 kW to 2.5 V, VO = 0.2 V to 4.8 V
85
−40°C to +125°C
82
VOH
RL = 600 W to 2.5 V, VIN = $100 mV
4.855
−40°C to +125°C
4.835
VOL
RL = 600 W to 2.5 V, VIN = $100 mV
−0.2
to 5.3
−40°C to +125°C
4.935
−40°C to +125°C
8. Guaranteed by design and/or characterization.
http://onsemi.com
7
dB
90
100
V
4.89
0.16
0.18
4.945
V
113
0.12
RL = 2 kW to 2.5 V, VIN = $100 mV
RL = 2 kW to 2.5 V, VIN = $100 mV
V+
+ 0.2
102
−40°C to +125°C
VOL
dB
70
−40°C to +125°C
−40°C to +125°C
VOH
mA
5.0
0 V v VCM v 3.8 V, 4.6 V v VCM v 5.0 V
RL = 600 W to 2.5 V, VO = 0.2 V to 4.8 V
AV
210
4.967
0.037
0.065
0.075
LMV981, LMV982
5V DC ELECTRICAL CHARACTERISTICS Unless otherwise noted, all min/max limits are guaranteed for TA = 25°C, V+ = 5 V,
V− = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm.
Parameter
Output Short−Circuit
Current
Shutdown Enable
Control
Symbol
Condition
Min
Typ
IO
Sourcing, Vo = 0 V, VIN = +100 mV
55
65
−40°C to +125°C
45
Sinking, Vo = 5 V, VIN = −100 mV
58
−40°C to +125°C
45
VSHDN
Max
Unit
mA
80
Turn−on Voltage to Enable Device
4.2
Turn−off Voltage to Shutdown Device
0.55
V
8. Guaranteed by design and/or characterization.
5V AC ELECTRICAL CHARACTERISTICS Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 5 V, V− =
0 V, VCM = 2.0 V,Vo = V+/2 and RL > 1 MW. Typical specifications represent the most likely parametric norm.
Parameter
Slew Rate
Symbol
Condition
SR
(Note 9)
Min
Typ
Max
Unit
0.48
V/uS
GBWP
1.5
MHz
Phase Margin
Qm
65
°
Gain Margin
Gm
8
dB
Input−Referred
Voltage Noise
en
f = 50 kHz, VCM = 2 V
50
nV/√Hz
Total Harmonic
Distortion
THD
f = 1 kHz, AV = +1, RL = 600 W, VO = 1 VPP
0.022
%
(Note 10)
123
dB
Gain Bandwidth
Product
Amplifier−to−
Amplifier Isolation
9. Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates.
10. Input referred, RL = 100 kW connected to V+/2. Each amp excited in turn with 1 kHz to produce VO = 3 VPP. (For Supply Voltages < 3 V,
VO = V+).
http://onsemi.com
8
LMV981, LMV982
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
100
0.12
LMV981 (Single)
OUTPUT CURRENT (mA)
SUPPLY CURRENT (mA)
VCC = 5.0 V
25°C
0.1
0.08
125°C
−40°C
0.06
0.04
0.02
0
1.8
2.2
2.6
3
3.4
3.8
4.2
4.6
10
1
VCC = 1.8 V
0.1
0.01
0.001
5
0.01
0.1
1.0
10
SUPPLY VOLTAGE (V)
OUTPUT VOLTAGE REFERENCED TO VCC (mV)
Figure 2. Supply Current vs. Supply Voltage
Figure 3. Sourcing Current vs. Output Voltage
(TA = 255C)
0.1
100
RL = 600 W
TA = 25°C
0.09
VCC = 2.7 V
0.08
DV FROM RAIL (V)
VCC = 5.0 V
10
VCC = 1.8 V
1
0.1
0.07
0.06
0.05
0.04
VOH
0.03
0.02
0.01
0.01
0.001
0.01
0.1
1.0
0
10
VOL
1.8
2.2
2.6
3
3.4
3.8
4.2
4.6
OUTPUT VOLTAGE REFERENCED TO VEE (mV)
SUPPLY VOLTAGE (mV)
Figure 4. Sinking Current vs. Output Voltage
(TA = 255C)
Figure 5. Output Voltage Swing vs. Supply
Voltage
0.02
0.018
0.016
DV FROM RAIL (V)
OUTPUT CURRENT (mA)
VCC = 2.7 V
RL = 2.0 W
TA = 25°C
0.014
0.012
VOL
0.01
0.008
VOH
0.006
0.004
0.002
0
1.8
2.2
2.6
3
3.4
3.8
4.2
SUPPLY VOLTAGE (mV)
4.6
Figure 6. Output Voltage vs. Supply Voltage
