Kingbright APT2012ZGC-E 2.0x1.25mm smd chip led lamp Datasheet

2.0x1.25mm SMD CHIP LED LAMP
Part Number: APT2012ZGC/E
Green
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
Features
Descriptions
z 2.0mmx1.25mm SMD LED,0.75mm thickness.
z The Green source color devices are made with InGaN
Light Emitting Diode.
z Low power consumption.
z Electrostatic discharge and power surge could damage
z Wide viewing angle.
the LEDs.
z Ideal for backlight and indicator.
z It is recommended to use a wrist band or anti-
z Package : 2000pcs / reel.
electrostatic glove when handling the LEDs.
z Moisture sensitivity level : level 3.
z All devices, equipments and machineries must be
z RoHS compliant.
electrically grounded.
.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.1(0.004") unless otherwise noted.
3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
4. The device has a single mounting surface. The device must be mounted according to the specifications.
SPEC NO: DSAJ9197
REV NO: V.5B
DATE: NOV/10/2016
PAGE: 1 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.T.Zhang
ERP: 1203009951
Selection Guide
Part No.
Emitting Color (Material)
APT2012ZGC/E
Green (InGaN)
Lens Type
Water Clear
Viewing
Angle [1]
Iv (mcd) [2]
@ 20mA
Min.
Typ.
2θ1/2
500
700
140°
Notes:
1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity / luminous Flux: +/-15%.
3. Luminous intensity value is traceable to CIE127-2007 standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
Parameter
Emitting Color
Typ.
λpeak
Peak Wavelength
Green
λD [1]
Dominant Wavelength
Δλ1/2
Max.
Units
Test Conditions
520
nm
IF=20mA
Green
525
nm
IF=20mA
Spectral Line Half-width
Green
35
nm
IF=20mA
C
Capacitance
Green
100
pF
VF=0V;f=1MHz
VF [2]
Forward Voltage
Green
3.2
4
V
IF=20mA
IR
Reverse Current
Green
50
uA
VR=5V
Notes:
1. Wavelength: +/-1nm.
2. Forward Voltage: +/-0.1V.
3. Wavelength value is traceable to CIE127-2007 standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Values
Units
Power dissipation
120
mW
DC Forward Current
30
mA
Peak Forward Current [1]
100
mA
5
V
450
V
Reverse Voltage
Electrostatic Discharge Threshold (HBM)
Operating Temperature
-40°C To +85°C
Storage Temperature
-40°C To +85°C
Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static
electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.
SPEC NO: DSAJ9197
REV NO: V.5B
DATE: NOV/10/2016
PAGE: 2 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.T.Zhang
ERP: 1203009951
Green
APT2012ZGC/E
SPEC NO: DSAJ9197
REV NO: V.5B
DATE: NOV/10/2016
PAGE: 3 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.T.Zhang
ERP: 1203009951
APT2012ZGC/E
Reflow soldering is recommended and the soldering profile is shown below.
Other soldering methods are not recommended as they might cause damage to the product.
Recommended Soldering Pattern
(Units : mm; Tolerance: ± 0.1)
Reel Dimension
Tape Dimensions
(Units : mm)
SPEC NO: DSAJ9197
REV NO: V.5B
DATE: NOV/10/2016
PAGE: 4 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.T.Zhang
ERP: 1203009951
PACKING & LABEL SPECIFICATIONS
APT2012ZGC/E
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAJ9197
REV NO: V.5B
DATE: NOV/10/2016
PAGE: 5 OF 5
APPROVED: Wynec
CHECKED: Allen Liu
DRAWN: L.T.Zhang
ERP: 1203009951
Similar pages