Hittite HMC347LP3 Gaas mmic spdt non-reflective switch, dc - 14 ghz Datasheet

HMC347LP3 / 347LP3E
v06.0805
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 14 GHz
Typical Applications
Features
The HMC347LP3 / HMC347LP3E is ideal for:
High Isolation: >50 dB up to 3 GHz
>45 dB up to 10 GHz
• Basestation Infrastructure
• Fiber Optics & Broadband Telecom
Low Insertion Loss: 1.6 dB @ 10 GHz
• Microwave Radio & VSAT
Non-Reflective Design
• Military Radios, Radar, & ECM
3x3 mm QFN SMT Package
• Test Instrumentation
General Description
Functional Diagram
The HMC347LP3 & HMC347LP3E are broadband
high isolation non-reflective GaAs MESFET SPDT
switches in low cost leadless QFN surface mount
plastic packages. Covering DC to 14 GHz, the switch
offers high isolation and low insertion loss. The switch
features >50 dB isolation up to 3 GHz and >40 dB
isolation up to 13 GHz. The switch operates using
complementary negative control voltage logic lines of
-5/0V and requires no bias supply. This SPDT is an
excellent alternative to the HMC132C8 SPDT.
SWITCHES - SMT
10
Electrical Specifi cations, TA = +25° C, With 0/-5V Control, 50 Ohm System
Parameter
Frequency
Typ.
Max.
Units
1.5
1.6
1.6
1.9
1.9
2.0
2.1
2.4
dB
dB
dB
dB
Insertion Loss
DC - 3.0 GHz
DC - 6.0 GHz
DC - 12.0 GHz
DC - 14.0 GHz
Isolation
DC - 3.0 GHz
DC - 6.0 GHz
DC - 12.0 GHz
DC - 14.0 GHz
49
41
39
33
53
46
44
38
dB
dB
dB
dB
Return Loss
“On State”
DC - 6.0 GHz
DC - 14.0 GHz
10
8
13
13
dB
dB
Return Loss RF1, RF2
“Off State”
DC - 6.0 GHz
DC - 14.0 GHz
7
6
10
9
dB
dB
Input Power for 1 dB Compression
0.5 - 14.0 GHz
19
23
dBm
Input Third Order Intercept
(Two-Tone Input Power= +7 dBm Each Tone)
0.5 - 14.0 GHz
38
43
dBm
3
6
ns
ns
Switching Characteristics
tRISE, tFALL (10/90% RF)
tON, tOFF (50% CTL to 10/90% RF)
10 - 226
Min.
DC - 14 GHz
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC347LP3 / 347LP3E
v06.0805
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 14 GHz
Insertion Loss
Isolation
0
0
ISOLATION (dB)
INSERTION LOSS (dB)
-10
-1
-2
+25 C
+85 C
-40 C
-3
RF1
RF2
-20
-30
-40
-50
-4
-60
-70
0
5
10
15
20
0
5
FREQUENCY (GHz)
Return Loss
15
20
10
0.1 and 1 dB Input Compression Point
30
0
RFC
RF1,RF2 ON
RF1,RF2 OFF
1 dB Compression Point
0.1 dB Compression Point
INPUT P1dB (dBm)
-5
-10
-15
25
20
15
-20
-25
10
0
5
10
15
0
20
2
4
FREQUENCY (GHz)
6
8
10
12
14
16
FREQUENCY (GHz)
Input Third Order Intercept Point
50
45
INPUT IP3 (dBm)
RETURN LOSS (dB)
10
FREQUENCY (GHz)
SWITCHES - SMT
-5
40
+25C
-40C
+85C
35
30
0
2
4
6
8
10
12
14
16
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
10 - 227
HMC347LP3 / 347LP3E
v06.0805
Absolute Maximum Ratings
SWITCHES - SMT
10
10 - 228
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 14 GHz
Control Voltages
RF Input Power (Vctl = -5V)
+27 dBm
State
Bias Condition
Control Voltage Range (A & B)
+0.5V to -7.5 Vdc
Low
0 to -0.5V @ 10 uA Max.
High
-5V @ 10 uA Typ. to -7V @ 40 uA Typ. (± 0.5 Vdc)
Hot Switch Power Level
(Vctl = -5 V)
+23 dBm
Channel Temperature
150 °C
Continuous Pdiss (T=85 °C)
(derate 2mW/ °C above 85 °C)
0.12 W
Thermal Resistance
(Insertion Loss Path)
440 °C/W
Thermal Resistance
(Terminated Path)
540 °C/W
Storage Temperature
-65 to +150 °C
Operating Temperature
-55 to +85 °C
ESD Sensitivity (HBM)
Class 1A
Truth Table
Control Input
A
Signal Path State
B
RFC to RF1
RFC to RF2
High
Low
On
Off
Low
High
Off
On
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC347LP3 / 347LP3E
v06.0805
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 14 GHz
Outline Drawing
SWITCHES - SMT
10
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC347LP3
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC347LP3E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
347
XXXX
[2]
347
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
10 - 229
HMC347LP3 / 347LP3E
v06.0805
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 14 GHz
Suggested Driver Circuit
SWITCHES - SMT
10
10 - 230
Pin Descriptions
Pin Number
Function
Description
1, 5, 9, 12, 16
N/C
This pin should be connected to PCB RF ground to
maximize isolation
2, 4, 6, 8, 13, 15
GND
Package bottom has exposed metal paddle that must also
be connected to PCB RF ground.
3, 7, 14
RFC, RF1, RF2
This pin is DC coupled and matched to 50 Ohm. Blocking
capacitors are required if RF line potential is not equal to 0V.
10
CTLB
See truth table and control voltage table.
11
CTLA
See truth table and control voltage table.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC347LP3 / 347LP3E
v06.0805
GaAs MMIC SPDT NON-REFLECTIVE
SWITCH, DC - 14 GHz
Evaluation PCB
SWITCHES - SMT
10
List of Materials for Evaluation PCB 105711 [1]
Item
Description
J1 - J3
PCB Mount SRI SMA Connector
J4 - J6
DC Pin
R1 - R2
100 Ohm Resistor, 0603 Pkg.
U1
HMC347LP3 / HMC347LP3E
SPDT Switch
PCB [2]
107521 Evaluation PCB
[1] Reference this number when ordering complete evaluation PCB
The circuit board used in the final application
should be generated with proper RF circuit design
techniques. Signal lines at the RF port should have
50 ohm impedance and the package ground leads
and package bottom should be connected directly
to the ground plane similar to that shown above. The
evaluation circuit board shown above is available
from Hittite Microwave Corporation upon request.
[2] Circuit Board Material: Rogers 4350
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
10 - 231
Similar pages