http://onsemi.com
9
5
5
LMV981, LMV982
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
110
60
90
50
40
70
30
50
Gain
20
10
0
−10
10k
30
PHASE (°)
GAIN (dB)
Phase
10
CL = 200 pF
VS = 1.8 V
RL = 610 W
TA = 25°C
−10
100k
1M
10M
−30
FREQUENCY (Hz)
Figure 7. Gain and Phase vs. Frequency
60
CL = 200 pF
VS = 5 V
RL = 610 W
TA = 25°C
50
Phase
90
45
30
0
20
Gain
−45
10
−90
0
−10
10k
PHASE (°)
GAIN (dB)
40
135
100k
1M
FREQUENCY (Hz)
Figure 8. Gain and Phase vs. Frequency
http://onsemi.com
10
−135
10M
LMV981, LMV982
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
60
110
Phase
90
40
70
30
50
20
10
0
30
Gain
CL = 0 pF
VS = 1.8 V
RL = 100 kW
TA = 25°C
−10
10k
PHASE (°)
GAIN (dB)
50
10
−10
100k
1M
FREQUENCY (Hz)
−30
10M
60
110
50
90
40
70
30
50
20
30
10
0
−10
10k
PHASE (°)
GAIN (dB)
Figure 9. Gain and Phase vs. Frequency
10
CL = 0 pF
VS = 5.0 V
RL = 100 kW
TA = 25°C
−10
100k
1M
FREQUENCY (Hz)
Figure 10. Gain and Phase vs. Frequency
http://onsemi.com
11
−30
10M
LMV981, LMV982
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
80
70
80
VS = 5 V
60
VS = 2.7 V
60
VS = 1.8 V
40
50
PSRR (dB)
CMRR (dB)
100
40
30
20
20
10
0
10
100
1000
0
10
10k
VS = 5 V
100
FREQUENCY (Hz)
Figure 11. CMRR vs. Frequency
10k
Figure 12. PSRR vs. Frequency
10k
10
1k
THD (%)
1
100
VS = 2.7 V
0.1
VS = 1.8 V
10
VS = 5 V
1
10
100
1k
10k
0.01
10
100k
100
FREQUENCY (Hz)
1k
Figure 13. Input Voltage Noise vs. Frequency
Figure 14. THD vs. Frequency
0.6
Falling Edge
0.5
0.4
Rising Edge
0.3
0.2
0.1
0
1.8
10k
FREQUENCY (Hz)
SLEW RATE (V/ms)
INPUT VOLTAGE NOISE (nV/√HZ)
1000
FREQUENCY (Hz)
2.2
2.6
3
3.4
3.8
4.2
4.6
SUPPLY VOLTAGE (V)
Figure 15. Slew Rate vs. Supply Voltage
http://onsemi.com
12
5
100k
LMV981, LMV982
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
VS = 1.8 V
RL = 2 kW
TIME (2ms/div)
Figure 16. Small Signal Noninverting Response
VS = 2.7 V
RL = 2 kW
TIME (2ms/div)
Figure 17. Small Signal Noninverting Response
http://onsemi.com
13
LMV981, LMV982
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
VS = 5.0 V
RL = 2 kW
TIME (2ms/div)
Figure 18. Small Signal Noninverting Response
VS = 1.8 V
RL = 2 kW
TIME (2ms/div)
Figure 19. Large Signal Noninverting Response
http://onsemi.com
14
LMV981, LMV982
TYPICAL CHARACTERISTICS
(TA = 25°C and VS = 5 V unless otherwise specified)
VS = 2.7 V
RL = 2 kW
TIME (2ms/div)
Figure 20. Large Signal Noninverting Response
VS = 5.0 V
RL = 2 kW
TIME (2ms/div)
Figure 21. Large Signal Noninverting Response
http://onsemi.com
15
LMV981, LMV982
TYPICAL CHARACTERISTICS
110
110
100
100
SHORT−CIRCUIT CURRENT (mA)
SHORT−CIRCUIT CURRENT (mA)
(TA = 25°C and VS = 5 V unless otherwise specified)
VCC = 2.7 V
90
VCC = 5 V
80
70
60
VCC = 1.8 V
50
40
30
20
10
0
−40
−20
0
20
40
60
80
100
90
VCC = 5 V
80
70
60
VCC = 2.7 V
50
40
30
20
VCC = 1.8 V
10
0
−40
120
−20
0
20
TEMPERATURE (°C)
80
7
VS = 1.8 V
5
VOS (mV)
25°C
2
−40°C
125°C
1
−40°C
4
85°C
3
120
VS = 2.7 V
125°C
