Advanced Monolithic Systems AMS78LXX 100mA VOLTAGE REGULATOR FEATURES APPLICATIONS • 5.0V, 6.2V and 8.0V Output Voltage Available* • Output Voltage Tolerance of ± 5% Over Temperature • Output Current in excess of 100mA • Internal Thermal Overload Protection • Overvoltage Protection • Short Circuit protection • TO-92, SO-8 and SOT-89 Packages Available • Battery Powered Systems • Portable Consumer Equipment • Cordless Telephones • Portable (Notebook) Computers • Portable Instrumentation • Radio Control Systems • Logic Systems GENERAL DESCRIPTION The AMS78LXX series consists of positive fixed voltage regulators ideally suited for use in battery-powered systems. These devices feature very low quiescent current of 1mA or less when supplying 10mA loads. This unique characteristic and the low input -output differential of less than 1V required for proper regulation, make the AMS78LXX ideal to use for standby power systems and portable equipment. The AMS78LXX series also includes internal current limiting, over voltage protection, thermal shutdown, and is able to withstand temporary power-up with mirror-image insertion. The AMS78LXX series is offered in the 3-pin TO-92 package, 8-pin plastic SOIC and SOT-89 packages. ORDERING INFORMATION OUTPUT PACKAGE TYPE TO-92 8 LEAD SOIC VOLTAGE* 5.0V AMS78L05N AMS78L05S 6.2V AMS78L62N AMS78L62S 8.0V AMS78L08N AMS78L08S * For other fixed voltages consult factory. OPER. TEMP SOT-89 AMS78L05L AMS78L62L AMS78L08L RANGE IND IND IND PIN CONNECTION TO-92 Plastic Package (N) OUTPUT 8L SOIC SO-Package (S) INPUT OUTPUT 1 SOT-89 Package (L) 8 INPUT GROUND 2 7 GROUND GROUND 3 6 GROUND 1 GND N/C 4 INPUT Bottom View Advanced Monolithic Systems, Inc. 2 3 5 N/C Top View GND OUTPUT Front View 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS78LXX ABSOLUTE MAXIMUM RATINGS (Note 1) Input Voltage Power Dissipation (Note 4) Operating Junction Temperature 24V Internally Limited 0°C to +125°C Storage Temperature -65°C to +150°C Lead Temperature (Soldering 10 sec) 230°C ESD 1000V ELECTRICAL CHARACTERISTICS AMS78L05 Electrical Characteristics at VIN =10V, IO =10mA, TJ=25°C, C1=0.33µF, CO = 10µF unless otherwise specified. PARAMETER CONDITIONS Min. Typ. Max. Units 4.80 5.0 5.2 V 5.25 V (Note 2) Output Voltage 7V ≤V ≤20V, IO=100 mA IN -40°C ≤T ≤125°C 4.75 J Line Regulation 7V ≤V ≤ 20V 18 75 8V ≤V ≤ 20V 10 54 1mA ≤I ≤ 100 mA 20 60 1mA ≤I ≤ 40 mA 5 30 0.6 1.0 IN IN Load Regulation O O Quiescent Current Output Noise Voltage 10Hz-100kHz Peak Output Current Average Output Voltage Tempco I = 5 mA Ripple Rejection fO = 120Hz O 8V ≤V ≤ 16V 47 mV mV mA 40 µV 200 mA -0.65 mV/°C 62 dB IN Minimum Value of Input Voltage Required to Maintain Line Regulation 5.6 6.0 V AMS78L62 Electrical Characteristics at VIN =12V, IO =10mA, TJ=25°C, C1=0.33µF, CO = 10µF unless otherwise specified. PARAMETER CONDITIONS Min. Typ. Max. Units 5.95 6.2 6.45 V 6.5 V mV (Note 2) Output Voltage 8.5V ≤V ≤20V, IO=100 mA IN -40°C ≤T ≤125°C 5.9 J Line Regulation 8.5V ≤V ≤ 20V 65 175 9V ≤V ≤ 20V 55 125 1mA ≤I ≤ 100 mA 13 80 1mA ≤I ≤ 40 mA 6 40 0.6 1.0 IN IN Load Regulation O O Quiescent Current Output Noise Voltage 10Hz-100kHz Peak Output Current Average Output Voltage Tempco I = 5 mA O Advanced Monolithic Systems, Inc. mV mA 50 µV 200 mA -0.75 mV/°C 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS78LXX ELECTRICAL CHARACTERISTICS (Continued) AMS78L62 Electrical Characteristics at VIN =12V, IO =10mA, TJ=25°C, C1=0.33µF, CO = 10µF unless otherwise specified. PARAMETER CONDITIONS Min. Typ. 40 46 Max. Units (Note 2) Ripple Rejection fO = 120Hz 10V ≤V ≤ 20V dB IN Minimum Value of Input Voltage Required to Maintain Line Regulation 6.8 7.0 V AMS78L08 Electrical Characteristics at VIN =14V, IO =10mA, TJ=25°C, C1=0.33µF, CO = 10µF unless otherwise specified. PARAMETER CONDITIONS Min. Typ. Max. Units 7.60 8.0 8.40 V 8.40 V mV (Note 2) Output Voltage 11V ≤V ≤23V, IO=100 mA IN -40°C ≤T ≤125°C 7.60 J Line Regulation 11V ≤V ≤ 23V 80 175 12V ≤V ≤ 23V 70 125 1mA ≤I ≤ 100 mA 15 80 1mA ≤I ≤ 40 mA 8 40 0.6 1.0 IN IN Load Regulation O O Quiescent Current Output Noise Voltage 10Hz-100kHz Peak Output Current Average Output Voltage Tempco I = 5 mA Ripple Rejection fO = 120Hz O 12V ≤V ≤ 22V 39 mV mA 60 µV 200 mA -0.78 mV/°C 45 dB IN Minimum Value of Input Voltage Required to Maintain Line Regulation 9.0 9.5 V Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: See Circuit in Typical Applications. To ensure constant junction temperature, low duty cycle pulse testing is used. Note 3: Limits appearing in boldface type apply over the entire junction temperature range for operation. Limits appearing in normal type apply for TA = TJ = 25°C. Note 4: The junction-to-ambient thermal resistance are as follows: 195°C/W for the TO-92 (N) package, 160°C/W for the molded plastic SO-8 (S), 150°C/W for the SOT-89 package. Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS78LXX TYPICAL PERFORMANCE CHARACTERISTICS Peak Output Current 0.5 500 5.0 IO = 100mA 0.4 0.3 0.2 0.1 TJ= 25°C 400 TJ = 85°C 300 TJ = -40°C 200 100 4 2 0 0 10 20 30 40 50 60 INPUT VOLTAGE (V) OUTPUT VOLTAGE DEVIATION (mV) 6 3 2 1 0 -1 -2 ~ -3 ~ VIN = V OUT = 9V C2= 100 µF ~ ~ 3 0 15 30 TIME (µs) 0 Quiescent Current 2.0 45 LOAD CURRENT(mA) 8 3.0 4.0 5.0 6.0 INPUT VOLTAGE (V) Load Transient Response 40 C2= 100µF 0 -40 ~ ~ ~ ~ 150 0 0 Quiescent Current 35 15 30 TIME (µs) 45 Quiescent Current 30 25 QUIESCENT CURRENT (mA) 5V OUTPUT 25 20 15 10 2.0 30 IO= 100mA 5 IO= 50mA 0 -5 -20 -10 VIN = 14V 25 20 15 10 5 0 0 10 20 30 40 50 60 INPUT VOLTAGE (V) Advanced Monolithic Systems, Inc. 0 60 30 90 OUTPUT CURRENT (mA) QUIESCENT CURRENT (mA) OUTPUT VOLTAGE (V) AMS78L05 RL=500Ω -2 -20 -10 10 20 INPUT VOLTAGE (V) Line Transient Response INPUT VOLTAGE OUTPUT VOLTAGE CHANGE (V) DEVIATION (mV) Output at Voltage Extremes 12 30 3.0 0 0 80 120 40 JUNCTION TEMPERATURE (° C) AMS78L05 IO = 100mA 4.0 0 0 10 OUTPUT VOLTAGE (V) 6.0 0 QUIESCENT CURRENT (mA) Low Voltage Behavior 600 OUTPUT CURRENT (mA) INPUT OUTPUT DIFFERENTIAL (V) Dropout Voltage 0.6 20 15 10 ~ ~ 3 ~ ~ IO = 50mA 2 1 0 -40 IO = 0mA 0 40 80 120 TEMPERATURE (° C) 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS78LXX TYPICAL PERFORMANCE CHARACTERISTICS (Continued) Maximum Power Dissipation (SO-8) Maximum Power Dissipation (SOT-89) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 1.0 0.9 0.2 0 0 10 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE (° C) Maximum Power Dissipation (TO-92) POWER DISSIPATION (W) POWER DISSIPATION (W) POWER DISSIPATION (W) 1.0 0.9 2.2 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.8 0.7 0.125" Lead Lenght from PC Board 0.6 0.5 0.4 0.4" Lead Lenght from PC Board 0.3 0.2 0.1 0 0 10 20 30 40 50 60 70 80 90 100 AMBIENT TEMPERATURE (° C) 0 10 20 30 40 50 60 70 80 AMBIENT TEMPERATURE (° C) TYPICAL APPLICATIONS Fixed Output Regulator VIN UNREGULATED INPUT VOUT REGULATED OUTPUT AMS78LXX C1* 0.33µF GND C2** 10µF IQ *Required if regulator is located far from power supply filter. **C2 must be at least 10µF to maintain stability; it can be increased without bound to maintain regulation during transients and it should be located as close as possible to the regulator. This capacitor must be rated over the same operating temperature range like the regulator. Current Regulator INPUT AMS78LXX C1 0.33µF R1 OUTPUT IOUT IOUT = (VOUT/R1)+IQ >IQ = 1.5mA over line and load changes Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS78LXX PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted. 3 LEAD TO-92 PLASTIC PACKAGE (N) 0.180±0.005 (4.572±0.127) 0.060±0.005 (1.524±0.127) DIA 0.060±0.010 (1.524±0.254) 0.90 (2.286) NOM 0.180±0.005 (4.572±0.127) 0.140±0.010 (3.556±0.127) 5° NOM 0.500 (12.70) MIN 0.050 (1.270) MAX UNCONTROLLED LEAD DIMENSIONS 0.015±0.002 (0.381±0.051) 0.016±0.003 (0.406±0.076) 0.050±0.005 (1.270±0.127) 10° NOM N (TO-92 ) AMS DRW# 042391 8 LEAD SOIC PLASTIC PACKAGE (S) 0.189-0.197* (4.801-5.004) 8 7 6 5 0.228-0.244 (5.791-6.197) 0.150-0.157** (3.810-3.988) 1 2 3 4 0.010-0.020 x 45° (0.254-0.508) 0.053-0.069 (1.346-1.752) 0.004-0.010 (0.101-0.254) 0.014-0.019 (0.355-0.483) 0.008-0.010 (0.203-0.254) 0.050 (1.270) TYP 0°-8° TYP 0.016-0.050 (0.406-1.270) S (SO-8 ) AMS DRW# 042293 *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140 AMS78LXX PACKAGE DIMENSIONS inches (millimeters) unless otherwise noted (Continued). SOT-89 PLASTIC PACKAGE (L) 0.173-0.181 (4.40-4.60) 0.055-0.063 (1.40-1.60) 0.014-0.017 (0.35-0.44) 0.064-0.072 (1.62-1.83) 0.155-0.167 (3.94-4.25) 0.084-0.090 (2.13-2.29) 0.090-0.102 (2.29-2.60) 0.035-0.047 (0.89-1.20) 0.059 (1.50) BSC 0.014-0.019 (0.36-0.48) 0.017-0.022 (0.44-0.56) L (SOT-89 ) AMS DRW# 042392 0.118 (3.00) BSC Advanced Monolithic Systems, Inc. 6680B Sierra Lane, Dublin, CA 94568 Phone (925) 556-9090 Fax (925) 556-9140