Shoulder HDBF07024A64 Saw filter Datasheet

规格书编号
SPEC NO :
产品规格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
MODEL NO 型 号:
SAW FILTER
HDBF07024A64
PREPARED 编 制:
CHECKED 审 核: Houshihong
APPROVED 批 准: CHARLES
D A T E 日 期: 2007-01-25
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 1 of 7
SAW FILTER
HDBF07024A64
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec No
产品型号
Part No
客户产品型号
Customer No
Tel:0755-82916880
Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 7
SAW FILTER
HDBF07024A64
1.SCOPE
This specification shall cover the characteristics of SAW filter BF07024A64
2. ELECTRICAL SPECIFICATION
DC Voltage VDC
AC Voltage Vpp
Operation temperature
Storage temperature
RF Power Dissipation
10V
10V50Hz/60Hz
-10℃ to +60℃
-40℃ to +85℃
0dBm
Electronic Characteristics
Fo = 70.0 MHz
Terminating source impedance: 50 ohm and matching network
Terminating load impedance: 50 ohm and matching network
Minimu
Maximu
70.0
70.10
31
33
25.6
26.0
26.8
34.8
Center Frequency
MHz
Insertion Loss
dB
1.5dB Bandwidth
20dB Bandwidth
30dB Bandwidth
35dB Bandwidth
45dB Bandwidth
MHz
MHz
MHz
MHz
MHz
24.85
-
24.90
25.54
25.67
25.73
25.83
Passband variation
dB
-
0.8
1.5
Ultimate Rejection
dB
50
55
-
Absolute Delay
usec
-
3.89
-
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
69.90
Typical
-
E-mail:[email protected]
Page 3 of 7
SAW FILTER
HDBF07024A64
3. DIMENSION
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 4 of 7
SAW FILTER
HDBF07024A64
4.TEST CIRCUIT
5. ENVIRONMENTAL CHARACTERISTICS
5-1
High temperature exposure
Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for
24 hours prior to the measurement. It shall fulfill the specifications in table 1.
5-2
Low temperature exposure
Subject the device to -20℃ for 16 hours. Then release the device into the room conditions
for 24 hours prior to the measurement. It shall
5-3
fulfill the specifications in table 1.
Temperature cycling
Subject the device to a low temperature of -40℃for 30 minutes. Following by a high
temperature of +80℃ for 30 Minutes. Then release the device into the room conditions for
24 hours prior to the measurement. It shall meet the specifications in table 1.
5-4
Resistance to solder heat
Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10
±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet
the specifications in table 1.
5-5
Solderability
Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area
of the terminals must be covered with new solder. It shall meet the specifications in table 1.
5-6 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the
specifications in table 1.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 5 of 7
SAW FILTER
HDBF07024A64
5-7 Vibration
Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55
Hz. The device
shall
fulfill the specifications in table 1.
5-8 Lead fatigue
5-8-1 Pulling test
Weight along with the direction of lead without an shock 1kg. The device shall satisfy all the initial
Characteristics.
5-8-2 Bending test
Lead shall be subject to withstand against 90℃ bending with 450g weight in the direction of
thickness. This operation shall be done toward both direction. The device shall show no
evidence of damage and shall satisfy all the initial electrical characteristics.
6.Typical frequency response
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 6 of 7
SAW FILTER
HDBF07024A64
7. REMARK
7.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of the
component. Please avoid static voltage.
7.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid
ultrasonic cleaning
7.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of component.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 7 of 7
Similar pages