6
5
4
100
Figure 23. Short−Circuit vs. Supply Voltage
(Sourcing)
6
3
2
1
25°C
0
−1
0
85°C
−2
−0.5
0
0.5
1
1.5
2
−3
−0.5
2.5
0
0.5
1
VCM (V)
2
2.5
3
Figure 25. Offset Voltage vs. Common Mode
Range VDD 2.7 V
8
125°C
25°C
6
VS = 5.0 V
4
−40°C
2
85°C
0
−2
−4
−6
1.5
VCM (V)
Figure 24. Offset Voltage vs. Common Mode
Range VDD 1.8 V
VOS (mV)
VOS (mV)
60
TEMPERATURE (°C)
Figure 22. Short−Circuit vs. Supply Voltage
(Sinking)
−1
40
−1
0
1
2
3
4
5
VCM (V)
Figure 26. Offset Voltage vs. Common Mode
Range VDD 5.0 V
http://onsemi.com
16
6
3.5
LMV981, LMV982
APPLICATION INFORMATION
50 k
R1
5.0 k
VCC
VCC
R2
10 k
MC1403
2.5 V
VO
LMV981
VO
LMV981
VCC
−
Vref
−
+
+
1
V ref + V CC
2
R1
V O + 2.5 V(1 )
)
R2
R
R
Figure 27. Voltage Reference
fO +
For: fo = 1.0 kHz
R = 16 kW
C = 0.01 mF
C
C
1
2pRC
Figure 28. Wien Bridge Oscillator
VCC
C
R1
Vin
R2
C
R3
−
Hysteresis
R1
LMV981
Vin
VO
−
VOL
CO = 10 C
Vref
VO
+
VO
+
R2
VOH
Vref
CO
LMV981
VinL
Given: fo = center frequency
A(fo) = gain at center frequency
VinH
Choose value fo, C
Q
Then : R3 +
pf O C
Vref
R1
(V OL * V ref) ) V ref
R1 ) R2
R1
V inH +
(V OH * V ref) ) V ref
R1 ) R2
R1
H+
(V OH * V OL)
R1 ) R2
V inL +
R1 +
R2 +
Figure 29. Comparator with Hysteresis
R3
2 A(f O)
R1 R3
4Q 2 R1 * R3
For less than 10% error from operational amplifier,
((QO fO)/BW) < 0.1 where fo and BW are expressed in Hz.
If source impedance varies, filter may be preceded with
voltage follower buffer to stabilize filter parameters.
Figure 30. Multiple Feedback Bandpass Filter
ORDERING INFORMATION
# of Channels
Specific Device Marking
Package Type
Shipping†
LMV981SQ3T2G*
Single
AAE
SC70−6
(Pb−Free)
3000 / Tape & Reel
LMV981MU3TBG
Single
AE
ULLGA8
(Pb−Free)
3000 / Tape & Reel
LMV982DMR2G*
Dual
V982
Micro10
(Pb−Free)
4000 / Tape & Reel
LMV982MUTAG*
Dual
DE
UQFN10
(Pb−Free)
3000 / Tape & Reel
Order Number
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*Contact factory.
http://onsemi.com
17
LMV981, LMV982
PACKAGE DIMENSIONS
SC−88/SC70−6/SOT−363
CASE 419B−02
ISSUE W
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419B−01 OBSOLETE, NEW STANDARD 419B−02.
D
e
6
5
4
1
2
3
HE
DIM
A
A1
A3
b
C
D
E
e
L
HE
−E−
b 6 PL
0.2 (0.008)
M
E
MILLIMETERS
MIN
NOM MAX
0.80
0.95
1.10
0.00
0.05
0.10
0.20 REF
0.10
0.21
0.30
0.10
0.14
0.25
1.80
2.00
2.20
1.15
1.25
1.35
0.65 BSC
0.10
0.20
0.30
2.00
2.10
2.20
M
A3
C
A
A1
L
SOLDERING FOOTPRINT*
0.50
0.0197
0.65
0.025
0.65
0.025
0.40
0.0157
1.9
0.0748
SCALE 20:1
mm Ǔ
ǒinches
SC−88/SC70−6/SOT−363
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
18
INCHES
NOM MAX
0.037 0.043
0.002 0.004
0.008 REF
0.004 0.008 0.012
0.004 0.005 0.010
0.070 0.078 0.086
0.045 0.049 0.053
0.026 BSC
0.004 0.008 0.012
0.078 0.082 0.086
MIN
0.031
0.000
LMV981, LMV982
PACKAGE DIMENSIONS
ULLGA8, 1.5x1.5, 0.5P
CASE 613AG−01
ISSUE O
A
B
D
PIN ONE
REFERENCE
0.10 C
ÉÉÉ
ÉÉÉ
ÉÉÉ
0.10 C
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.15 AND
0.30 mm FROM THE TERMINAL TIP.
