Embedded Power for Business-Critical Continuity Rev. 9.10.09_22 DS1200 of 4 DS1200 1200 Watts Distributed Power System Distributed Power Bulk Front-End Total Output Power: 1200 Watts +3.3 Vdc Stand-by Output Wide Range Input Voltage: 90 - 264 Vac Electrical Specifications Special Features • Active power factor correction • EN61000-3-2 harmonic compliance • Active AC inrush control • 1U X 2U form factor • 21.71 W / in3 • +12 Vdc Output • +3.3 Vdc stand-by (5 V standby - consult factory) • No minimum load required • Hot plug operation • N + 1 redundant • Internal OR’ing fets • Active current sharing (10 - 100% load) • Built-in cooling fan (40 mm x 28 mm) • I2C communication interface bus • PMBus compliant • EERPOM for FRU data • Red/green bi-color LED status • Internal fan speed control • Fan Fail Tach Output Signal • INTEL, SSI Std. logic timing • INTEL, SSI Std. FRU data format • Full digital control • One year warranty Safety • UL/cUL 60950 (UL Recognized) • NEMKO+ CB Report EN60950 • EN60950 • CE Mark • China CCC Input Input range: Frequency: 180 - 264 (1200 W) 90 - 264 (1000 W) 47-63 Hz, single phase AC Inrush current: 40 Apk maximum inrush current Efficiency: Conducted EMI: > 91% typical at high line 50% load FCC Subpart J EN55022 Class B Radiated EMI: FCC Subpart J EN55022 Class B Power factor: 0.99 typical Leakage current: 1.40 mA @ 240 VAC Hold up time: 12 ms minimum Output Main DC voltage: Stand-By: +12 V @ 100 A (high line) +12 V @ 81.6 A (low line) +3.3 Vsb @ 6 A (5 V @ 4 A available) Adjustment range: ±5% on +12V only using I2C Regulation: +12 Vdc; +5% / -5% +3.3 Vsb; +5% / -5% +12 Vdc; latches off if overcurrent lasts over 1 second, otherwise it is auto recovery (See Table 1 next page) +3.3 Vsb, 9 A max (hiccup mode) +12 Vdc; 13.2 - 14.4 Vdc +3.3 Vsb; 3.76 - 4.30 Vdc +12 Vdc; 9 - 10.8 V (latch off) 2 second max, 5 - 50 mS, monotonic rise 5 - 50 mS, monotonic rise Over current: Over voltage: Under voltage: Turn-on delay: Main output rise time: Embedded Power for Business-Critical Continuity Logic Control PS_SEATED (A4): TTL logic LOW if power supply is seated into system connector. This is a short pin. A logic HIGH if the PSU is removed Active TTL high when output is within regulation limits. PWR GOOD (C3): AC OK (B1): A low logic level if the input voltage is within allowable limits. A TTL logic HIGH level, and a 5mS early warning signal before 12.0 V DC output loss of regulation. PS_INHIBIT/PS_KILL (B4): This signal is connected to a short pin on the PSU When left open power supply operation will be inhibited. When the power supply is inserted into the system, this pin will be pull low by the system and turn the power supply on only after all other power supply pins have seated. PS ON (A1): The output will be enabled when this signal is pulled low, below 0.8 V outputs disabled when pin is driven high or left open. Rev. 9.10.09_22 DS1200 of 4 Environmental Specifications Operating temperature: Storage temperature: -10° to 50 °C ; 50% power derating at 70 °C -40 °C to +85 °C Altitude, operating: 10,000 ft Electromagnetic susceptibility / Input transients: RoHS & lead-free compliant: -EN61000-3-2, -3-3 -EN61000-4-2, 