DATA SHEET GBJ10A~GBJ10K GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes GBJ • Reliable low cost construction utilizing molded plastic technique 0.122(3.1) 0.142(3.6) • Ideal for printed circuit board 0.189(4.8) 0.173(4.4) 0.996(25.3) 0.972(24.7) C 0.118 (3.0) • Plastic material has Underwriters Laboratory Flammability Classification 94V-O Unit: inch ( mm ) 0.146(3.7) 0.129(3.3) • High temperature soldering guaranteed: 0.578(14.7) 0.603(15.3) • Surge overload rating: 200 Amperes peak 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension Case: Reliable low cost construction utilizing 0.669(17.0) 0.709(18.0) MECHANICAL DATA 0.087(2.2) 0.070(1.8) molded plastic technique 0.044(1.1) 0.035(0.9) Terminals: Leads solderable per MIL-STD-202, Method 208 Mounting position: Any 0.304(7.7) 0.288(7.3) Mounting torque: 5 in. lb. Max. Weight: 0.15 ounce, 4.0 grams 0.304(7.7) 0.288(7.3) 0.304(7.7) 0.288(7.3) 0.150(3.8) 0.133(3.4) 0.382(9.7) 0.366(9.3) FEATURES 0.115(2.9) 0.098(2.5) 0.032(0.8) 0.024(0.6) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. GBJ10A Maximum Recurrent Peak Reverse Voltage Maximum RMS Input Voltage Maximum DC Blocking Voltage Maximum Average Forward TC=100°C Rectified Output Current TA= 45°C 50 35 50 GBJ10B GBJ10D 100 70 100 GBJ10G GBJ10J GBJ10K UNIT 400 600 800 V 280 420 560 V 400 600 800 V 200 140 200 10.0 8.0 A I2t Rating for fusing ( t<8.3ms) 166 A2sec Peak Forward Surge Current single sine-wave superimposed on rated load (JEDEC method) 200 Apk Maximum Instantaneous Forward Voltage Drop per element at 5.0A 1.0 Vpk Maximum Reverse Leakage at rated TA=25° 5 CDc Blocking Voltage per element TC=100°C 500 µA µA Typical Thermal Resistance per leg(Note 2) RθJA 18.0 °C / W Typical Thermal Resistance per leg(Note 3) RθJC 3.0 °C / W -55 to +150 °C Operating and Storage Temperature Range, TJ,TSTG NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 3.0 x 3.0" x 0.11" thick ( 7.5 x 7.5 x 0.3cm) AL plate. DATE : AUG.29.2002 PAGE . 1 INSTANTANEOUS FORWARD CURRENT, AMPERES G O CU AMPERES HEAT-SINK MOUNTING, TC (4X4X0.15) INCH COPPER PLATE 60Hz RESISTIVE OR INDUCTIVE LOAD MOUNTED ON 0.5X0.5 INCH COPPER PC BOARD, TA 0.5"(12.7mm) LEAD LENGTH 5.0 TJ = 25 Pulse Width = 30uS 1% Duty Cycle INSTANTANEOUS FORWARD VOLTAGE, VOLT TEMPERATURE Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT INSTANTNEOUS REVERSE CURRENT, MICROAMPERES FORWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) Fig.2 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER ELEMENT 200 160 120 80 40 PERCENT OF PEAK REVERSE VOLTAGE CAPACITANCE, pF Fig.3 - TYPICAL REVERSE CHARACTERISTICS 0 NO. OF CYCLES AT 62Hz Fig.4 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT TJ = 25 f = 1MHz Visg = 50m Vp-p REVERSE VOLTAGE, VOLTS DATE : AUG.29.2002 PAGE . 2