E
DIM
A
A1
b
b1
D
E
e
L
L1
L3
TOP VIEW
0.05 C
A
8X
MOUNTING FOOTPRINT
0.05 C
A1 C
SIDE VIEW
b1
e
8X
3
1
MILLIMETERS
MIN
MAX
−−−
0.40
0.00
0.05
0.20
0.30
0.30
0.40
1.50 BSC
1.50 BSC
0.50 BSC
0.25
0.35
0.05 REF
0.15 REF
SEATING
PLANE
7X
0.32
8X
0.51
PACKAGE
OUTLINE
L
1.65
L3
1
0.42
7
5
L1
DIMENSIONS: MILLIMETERS
8X
b
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
0.10 C A B
BOTTOM VIEW
0.50
PITCH
0.05 C
NOTE 3
http://onsemi.com
19
LMV981, LMV982
PACKAGE DIMENSIONS
Micro10
CASE 846B−03
ISSUE D
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION “A” DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE
BURRS SHALL NOT EXCEED 0.15 (0.006)
PER SIDE.
4. DIMENSION “B” DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION
SHALL NOT EXCEED 0.25 (0.010) PER SIDE.
5. 846B−01 OBSOLETE. NEW STANDARD
846B−02
−A−
−B−
K
D 8 PL
0.08 (0.003)
PIN 1 ID
G
0.038 (0.0015)
−T− SEATING
PLANE
M
T B
S
A
DIM
A
B
C
D
G
H
J
K
L
S
C
H
L
J
10X
MILLIMETERS
MIN
MAX
2.90
3.10
2.90
3.10
0.95
1.10
0.20
0.30
0.50 BSC
0.05
0.15
0.10
0.21
4.75
5.05
0.40
0.70
1.04 SOLDERING FOOTPRINT
0.32 10X
0.041
0.0126
3.20
0.126
8X
4.24
0.167
0.50
0.0196
SCALE 8:1
5.28
0.208
mm Ǔ
ǒinches
Micro10
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
20
INCHES
MIN
MAX
0.114
0.122
0.114
0.122
0.037
0.043
0.008
0.012
0.020 BSC
0.002
0.006
0.004
0.008
0.187
0.199
0.016
0.028
LMV981, LMV982
PACKAGE DIMENSIONS
UQFN10 1.4x1.8, 0.4P
CASE 488AT−01
ISSUE A
EDGE OF PACKAGE
D
ÉÉ
ÉÉ
ÉÉ
PIN 1 REFERENCE
2X
2X
0.10 C
L1
E
0.10 C
EXPOSED Cu
A
0.05 C
A1
0.05 C
A1
C
SIDE VIEW
3
9X
DETAIL A
Bottom View
(Optional)
B
TOP VIEW
10X
5
SEATING
PLANE
ÉÉ
ÉÉ
DIM
A
A1
A3
b
D
E
e
L
L1
L3
MOLD CMPD
A3
DETAIL B
Side View
(Optional)
1.700
0.0669
0.663
0.0261
6
e
1
10 X
L3
b
MILLIMETERS
MIN
MAX
0.45
0.60
0.00
0.05
0.127 REF
0.15
0.25
1.40 BSC
1.80 BSC
0.40 BSC
0.30
0.50
0.00
0.15
0.40
0.60
MOUNTING FOOTPRINT
e/2
L
10
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS
3. DIMENSION b APPLIES TO PLATED TERMINAL
AND IS MEASURED BETWEEN 0.25 AND 0.30 MM
FROM TERMINAL.
4. COPLANARITY APPLIES TO THE EXPOSED PAD
AS WELL AS THE TERMINALS.
A
0.200
0.0079
1
0.10 C A B
0.05 C
9X
0.563
0.0221
2.100
0.0827
NOTE 3
BOTTOM VIEW
0.400
0.0157
PITCH
10 X
0.225
0.0089
SCALE 20:1
mm Ǔ
ǒinches
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
21
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
LMV981/D
Similar pages