4.3, 4-4, -4-5, 4-11 Level -EN55024:1998 No tantalum caps. Humidity: Shock and vibration specificatons: 20 to 90% RH, non-condensing Complies with Astec Std. Specifications, Q3205 MTBF (Demonstrated): 500K Hrs at full load, 40 °C Ordering Information Model Number DS1200-3 DS1200-3-002 DS1200-3-003 DS1200-3-004 Nominal Output Set Point Voltage Set Point Tolerance 12.0 Vdc ±0.2% 12.0 Vdc ±0.2% 12.0 Vdc ±0.2% 12.0 Vdc ±0.2% Total Regulation ±5% ±5% ±5% ±5% Minimum Maximum Output Ripple Over Current Current Current P/P 0A 100 A 120 mV 118 A - 147.6 A* 0A 100 A 120 mV 118 A - 147.6 A* 0A 85 A 120 mV 118 A - 147.6 A* 0A 85 A 120 mV 118 A - 147.6 A* Stand-by Air Flow 3.3 V @ 6 A 5.0 V @ 4 A 3.3 V @ 6 A STD STD REV 5.0 V @ 4 A REV *Over current latches off if overcurrent lasts over 1 seconds, otherwise it is auto recovery. Reverse Air Derating Output Power (W) 1400 1140W @ 25 °C 1200 1025W @ 50 °C 1000 800 760W @ 70 °C 600 400 200 0 0 20 25 Ambient Temperature (°C) 50 70 Output Power Embedded Power for Business-Critical Continuity Rev. 9.10.09_22 DS1200 of 4 Mechanical Drawing Condition LED Status Stand-by - ON; Main output - OFF; AC PRESENT Blinking green Stand-by - ON; Main output - ON; Solid green Main output OCP, UVP, OVP Blinking Amber FAN_FAULT; OTP; Stand-by OCP/UVP Amber AIRFLOW DIRECTION 279.4 ± 1.0 200.9 7.02 ± 0.80 EMI GASKET - LEIRD 77-018 (3X) (200.9) (3X) EMI GASKET - LEIRD 77-018 LABEL MODEL 30.0 HANDLE LATCH 8.0 3.2 PROGRAMMING WINDOW 275.5 ± 0.7 81.3 ± 0.8 FAN 36 X 36 X 28MM C19 AC-INLET 200.9 5.7 ± 0.5 EMI GASKET - LEIRD 77-018 7.6 39.9 ± 0.5 18.4 ± 0.5 16.1 PURE ORANGE WAVE LENGTH: 607 GREEN WAVE LENGTH: 565 1.9 7.2 ± 0.5 15.3 ± 0.5 68.8 6.0 (2X) 1.5 X 45° CHAMPER RECOMMENDED KEY HEIGHT IS 2.5MM MAX. 9.0 Embedded Power for Business-Critical Continuity Americas DC Output Connector Pinout Assignment 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Male connector as viewed from the rear of the supply: D1 D2 D3 D4 D5 D6 C1 C2 C3 C4 C5 C6 B1 B2 B3 B4 B5 B6 A1 A2 A3 A4 A5 A6 PB1 PB2 PB3 PB4 PB5 PB6 P1 - Power Supply Side 1. 2. FCI Power Blade 51721 series 51721-10002406AA Molex Power Connector SD-87667 series 87667-7002 Mating Connector (System Side) 1. 2. FCI Power Blade 51741-10002406CC Straight Pins FCI Power Blade 51761-10002406AALF Right Angle Rev. 9.10.09_22 DS1200 of 4 Europe (UK) Pin Assignments Pin PB 1 PB 2 PB 3 PB 4 PB 5 PB 6 A1 A2 A3 A4 A5 A6 B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 D1 D2 D3 D4 D5 D6 Signal Name Main output return Main output return Main output return + Main output + Main output + Main output PS_ON Main output remote sense return Spare PS_SEATED (Power Supply Seated) STAND-BY STAND-BY RETURN AC_OK (AC Input Present) Main output remote sense Main output current share PS_INHIBIT / PS_Kill STAND-BY STAND-BY RETURN SDA (I2C Data Signal) SCL (I2C Clock Signal) POWER GOOD Spare STAND-BY STAND-BY RETURN A0 (I2C Address BIT 0 Signal) A1 (I2C Address BIT 1 Signal) S_INT (Alarm) STAND-BY RMT SENSE STAND-BY STAND-BY RETURN Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.PowerConversion.com techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2009 Emerson Electric Co.